Intellinet 503495 User manual

GIGABIT
INDUSTRIAL
ETHERNET
SWITCH
USER
MANUAL
MODELS
503495,
503532,
503570
INT-503495/503532/503570-UM-0308-01
Model shown: 503495

INTRODUCTION
Thank you for purchasing this INTELLINET NETWORK SOLUTIONS™
Industrial Gigabit Ethernet Switch:
• Model 503495 (6-port 10/100Base-TX + 2-port 1000Base-SX [SC]
Multi-Mode);
• Model 503532 (6-port 10/100Base-TX + 2-port 1000Base-LX [SC]
Single-Mode); or
• Model 503570 (6-port 10/100Base-TX + 2-port 10/100/1000Base-TX).
Specically designed for industrial Ethernet applications, this switch has
all the functions of an unmanaged switch in a robust, aluminum case
that offers IP30-standard protection.
To meet industrial device-redundancy requirements, the Industrial Gigabit
Ethernet Switch is equipped with a terminal block to provide dual power
inputs with reverse polarity protection. Plus, store and forward switching
architecture greatly increases the network efciency: It delivers true non-
blocking switching performance to all ports running at full wire speed
without any loss of packets.
Easy-to-follow instructions in this user manual help make installation of
the switch quick and simple, so you’ll also soon be enjoying the benets
of these additional features:
• Auto-sensing RJ-45 ports automatically detect optimal network speeds
• All RJ-45 ports with Auto MDI-X and NWay auto-negotiation support
• Alarm relay output to alert of power failure
• Full/half duplex operation
• Supports IEEE 802.3x ow control on full duplex and back pressure
on half duplex
• Supports 2048 MAC address entries
• 128 kBytes buffer memory
• LEDs for link/activity and full/half duplex
• DIN rail kit, or wall-mounting ears for 3-way installation
• Terminal block to provide dual power inputs with reverse polarity
protection
• Lifetime Warranty
3

HARDWARE
DIN-Rail Installation
1. Angle the switch’s mounting clamp relative to the DIN rail (above left)
so that the rail is positioned under the upper lip of the clamp and behind
the metal springs.
2. Push the switch toward the DIN rail until the spring on the mounting
clamp clicks in place on the rail (above right).
Wall-Mount Installation
1. Remove the DIN rail
mounting clamp from the
back of the switch.
2. Attach the wall-mount panel
to the back panel of the
switch using the six included
screws.
3. With the wall-mount panel
securely connected, attach
the switch to a wall or other
suitably sturdy vertical
surface.
4
DIN rail
Mounting
clamp
Switch
Spring
Wall-mount panel
Switch

Front-Panel Ports & Indicators
1 Gigabit ports
2 LEDs
3 Fast Ethernet ports
Bottom-Panel Connectors
The terminal block connections (L-R):
GND, V1+ and V1– (PWR 1), Relay
Output (1 A / 24 V DC), V2+ and V2–
(PWR 2).
To the right of the terminal block is
the PWR 3 jack (12–45 V DC).
5
Model 503495 Model 503570
Model 503532
1 1
22
3 3
GND V1+ V1– Relay V2+ V2–
12–48 V DC
power jack

SPECIFICATIONS
6
Standards(Models503495/503532)
• IEEE 802.3 (10Base-T Ethernet)
• IEEE 802.3u (100Base-TX Fast
Ethernet)
• IEEE 802.3x (ow control, for full
duplex mode)
• IEEE 802.3z (Fiber Optic Gigabit
Ethernet)
Standards(Model 503570)
• IEEE 802.3 (10Base-T Ethernet)
• IEEE 802.3ab (Gigabit Ethernet)
• IEEE 802.3u (100Base-TX Fast
Ethernet)
• IEEE 802.3x (ow control, for full
duplex mode)
General
• Media support:
- Model 503495:
• 10Base-T Cat3, 4, 5 UTP/
STP RJ-45
• 100Base-TX Cat5 UTP/STP
RJ-45
• 1000Base-SX multi-mode
50/125 µm & 62.5/125 µm
ber
- Model 503532:
• 10Base-T Cat3, 4, 5 UTP/
STP RJ-45
• 100Base-TX Cat5 UTP/STP
RJ-45
• 1000Base-LX single-mode
9/125 µm ber
- Model 503570:
• 10Base-T Cat3, 4, 5 UTP/
STP RJ-45
• 100Base-TX Cat5 UTP/STP
RJ-45
• 1000Base-T Cat5 UTP/STP
RJ-45
• Packet lter/forwarding rate:
- 1,488,000 pps (1000 Mbps)
- 148,800 pps (100 Mbps)
- 14,880 pps (10 Mbps)
• Buffer memory: 128 kBytes
• MAC address table: 2048 entries
• Backplane speed: 3.2 Gbps
• Switch architecture: store and
forward
• Certications: FCC Class A,
EN55022 Class A, CE Mark
LEDs
• LINK/ACT
• Full/half duplex
Power
• Power supply:
- Input voltage: 24 V DC (12 –
48 V DC), dual inputs
- Reverse polarity protection:
present
• Power consumption:
- Model 503495: 5.5 Watts
(maximum) at 24 V
- Model 503532: 5.7 Watts
(maximum) at 24 V
- Model 503532: 5.1 Watts
(maximum) at 24 V
Environmental
• Aluminum housing, IP30 protection
• Dimensions: 53 x 135 x 105 mm
W x H x L (2.1 x 5.3 x 4.1 in.)
• Weight:
- Models 503495/503532:
750 g (1.7 lbs.)
- Model 503570:
700 g (1.5 lbs.)
• Operating temperature: -10 –
70°C (14 – 158°F)
• Operating humidity: 5 – 95% RH,
non-condensing
• Storage temperature: -40 –
85°C (-40 – 185°F)
Regulatory Approvals
• EMI:
- FCC Class A
- EN55022 Class A
• EMC:
- EN61000-4-2
- EN61000-4-3
- EN61000-4-4
- EN6100-4-5
- EN6100-4-6
• Safety:
- UL
- cUL
- CE/EN60950
• Shock: IEC 60068-2-27
• Freefall: IEC 60068-2-32
• Vibration: IEC 60068-2-6
• MTBF:
- Model 503495:
283,492 hours
- Model 503532:
280,653 hours
- Model 503570:
287,250 hours
Calculated MTBF is based on
MIL-HDBK-217F (Military
Handbook) standard
Package Contents
• Industrial Gigabit Ethernet
Switch
• User manual

INTELLINET NETWORK SOLUTIONS™offers a complete line
of active and passive networking products.
Ask your local computer dealer for more information or visit
www.intellinet-network.com.
Copyright © INTELLINET NETWORK SOLUTIONS
All products mentioned are trademarks or registered trademarks of their respective owners.