Intellinet 509961 User manual

10/100Mbps PCI Ethernet Hub Card
With switch Feature
User's Manual
Switch.HC v2.1 May 00’
Item Number: 509961

2
Introduction
Thank you for purchasing our high performance
Ethernet 10/100M switch Hub card. This guide is to
provide the installation and usage of the product
for network installers or users.
The product combines with one PCI 10/100Mbps
Ethernet and 5 port 10/100Base switch hub function
for the SOHO application Extensive driver support for
commonly used network operating systems is
available.
Hardware Overview
The PCI switch hub card has two models. One is
status display on the bracket and another is on the
3.5” diskette’s panel. The PCI is a 32-bit Ethernet card
which offers users the highest performance in the
architecture.
It is a PCI bus Ethernet card and a 5 port hub, you can
use the enhance drivers provided for the LAN cards. It
allows users to configure the hardware by using
software, or Plug & Play mode and the auto-setup
feature makes the card to be truly " Plug & Play ".

3
Features & Benefits :
32-bit high performance Ethernet card.
Support Plug & Play function.
Using turbo drivers to enhance transfer rate.
Support multi-card drivers in Plug & Play mode.
Configuration by software or mainboard‘s BIOS.
Plug and play, auto-setup IRQ and I/O address.
Support one PCI 10/100Mbps LAN card, and 4 TP
ports .
Compliance with IEEE 802.3 CSMA/CD, 100Base
TX and 10Base-T standard, Full-duplex data
transfer rate.
Supports Netware ODI & IPX, NDIS Driver for LAN
Manager, Microsoft Windows for Workgroups,
Microsoft NT, WIN 95/98/2000, SCO UNIX driver
and Packet Driver for TCP/IP.
Provides diagnostic software and LEDs for any port
to indicate network activity.
Supports smart remote boot ROM.
Hardware Installation
To insert a card into your computer, do the following:
1.Turn off the computer and remove its cover.
2.Insert the Hub card into a PCI slot which is assigned
slave
or auto mode by the BIOS. If needed, refer to your
PCI

4
computer‘s setup and installation guide.
3.Secure the card to the rear of the computer chassis
and
put back the computer cover.
4.Connect the product to other 10Mbps or 100Mbps
network card using twisted-pair cables.
5.The hub provides a switch for port 4 optional normal
or
uplink function. The uplink is making it easy to link
two
hubs together.
LED Indicators
The Hub card is equipped with LED indicators to
provide for display of the card status and enable
diagnosis of system problems.
Link/Activity status LED : Green .
When a link window is detected, this LED will light up,
showing that the link is good. If this indicator is OFF,
check RJ-45 twisted pair cabling connections. This
LED will blink whenever a packet is transmitted or
received.
PWR/Power/Activity : Green.
Upon power on, this LED is ON. It is flashing at certain
time intervals, to show network activity.
Software Configuration & Driver Installation
Please refer to the readme.txt or driver.txt provided in
the diskette for detail description in running the

5
software.
Appendix A : Technical Specification
Topology : Star/Bus.
Protocol : CSMA/CD
(Carrier Sense Multiple Access with Collision
Detection).
Connector : RJ45 .
Standard : IEEE 802.3 10Base/100Base
Trans Rate :10Mbps or 100Mbps (STP only ).
Hardware : PCI Bus compliant PCs.
Cable : AWG 22-26 STP or UTP cable.
Distance : UTP or STP cable 100 meters for
link segments.
600 meters for multiple hubs.
IRQ Line : INTA on PCI slot ,
(which is mapped to the BIOS‘s IRQ setup)
I/O Address : Automatically decided by
configuration space.
Boot ROM Address : Automatically decided by
configuration space.
Software : Refer the disk
Temperature : 0 to 55 ( Operating ).
Humidity : 10% to 90% (Non-
condensing ).
Power : 3.5 Watts (Max).
Certification : FCC Part 15 Class A.
CE approved.

6
Copyright
Copyright2000 by the manufacture of the prduct.
ALL rights reserved. No part of this manual may be
reproduced, transcribed, stored in a retrieval system,
translated into any language or computer language, or
transmitted in any form whatsoever without the prior
written consent of the manufacturer.
All brand names and models mentioned in this manual
are for reference only and are considered to be
trademarks or registered trademarks of their
respective owners.
No statutory claims or warranties are expressed or
implied herein as to the fitness or merchant ability of
this product for any particular purpose. The
manufacturer reserves the right to change or modify
the specifications of any one or all of these products
as deemed necessary at any time without prior
notification. The manufacturer further
reserves the right to delete, change, modify, or append
any detail or section of this manual at any time without
prior notification.