Intellisystem ThermalTronix TT-1040S-UTCM User manual

ThermalTronix
TT-1040S-UTCM
TT-1075S-UTCM
Thermal Imaging Camera
User Manual

1
Warnings
Please avoid aiming the lens at extreme high temperature radiation source, such as the sun,
molten steel or laser in any situation; otherwise the detector may be damaged.
Please do not touch the lens to avoid contaminating and damaging. Please pay attention to
protect the lens to avoid causing abrasion, scratches even breaches, otherwise, it will affect
the device performance badly, even damage the device.
This device is a precise optoelectronic product. Please protect it properly during usage,
storage and transportation, where improper use (such as drop and collision) will cause
damage to the device. If the internal connection is broken during the assembly process or the
apparatus is damped (rain wet), the performance will be reduced and even the device will be
damaged.
Make sure that the power control connection is reliable. If the power control wire is in bad
connection, it will damage the device.
Ensure the proper connection of power control cable and data cable. Wrong connection may
cause damage to the device.
Do not swag fiercely or collide the device during transportation, otherwise, it will cause
performance-reduction and even damage to it.
Please use the specified power supply; otherwise, it will cause improper working, even
damaging the apparatus.
If the product works abnormally, please contact the dealer or the nearest after-sale service center.
Please do not dismantle or replace it in any manners.

2
Table of Contents
1. Overview......................................................................................3
2. Getting started.............................................................................4
2.1. How to assembly..................................................................................................4
2.2. Control panel.......................................................................................................4
2.3. Interfaces & connectors.......................................................................................6
2.3.1. Video output interface................................................................................6
2.3.2. Multiple interface ......................................................................................6
3. Operation guide...........................................................................7
3.1. Menu description.................................................................................................7
3.1.1. Main menu................................................................................................7
3.1.2. System menu.............................................................................................9
3.1.3. Communication menu................................................................................9
3.1.4. Mode menu.............................................................................................10
3.2. Main operation description ...............................................................................10
3.2.1. Focusing.................................................................................................10
3.2.2. Single pixel correction setup ....................................................................10
3.2.3. Auto imaging mode setup ........................................................................11
3.2.4. Imaging mode selection ...........................................................................11
3.2.5. Gain setup...............................................................................................12
3.2.6. Brightness setup ......................................................................................12
3.2.7. Polarity setup ..........................................................................................12
3.2.8. Image enhancement setup ........................................................................13
3.2.9. Crosshair setup........................................................................................13
3.2.10. Dead pixel correction setup......................................................................13
4. Troubleshooting.........................................................................14
5. Technical specifications.............................................................15

3
1. Overview
The Figure.1.1 shows the overall dimension of the camera.
Figure.1.1 Overview of the camera
Figure.1.2 Back of the camera

4
2. Getting started
2.1. How to assembly
1．Check all units are in accordance with the packing list.
2．Make sure all parts are well-protected in the carry case.
3．Carefully take out the camera and other accessories.
4．Connect the video connector to the monitor.
5．Connect the power adapter and power cable
6．Connect the power cable to the power supply to power on the camera.
2.2. Control panel
The camera provides a control panel with five shortcut keys with various functions. The below is
the figure of the control panel:
Figure.2.2.1 Control panel

5
The five keys have the below functions respectively:
+ UP key. When the menu is activated, press UP to adjust the selected parameters.
The parameter value will be increased after pressing. When the menu is not
activated, press UP to focus forwards.
- DOWN key. When the menu is activated, press DOWN to adjust the selected
parameters. The parameter value will be decreased after pressing. When the menu
is not activated, press DOWN to focus backwards.
M MEMU key. Press to activate or hide the menu. Press MENU to select the
parameter, and modify the parameter value via UP or DOWN keys. Continuing
pressing MENU key, the function option will be selected circularly. After one cycle,
the menu will disappear and the change will be saved. The parameter setting will
be the last-time setting after restarting next time.
C Calibration key. Long press (≥3s) to do calibration manually.
F Setting key. Press to activate the setting menu. (Do not suggest the end-user to
change the settings)

6
2.3. Interfaces & connectors
2.3.1. Video output interface
Figure.2.3.1.1 Video output interface
The above figure is a BNC video output interface.
2.3.2. Multiple interface
Figure.2.3.2.1 Multiple interface
The definition of each pin is as below:
No.
Pin name
Description
1
+12V
Positive power input
2
GND
Power ground
3
RS485A
RS485+
4
RS485B
RS485-
5
I/O1
User port
6
I/O2
User port
7
I/O3
User port
8
I/O4
User port
9
I/O5
User port
10
COM

7
.
3. Operation guide
3.1. Menu description
3.1.1. Main menu
Press MENU button to activate main control menu. Press UP or DOWN button to change the
Option value. Press MENU button until Exit: option is selected and press UPbutton or DOWN
button to exit.
Figure.3.1.1.1 Main menu interface
Auto: XXX Display the current image auto mode. Three options:
0: manual gain, manual brightness;
1: manual gain, auto brightness;
2: auto gain, auto brightness;
Mode: XXX Display the current image mode. There are 10 options, where 0 and 1 are
fixed factory default settings and 2-9 are user-defined settings.

8
0: Suitable for observation of big-object under good weather condition
1: Suitable for observation of target within sky-line under good weather
condition
2～9: User-defined based on different practical occasions.
Note: when Auto 0 and 1, Mode X cannot be adjusted; when Auto 2, Mode X can be
adjusted.
G: XXX Gain value, range: 0-255
B: XXX Brightness value, range: -2048-+2048
P: XXX White/black hot display mode
0: black hot 1: white hot
Z: XXX Zoom status
1: No zoom 2: 2X
E: XXX Image enhancement status
Y: on N: off
C: XXX Display the crosshair or not.
Exit: Exit crosshair menu. Press MENU button to select the Exit option and press UP
button to exit the menu.
Note: When exiting the main menu, any change will be saved automatically and will also be used
when restarting next time.
Mode: XXXcan only choose the existed mode, but can not adjust it.

9
3.1.2. System menu
Press F button and enter the password: MC+—MC, will pop up the below interface:
Figure.3.1.2.1 System menu
AF: XXXautomatic focusing;
RS: XXX Set the zeroing parameter
Video: XXX Set the image quality
Protect: XXX Set the switch status to protect the detector from being burned
Y: on N: off
Alarm: XXX Reserved for alarm;
Recover: XXX Recover all menus setting for factory default
Exit: Exit setting menu. Press MENU button to select the Exit option and press
UP button to exit the menu.
3.1.3. Communication menu
In System menu, press M button to select Com: XXX, and press + or –button to enter the
password: +-MC+-, will pop up the below interface:
Figure.3.1.3.1 Communication menu
ID: XXXID number, range: 0~+255.
BaudRate: XXX Set Baud rage value;
Protocol: XXX Select the communication protocol. Three options: INTELLISYSTEM,
PELCO-D and PELCO-P;
Com: Mode: AF: RS: Video: Protect: Alarm: Recover Exit:
ID: BaudRate: Protocol: Exit:

10
Exit: Exit configuration setup. Press MENU button to select the Exit option and
press UP button to exit the menu.
3.1.4. Mode menu
In System menu, press M button to select Mode: XXXand press + or –button to enter the
password: +-MC+-, will pop up the below interface:
Figure.3.1.4.1 Mode menu
Gain: XXX Gain value, range: 0~+255;
Bright: XXX Brightness value, range: -2048~+2048;
Save: XXXSave configuration setup;
Exit: Exit configuration setup. Press MENU button until Exit option is selected and
press UP button or DOWN button to exit.
3.2. Main operation description
3.2.1. Focusing
When there is no menu displayed, press UP or DOWN button to adjust the focus, or press the UP
and DOWN buttons at the same time to do autofocus.
3.2.2. Single pixel correction setup
Press C button to do single pixel correction.
Note:
Camera will do single pixel correction automatically for several time when power on.
After start-up, since the camera is in thermal equilibrium processing, it may need single pixel
correction for several times. After about 45 minutes, the system reaches thermal equilibrium.
Mode: Gain: Bright: Save: Exit:

11
If so, the system usually has no need to do single pixel correction.
The camera running built-in calibration mechanism can do calibration anytime. Besides, it is
normal when you hear some “click”noise during calibration.
3.2.3. Auto imaging mode setup
Setup: Press MENU button until Auto: XXXis activated, press UP button or DOWN button to
select needed mode.
Exit: Press MENU button until Exit: option is selected and press UP button or DOWN button
to exit..
Note: There are three modes:
Auto 0: Manual gain, manual brightness. The camera will not adjust brightness and gain
automatically according to the observed object.
Auto 1: Manual gain, auto brightness. The camera adjusts brightness automatically according
to the observed object and you may adjust gain manually.
Auto 2: Auto gain, auto brightness. The camera can adjust both brightness and gain
automatically according to the observed object.
3.2.4. Imaging mode selection
Setup: Press MENU button until Mode: XXXis activated and press UP button or DOWN
button to select needed mode.
Exit: Press MENU button until Exit: option is selected and press UPbutton or DOWN button
to exit.
Note: The camera has ten modes under Auto: XXX mode, where 0,1 are fixed factory default and
2～9 are user-defined. Herein, user can only choose the mode but not able to adjust.

12
3.2.5. Gain setup
Setup: Press MENU button until G: XXX option is selected. Press UP button or DOWN
button to adjust gain parameter value.
Exit: Press MENU button until Exit: option is selected and press UP button or DOWN
button to exit.
Note: this function is only valid when the auto imaging mode setup is Auto 0 or Auto 1.In Auto
2 mode, gain is automatically adjusted. When pressing MENU button, menu will skip gain setup
option.
3.2.6. Brightness setup
Setup: Press MENU button until B: XXX option is selected. Press UP button or DOWN button
to adjust brightness parameter value.
Exit: Press MENU button until Exit:option is selected and press UP button or DOWN
button to exit.
Note: This function is only valid when the auto imaging mode setup is Auto 0. In Auto 1 and Auto
2, brightness is automatically adjusted. When pressing MENU button, menu option will skip
brightness adjustment option.
3.2.7. Polarity setup
Setup: Press MENU button until P: XXX is selected. Press UP button or DOWN button to
select black hot /white hot display mode.
Exit: Press MENU button until Exit:option is selected and press UP button or DOWN
button to exit.

13
3.2.8. Image enhancement setup
Setup: Press MENU button until E: XXX option is selected. Press UP button or DOWN
button to set needed enhancing state.
Exit: Press MENU button until Exit: option is selected and press UP button or DOWN
button to exit.
Note: Image enhancement can improve the observation effect, but may decrease the
Signal-to-Noise. This function is disabled in Mode 8.
3.2.9. Crosshair setup
Setup: Press MENU button until C: XXX menu option is activated; Press UP button or
DOWN button to setup needed enhancing state.
Exit: Press MENU button until Exit:option is selected and press UP button or DOWN
button to exit.
Note:
Set the calibration parameter if the images are non-uniformity
3.2.10. Dead pixel correction setup
Setup: Manually Setup: press F button and UP button at the same time to activate dead
pixel correction setup. Press UP button or DOWN button to move crosshair central
dot to dead pixel position, and then press C button (calibration function) to replace
current dead pixel (press Cbutton again to cancel).
Exit: Press MENU button to select Esc, and then press UPbutton to exit.
Note: If immovable dead pixel exists in the image, calibration can not be done by pressing C
button to activate dead pixel correction setup.

14
4. Troubleshooting
Please follow the below table to diagnose and solve the problem. If problem is still exited, please
contact our service center.
Trouble
Reasons and solutions
The camera can not power
on
Power cable is not connected correctly
→Connect the power cable again
Thermal camera protection procedure
→Wait for 10 seconds and turn on again
The camera powers off
automatically
The power cable connection is improper
→Connect the cable properly
No thermal images
The lens cover is not opened
→Open the lens cover
Switch between external power source and battery
→Reboot the camera

15
5. Technical specifications
Item
ThermalTronix
TT-1040S-UTCM
TT-1075S-UTCM
Detector
Detector type
Uncooled FPA micro bolometer
Array
size/format
384×288
Pixel size
25um
Wave range
8-14um
Focal length
40 mm
75mm
IFOV
13.7°×10.3°
7.3°×5.5°
NETD
≤100mK@30℃
Focus
Electric focusing
Frame rate
50HZ
Special
resolution
0.63mrad
0.33mrad
Measurements
Brightness/gain
Manual brightness/gain; Automatic brightness/manual gain;
Automatic brightness/gain
Automatic
brightness/gain
configuration
adjustment
2 fixed patterns, 8 user-defined modes
Polarity
reversal
Black hot/white hot
Electronic
zoom
2x
Noise reduction
Yes
Enhancement
Yes
Calibration
Automatic timing calibration
Cross division
Demonstration/hide away
Environment
requirement
Work
temperature
-20℃~ +55℃
Storage
temperature
-40℃~ +65℃
Encapsulation
IP40
Physical
characteristics
Weight
≤0.7kg
≤1kg
Dimensions
164mm×63mm×74mm
186mm×96mm×96mm

16
Power supply
Power
consumption
≤6W
Interface
External power
YES (DC12V±20%)
Video output
PAL
Communication
interface
RS485
Control
protocol
PELCO-D/PELCO-P/INTELLISYSTEM