Intellisystem ThermalTronix TT-L-UTCM Series User manual

ThermalTronix
TT-L-UTCM Series
Thermal Imaging Camera
User Manual

1
Warnings
Please avoid aiming the lens at extreme high temperature radiation source, such as the sun, molten
steel or laser in any situation; otherwise, the detector may be damaged.
Please do not touch the lens to avoid contaminating and damaging. Please pay attention to protect the
lens to avoid causing abrasion, scratches even breaches, otherwise, it will affect the device
performance badly, even damage the device.
This device is a precise optoelectronic product. Please protect it properly during usage, storage and
transportation, where improper use (such as drop and collision) will cause damage to the device. If the
internal connection is broken during the assembly process or the apparatus is damped (rain wet), the
performance will be reduced and even the device will be damaged.
Make sure that the power control connection is reliable. If the power control wire is in bad connection,
it will damage the device.
Ensure the proper connection of power control cable and data cable. Wrong connection may cause
damage to the device.
Do not swag fiercely or collide the device during transportation, otherwise it will cause
performance-reduction and even damage to it.
Please use the specified power supply; otherwise it will cause improper working, even damaging the
apparatus.
If the product works abnormally, please contact the dealer or the nearest after-sale service center. Please
do not dismantle or replace it in any manners.

2
Content
1. Overview ......................................................................................................................................... 3
1.1 Features:........................................................................................................................................ 3
1.2 Applications:.................................................................................................................................. 3
1.3 Accessories List:............................................................................................................................. 3
2. Appearance ..................................................................................................................................... 4
2.1 Interface definitions ...................................................................................................................... 4
2.2 Dimensions .................................................................................................................................... 5
2.3 Protocol setup ............................................................................................................................... 6
2.4 Function key chart................................................................................................................... 6
2.5 Guide for call the Preset................................................................................................................ 6
3. Operations....................................................................................................................................... 7
3.1 Main menu .................................................................................................................................... 7
3.2 Sub-menu operations.................................................................................................................... 9
3.3 COM sub-menu............................................................................................................................ 11
3.4 Mode sub menu .......................................................................................................................... 12
3.5 Alarm Valve sub-menu ................................................................................................................ 14
4. Specifications................................................................................................................................. 16
5. Troubleshooting ............................................................................................................................ 17

3
1. Overview
1.1 Features:
384*288 uncooled detector
2X Digital zoom
Black hot/White hot switch
Automatic/Manual calibration
PAL/NTSC mode video output
RS485 interface, support PELCO-D/PELCO-P protocol,
Thermalized, focus free lens
Multiple lens options (9mm/18mm/37mm/50mm)
1.2 Applications:
Road monitoring, perimeter guard, channel management, marine reconnaissance patrol, etc.
1.3 Accessories List:
Items
Quantity
Remark
Thermal camera
1
Carton
1
User manual
1
On the disk
DC12V Power Adapter
1
Optional
Lens
1
Optional

4
2. Appearance
2.1 Interface definitions
Back View

5
Definition List：
Item
Name
Instruction
Note
1
Video
Analog video
2
GND
Video GND
3
RS485-
RS485B
4
RS485+
RS485A
5
ALARM+
Alarm switch output
Open
6
ALARM-
Alarm switch output
7
GND
Power GND
8
DC+12V
DC12V input
2.2 Dimensions
Product outside dimension refer to illustration below

6
2.3 Protocol setup
Factory default：RS485、PELCO-D、baud 2400、add 1。
Protocol：PELCO-D/P
Baud：2400、4800、9600、19200
ADD：0~254
2.4 Function key chart
Camera Communication Default settings (RS485)-> Address:1 Baud:2400 Protocol: PELCO-D
2.5 Guide for call the Preset
A、call preset to popup the menu
Call preset 100 popup menus and press key “LENS-”to change the items
B、call preset to setup the alarm range
Call preset 101 to switch the alarm range
C、call preset to change the Protocol
Call preset 106 changes to PELCO-D
Call preset 107 changes to PELCO-P
D、call preset to change the Baud rate
LENS+
ZOOM+
Calibration
Up
Alarm switch
FOCUS-
ZOOM-
LENS-
Polarity
Down
Electrical zoom
FOCUS+

7
Call preset 108 changes to baud 2400
Call preset 109 changes to baud 4800
Call preset 110 changes to baud 9600
E、call preset to change the address of thermal camera
Call preset 111 to changes to address 1
Call preset 112 to changes to address 2
Call preset 113 to changes to address 13
……
Call preset 127 to changes to address 17
3. Operations
3.1 Main menu
Without the menu call preset 100. enter the main menu，pic 1：
2
3
4
5
6
7
8
1
Pic 1

8
Press key “LENS-” move the cursor ，Press key “FOCUS+” or “FOCUS-” to change the value where the
cursor is 。Auto save when exit
1、Auto: XXX Display the current image auto mode. Three options:
0: manual gain, manual brightness;
1: manual gain, auto brightness;
2: auto gain, auto brightness; （Factory default）
2、G: XXX Gain value, range: 1～1023；
3、B: XXX Brightness value, range
4、P: XXX White/black hot display mode
0: black hot 1: white hot
5、ZOOM：Y/N Zoom status
N：no zoom （default）Y：Zoom 2 times
6、Level：X show the level of alarm：From 1 to 6, default is 4
7、Setting: Press key “FOCUS+” or “FOCUS-”，show the password dialogue
Press “FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”to enter sub menu dialogue
8. EXIT: Exit the menu
Note ：
All parameters are save automatically after exit
The camera will run the last setup after reboot

9
3.2 Sub-menu operations
In the main menu, move the cursor to “Settings “option, press” Focus+”or “Focus-”show the
password dialogue，Input the password, refer to Pic 2
Press key ：“FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”，to enter ，refer to Pic 3：
Pic 2
2
3
4
5
6
7
8
1
Pic 3
9
10

10
Press key “LENS-” move the cursor ，Press key “FOCUS+” or “FOCUS-” to change the value where the
cursor is 。Auto save when exit
1、COM: press key “FOCUS+”or “FOCUS-”show the password dialogue，Input the password
“FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”enter the level 3 sub menu
2、Mode : press key “FOCUS+”or “FOCUS-”show the password dialogue，Input the password
“FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”enter the level 3 sub menu
3、Alarm Valve: press key “FOCUS+”or “FOCUS-”show the password dialogue，Input the
password “FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”enter the level 3 sub menu
4、Debug: press key “FOCUS+”or “FOCUS-”show the password dialogue，Input the password
“FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”enter the level 3 sub menu
5、Recover ：H/L/N Setup as H /L/N；
Setup as H：Calibrate 1 time during the 1 minute if working time less than 10
minutes. Calibrate 1 time during 2 minutes if working time between 10 and 30 minutes. calibrate 1
time during 5 minutes if working time between 30 minutes and 1 hour. Calibrate 1 time during 10
minutes if working time more than 1 hour. Calibrate 1 time during 20 minutes if working time more
than 2 hours.
Setup as L：Calibrate 1 time during the 1 minute if working time less than 0 minute.
Calibrate 1 time during 2 minutes if working time between 10 and 30 minutes. calibrate 1 time during 5
minutes if working time more than 30 minutes
Setup as /N：calibrate manually ；
6、Image: H/M/L setup as high/middle/low；
Each grade relatively corresponds to a value. It could be setup in the TEST menu .default is
middle

11
7、Alarm：Xshow the status of gray alarm ：N/Y
N: off；（ Default）Y: On
8、E：XShow the status of image enhancement，setup as C/1/2；
C: Close；（ default）1/2：Open relatively Gain grade
9、Backup：factory default ，including auto，polarity，alarm range，calibration，image，
alarm，alarm pixel Number。
10、Exit ：XXX press key “FOCUS+” or “FOCUS-”to exit
3.3 COM sub-menu
First：； Without the menu call preset 100. Enter the main menu. In the main menu, press the key “LENS-
“move the cursor to “setup”，press key “FOCUS+”or “FOCUS-”show the password dialogue，Input the
password. “FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”enter the sub menu
Second：After login Sub-menu. press the key “LENS- “move the cursor to “COM”key. press key “FOCUS+”
or “FOCUS-”show the password dialogue，Input the password. “FOCUS+、FOCUS-、FOCUS+、FOCUS-、
FOCUS+、FOCUS-”enter the level 3 sub menu. Refer to Pic 4

12
In the menu “COM” ，Press key “LENS-” move the cursor ，Press key “FOCUS+” or “FOCUS-” to change the
value where the cursor is 。Auto save when exit
1、ID：XXX ADD：0~254。
2、BaudRate：XXXBaud :1200,2400,4800,9600,14400,19200,38400。
3、Protocol：PELCO-D/P。
4、Exit：Press key LENS+ to exit
Default：Add:1 Baud:2400 Protocol: PELCO-D
3.4 Mode sub menu
First：Without the menu call preset 100. Enter the main menu. In the main menu, press the key “LENS-
“move the cursor to “setting”，press key “FOCUS+”or “FOCUS-”show the password dialogue，Input the
1
2
3
4
Pic 4

13
password. “FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”enter the sub menu
Second：：After login Sub-menu. press the key “LENS- “move the cursor to “Mode”key. press key “FOCUS+”
or “FOCUS-”show the password dialogue，Input the password. “FOCUS+、FOCUS-、FOCUS+、FOCUS-、
FOCUS+、FOCUS-”enter the level 3 sub menu. Refer to Pic 5
In the menu “Mode”，Press key “LENS-” move the cursor ，Press key “FOCUS+” or “FOCUS-” to change
the value where the cursor is 。Auto save when exit
1、Gain：XXX Range: 0~255。
2、Bright：XXX Range :0~255。
3、Exit：Press key LENS+ to exit
Default：G:32 B:188
1
2
3
Pic5

14
3.5 Alarm Valve sub-menu
First：Without the menu call preset 100. Enter the main menu. In the main menu, press the key “LENS-
“move the cursor to “setup”，press key “FOCUS+”or “FOCUS-”show the password dialogue，Input the
password. “FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”enter the sub menu
Second：After login Sub-menu. press the key “LENS- “move the cursor to “Alarm Valve”key. press key
“FOCUS+”or “FOCUS-”show the password dialogue，Input the password. “FOCUS+、FOCUS-、FOCUS+、
FOCUS-、FOCUS+、FOCUS-”enter the level 3 sub menu.；Refer to pic 6：
In the menu “Alarm Valve”，Press key “LENS-” move the cursor ，Press key “FOCUS+” or “FOCUS-” to
change the value where the cursor is 。Auto save when exit
1、Level：XRange: 1~6。
2、Threshold：XXX Show the status of Alarm Valve 。
1
2
3
4
Pic 6

15
3、AlarmPIX：XXX 。Show and setup for minimum pixel number of alarm.
Such as alarm Number 2 .so the alarm pixel is 2* 2. totally 4 pixels
4、Exit：Press key LENS+ to exit。
Default: Alarm range and alarm valve :(grade 1: 650, relatively temperature difference is 30 ℃; Grade
2:1050, relatively temperature difference is 45 ℃; Grade 3:1450, relatively temperature difference is
60 ℃; Grade 4:2100, relatively temperature difference is 80 ℃; Grade 5:2800, relatively temperature
difference is 100 ℃; Grade 6:3600, relatively temperature difference is 120 ℃) alarm pixel number :1

16
4. Specifications
Items
ThermalTronix TT-L-UTCM Series
TT-1009L-UTCM
TT-1018L-UTCM
TT-1037L-UTCM
TT-1050L-UTCM
Detector
characteristics
Detector type
Uncooled FPA microbolometer
Array size
384×288
Pixel
25um
Spectral range
8～14um
Frame rate
50HZ
Lens
Focal length
9mm
18mm
37mm
50mm
F number
F1.1
Focus
A thermalized, focus-free
Free focus range
0.8m~∞
3m~∞
12m~∞
23m~∞
NETD
≤100mK
Gain/Brightness
adjustment
Manual brightness/gain; auto brightness/manual gain; auto brightness/gain
Functions
Polarity inversion
White/black hot mode
Digital zoom
2X
Calibration
Automatic/manual
Grayscale alarm
Yes
Interface
External power
DC10V-15V
Power consumption
≤2.2W
Video output
PAL
Remote control
interface
RS485, PELCO-D/P Protocol
Environment
Operation
temperature
-20℃~ +50℃, up to (-40℃~ +60℃)
Storage temperature
-40℃~ +70℃
Weight（g）
≤350
≤350
≤400
≤520
Size（mm）
56*54*92
56*54*92
56*54*100
60*60*112
Note: Specifications are subject to change without notice

17
5. Troubleshooting
Please follow the below table to diagnose and solve the problem. If problem is still exited, please contact
our service center.
Trouble
Reasons and solutions
The camera can not power
on
Power cable is not connected correctly
→Connect the power cable again
Thermal camera protection procedure
→Wait for 5 seconds and turn on again
The camera powers off
automatically
The power cable connection is improper
→Connect the cable properly
No thermal images
The lens cover is not opened
→Open the lens cover
Switch between external power source and battery
→Reboot the camera