Intellisystem ThermalTronix TT-CXL-DVACS Series User manual

0
ThermalTronix
TT-CXL-DVACS Series
Thermal Camera Specifications
User Manual

1
Restriction
Intellisystem Technologies shall reserve copyright of document. Under no circumstances, this document
shall be reproduced, distributed or changed, partially or wholly, without formal authorization of
Intellisystem Technologies.
Disclaimer
Intellisystem Technologies makes the best to verify the integrity and correctness of the contents in this
document, but no formal guarantee shall be provided. Use of this document and the subsequent results
shall be entirely on the user's own responsibility. Intellisystem Technologies shall have the right to change
the contents of this manual without prior notice for the purpose of enhanced performance.
Warranty
If the product does not operate properly in normal conditions, please let us know. Intellisystem
Technologies will resolve the problem for free of charge. The warranty period is 1 years. However, the
followings are excluded:
If the system behaves abnormally because you run a program irrelevant to the system operation.
Deteriorated performance or natural worn-out in process of time.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.

2
Warnings
Please avoid aiming the lens at extreme high temperature radiation source, such as the sun, molten
steel or laser in any situation; otherwise the detector may be damaged.
Please do not touch the lens to avoid contaminating and damaging. Please pay attention to protect
the lens to avoid causing abrasion, scratches even breaches, otherwise, it will affect the device
performance badly, even damage the device.
This device is a precise optoelectronic product. Please protect it properly during usage, storage and
transportation, where improper use (such as drop and collision) will cause damage to the device.
Make sure that the power control connection is reliable. If the power control wire is in bad
connection, it will damage the device.
Ensure the proper connection of power control cable and data cable. Wrong connection may cause
damage to the device.
Do not swag fiercely or collide the device during transportation, otherwise it will cause
performance-reduction and even damage to it.
If the product works abnormally, please contact the dealer or the nearest after-sale service center. Please
do not dismantle or replace it in any manners.

3
Content
1Introduction ................................................................................................................................. 4
1.1 Features ..................................................................................................................................... 4
1.2 Included ..................................................................................................................................... 5
2 Component names and function .................................................................................................... 6
2.1 Device appearance ..................................................................................................................... 6
2.2 Connector definition .................................................................................................................. 6
3Operation Guide............................................................................................................................. 7
3.1 Communication parameters....................................................................................................... 7
3.2 Thermal camera control key description .................................................................................... 7
3.3 CCD camera keys description ..................................................................................................... 7
4Thermal imaging camera menu...................................................................................................... 8
4.1 Main-menu operation ................................................................................................................ 8
4.2 Setting secondary menu ........................................................................................................... 10
4.3 Com sub-menu ......................................................................................................................... 12
4.4 Mode sub-menu....................................................................................................................... 13
4.5 Alarm Value sub-menu ............................................................................................................. 14
5Change the address of PT system ................................................................................................. 15
6Change the address of CCD camera.............................................................................................. 16
7Change the address of protocol board ......................................................................................... 17
8Troubleshooting ......................................................................................................................... 18
9Technical specifications.............................................................................................................. 19

4
1Introduction
TT-CXL-DVACS Series is composed of uncooled infrared thermal imaging module and visible light
camera, which can be applied in the following fields: middle-range power stations, public places;
short-range gate of entry and exit, equipment storage sites; day and night to monitor people , vehicles,
ships and so on.
1.1 FEATURES
Thermal camera
Fixed athermalized lens
AUTO calibration
Manual or Automatic brightness/gain adjustment
Image Noise Reduction function: reduce Image background noise
Image enhancing function : enhance the ability to detect small object
CCD camera
With the state-of-the-art digital signal processing technology, full digital image processing and
special algorithm of 600-line high resolution implemented.
High Sensitivity: It implements images of high sensitivity using the up-to–date Super-HAD
CCD.
High performance surveillance camera, 25X optical zoom and 16X digital zoom
PTZ
Preset：80 presets can be setup
Support 0°~360°(pan) continuous rotation
Top load of tilt is ±90°
RS485, support PELCO-D/PELCO-P protocol
IP66,full weatherproof

5
1.2 INCLUDED
TT-CXL-DVACS Series List for accessories and files：
accessory
quantity
remark
PTZ Camera
1
AC24 Power Adapter
1
User manual
1
Packing list
1
qualification
1

6
2 Component names and function
2.1 Device appearance
Pic. 1
No.
Description
Remark
1
Thermal housing
Thermal camera
2
Rear cover
Address and function of PTZ DIP switch
3
CCD housing
Include CCD camera and protocol board
4
DIP switch cover
Definition refers to chapter 5
5
Wire hole
Used to connect power supply, monitor and RS485 control
2.2 Connector definition
The control wire is from bottom of PT system.
Definition as follows:
No.
Description
Remark
1
RS485
RS485+
2
RS485-
4
CCD Video
Analog video output of CCD camera
5
IR Video
Analog video output of thermal imaging camera
6
AC24V
Power supply
7
GND

7
3OPERATION GUIDE
3.1 Communication parameters
Thermal camera default address：PELCO-D、baud 9600、address 2
PT system default address：PELCO-D、baud 9600、address 1
Visual camera default address：PELCO-D、baud 9600、address 1
Protocol board address：PELCO-D、baud 9600、address 1
3.2 Thermal camera control key description
Before the operation. Pls set address 2 firstly.
3.3 CCD camera keys description
Before the operation, pls set address 1 firstly
Operational keys
Function
Up
PTZ up
Down
PTZ down
Left
PTZ left
Right
PTZ right
FOCUS-
Near Focus
FOCUS+
Far Focus
ZOOM-
Zoom out
ZOOM+
Zoom in
LENS+
ZOOM+
Calibration
Up
Alarm switch
FOCUS-
ZOOM-
LENS-
Polarity
Down
Digital Zoom
FOCUS+

8
4Thermal imaging camera menu
4.1 Main-menu operation
Before operate thermal camera .please set address 2 firstly
Without the menu call preset 100 to activate the main menu. Enter the main menu(pic 2)：
Press key “LENS-” move the cursor，Press key “FOCUS+” or “FOCUS-” to change the value where the cursor
is. Auto save when exit
1、Auto: XXX Display the current image auto mode. Three options:
0: manual gain, manual brightness;
1: manual gain, auto brightness;
2: auto gain, auto brightness;（Factory default）
2、G: XXX Gain value, range: 1～1023；
3、B: XXX Brightness value, range
4、P: XXX White/black hot display mode
0: black hot 1: white hot
5、Z：Y/N Zoom status
2
3
4
5
6
7
8
1
Pic 2

9
N：no zoom （default）Y：2X digital zoom
6、Level：Xshow the range of alarm：From 1 to 6, default is 4
7、Seting : Activate the setting secondary menu
Press key “FOCUS+” or “FOCUS-”，show the password dialogue
Press “FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”to enter setting menu
dialogue. This password is suitable for all the password dialogue box in the thermal
imaging camera
8、EXIT : Press key “FOCUS+” or “FOCUS-” to exit
Note ：
All parameters are save automatically after exit
The camera will run the last setup after reboot

10
4.2 Setting secondary menu
In the main menu, move the cursor to “setting” ，press key “FOCUS+” or “FOCUS-” show the password
dialogue，refer to Pic 3, Input the password to enter, refer to Pic 4.
Press key “LENS-” move the cursor, press key “FOCUS+” or “FOCUS-” to change the value or get into the
submenu where the cursor is 。Auto save when exit
1、COM: Setup the communication parameters.
2、Mode : Setup the mode parameters.
3、AValue: Setup the alarm parameters.
Pic 3
2
3
4
5
6
7
8
1
Pic 4
9
10

11
4、Debug: Debug option only for R&D department of manufacturer
5、RECOVER ：H/L/N Setup as H /L/N；
Setup as H：Calibrate 1 time during the 1 minute if working time less than 10
minutes. Calibrate 1 time during 2 minutes if working time between 10 and 30 minutes .calibrate 1
time during 5 minutes if working time between 30 minutes and 1 hour. Calibrate 1 time during 10
minutes if working time more than 1 hour. Calibrate 1 time during 20 minutes if working time more
than 2 hours.
Setup as L：Calibrate 1 time during the 1 minute if working time less than 0 minute.
Calibrate 1 time during 2 minutes if working time between 10 and 30 minutes .calibrate 1 time during 5
minutes if working time more than 30 minutes
Setup as /N：calibrate manually ；
6、Image: high/middle/low setup as high/middle/low；
Each grade relatively corresponds to a value. It could be setup in the TEST menu .default is
middle
7、Alarm：XShow the status of gray alarm ：N/Y
N: off；（ Default）Y: On
8、E：XShow the status of image enhancement，setup as C/ 1/2
C:Close；（ default）1/2：Open relatively enhancement grade
9、Backup：Factory default
10、Exit ：XXX Press key “FOCUS+” or “FOCUS-” to exit

12
4.3 Com sub-menu
In the menu “COM”(chapter 4.2 shows how to activate the “com” option)，Press key “LENS-” move the
cursor ，Press key “FOCUS+” or “FOCUS-” to change the value where the cursor is. Refer to Pic 5. Auto
save when exit
1、ID：XXX Address of the IR camera：0~254。
2、BauRate：XXXBaud :1200,2400,4800,9600,14400,19200,38400。
3、Protocol：PELCO-D/PELCO-P。
4、Exit：Press key “LENS+”to exit
Default：Add:1 Baud:9600 Protocol: PELCO-D
1
2
3
4
Pic 5

13
4.4 Mode sub-menu
In the menu “Mode”(chapter 4.2 shows how to activate the “Mode” option)，Press key “LENS-” move the
cursor ，Press key “FOCUS+” or “FOCUS-” to change the value where the cursor is. Refer to Pic 6.Auto
save when exit
1、Gain：XXX Range: 0~255。
2、Bright：XXX Range :0~255。
3、Exit：Press key “LENS+”to exit
Default：Gain:32 Bright:188
1
2
3
Pic 6

14
4.5 Alarm Value sub-menu
In the menu “Avalue”(chapter 4.2 shows how to activate the “Avalue” option)，Press key “LENS-”
move the cursor ，Press key “FOCUS+” or “FOCUS-” to change the value where the cursor is. Refer to
Pic 7.Auto save when exit
1、Level：XRange: 1~6。
2、Threshold：XXX Show the status of Alarm Valve 。
3、AlarmPIX：XXX minimum pixels of alarm.
Such as alarm Number 2 .so the alarm pixel is 2* 2 .totally 4 pixels
4、Exit：Press key LENS+ to exit。
Default: Level and Threshold :(Level 1: 650, relatively temperature difference is 30 ℃. Level 2:1050,
relatively temperature difference is 45 ℃, Level 3:1450, relatively temperature difference is 60 ℃, Level
4:2100, relatively temperature difference is 80 ℃, Level 5:2800, relatively temperature difference is
100 ℃, Level 5:3600, relatively temperature difference is 120℃) AlarmPIX :1
1
2
3
4
Pic 7

15
5 Change the address of PT system
PT System address is minus 1 of thermal camera.
Use a Phillips screwdriver to loosen four Phillips Screws on the DIP switch cover (refer to Pic.1), remove
the DIP switch cover, you can see the circuit board DIP switch as shown in Pic8.
SW1 SW2
Pic8
Note ：1. address switch (SW1）
2. function switch (SW2）,pls contact our technical support to get the definition of SW2
Address switch（SW1）is for PTZ communication address (ID), using eight binary coding system ranges from
1 to 255, specific DIP rules please refer to table below.
Note: when setup address dip, please cut off the power supply. Or else, it will not identify.
Address
No.1
No.2
No.3
No.4
No.5
No.6
No.7
No.8
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
5
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
6
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
7
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
8
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
....
.........................................
254
OFF
ON
ON
ON
ON
ON
ON
ON
255
ON
ON
ON
ON
ON
ON
ON
ON

16
6 Change the address of CCD camera
CCD camera address is minus 1 of thermal camera, it means CCD camera has the same address as PT
system
Open housing of CCD camera. Pressing the 『SETUP』button(refer to Pic 9) on the rear of CCD camera
about 2 seconds to popup the menu of the camera. Refer to Pic 10
Pic 9 Pic 10
Pressing 『SETUP』switch (up or down),move up or down on the menu to “COMMUNICATION”.
And press 『SETUP』switch to enter “COMMUNICATION” menu, shown as Pic.11.
1.Protocol Must be PELCO-D; otherwise the CCD camera
cannot be controlled.
2.BaudRate Must be 9600; otherwise the CCD imaging camera
cannot be controlled.
3.ADDRESS Setup the camera’s address.
Moving cursor to and pressing 『SETUP』switch to exit the
menu. Before exiting the setup screen, select 『SAVE』to save your settings. Pic.11

17
7 Change the address of protocol board
Same with the PT system address.
Only reboot the address will be valid after change address.
The address switch is interface J3 on the protocol circuit board(Refer to Fig.12) which installed in the CCD
camera housing (Refer to Pic.1). Refer to Fig.12
Pic.12 Pic.13
J3 interface address switch from left to right is note as 1 2 3 4 bit. Up means off, down means on
Address
No.1
No.2
No.3
No.4
1
ON
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
3
ON
ON
OFF
OFF
4
OFF
OFF
ON
OFF
5
ON
OFF
ON
OFF
6
OFF
ON
ON
OFF
7
ON
ON
ON
OFF
8
OFF
OFF
OFF
ON
..........
15
ON
ON
ON
ON

18
8Troubleshooting
Please follow the below table to diagnose and solve the problem. If problem is still exited, please
contact our service center.
Trouble
Possible cause
Solution
After power-on, PTZ
does not perform
self-checking
Power wire connects wrong or
not well
Again connect the power wire
PT system is broken
Change the PT system
after power on .the PT
self-check successful but
cannot operate
Address of PT is not right
Change the address of PT
system refer to 4.2
The address of PT and
protocol must be same
Address of protocol board is
not right
change the protocol board
address again refer to 4.4
The address of PT and
protocol must be same
Cannot operate the thermal
camera
Address of thermal camera is
not right
change the address of thermal
camera refer to 4.1
Protocol address is minus 1 of
thermal camera address
Protocol and baud rate of
thermal camera is not right
The baud rate of thermal
camera is 9600
The protocol of thermal
camera is PELCO-D
Cannot operate the visual
camera
CCD address is not right
Change the address of Visual
camera refer to 4.3
The address of Visual camera
must same with protocol
board address
Cannot capture the image of
camera when PT is rotating
Power consumption is not
enough
Apply the right power supply
Video wire connects not well
Check the video wire
connection

19
9Technical specifications
Items
ThermalTronix TT-CXL-DVACS Series
Thermal Imaging
Camera
Detector characteristics
Detector type
Un-cooled FPA micro-bolometer
Resolution
384*288
Detector pitch
25μm
Frame rate
50HZ
Image characteristics
Lens
TT-C1009XL-DVACS
f=9mm
TT-C1018XL-DVACS
f=18mm
TT-C1037XL-DVACS
f=37mm
TT-C1050XL-DVACS
f=50mm
NETD
≤100mk
Focus Range
Athermalized, focus-free
Functions
Brightness/gain
control
Manual brightness/gain; Automatic brightness/manual
gain; Automatic brightness/gain
Automatic
brightness/gain
configuration
adjustment
2 fixed patterns, 8 users from definition establishment
pattern
Polarity reversal
Black hot/white hot
Electronic zoom
2x
Noise reduction
function
Yes
Image
intensification
function
Yes
Calibration
Automatic calibration
CCD Camera
Resolution
Total pixels 795(H)x596(V), Effective pixels 752(H)x582(V)
Imaging Device
1/4″Super HAD CCD
lens
3.66-91.36mm(F1.65-3.0), 25x optics, 16x digital
PTZ
Horizontal
Resolution
Color: 600TV lines, B/W:700TV lines
Horizontal rotation
degrees
0° ~360° continuous rotation
vertical rotation
degrees
-90°～+90°
Horizontal rotation
speed
0.01°～60°/S
vertical rotation
speed
0.01°～30°/S
Heater
YES
Fan
YES
Power supply
Voltage
AC24V
Power
Consumption
<250W（including heating）
Environment
Operating
temperature
-20℃~+55℃
Storage
temperature
-45℃~+70℃
Protection
IP66
Physical
characteristics
Weight
≤17Kg
Dimensions
322mm(W)×470mm(H)×268mm(D)
Interface
Input voltage
AC24V
Analog video
2 BNC, PAL
Serial port
RS485 (PELCO-D/PELCO-P)