Intellisystem ThermalTronix TT-L-BFTC Series User manual

0
ThermalTronix
TT-L-BFTC Series
Thermal Imaging Camera
User Manual

1
Warnings
Please avoid aiming the lens at extreme high temperature radiation source, such as the sun, molten
steel or laser in any situation; otherwise the detector may be damaged.
Please do not touch the lens to avoid contaminating and damaging. Please pay attention to protect the
lens to avoid causing abrasion, scratches even breaches, otherwise, it will affect the device
performance badly, even damage the device.
This device is a precise optoelectronic product. Please protect it properly during usage, storage and
transportation, where improper use (such as drop and collision) will cause damage to the device. If the
internal connection is broken during the assembly process or the apparatus is damped (rain wet), the
performance will be reduced and even the device will be damaged.
Make sure that the power control connection is reliable. If the power control wire is in bad connection,
it will damage the device.
Ensure the proper connection of power control cable and data cable. Wrong connection may cause
damage to the device.
Do not swag fiercely or collide the device during transportation, otherwise it will cause
performance-reduction and even damage to it.
Please use the specified power supply; otherwise it will cause improper working, even damaging the
apparatus.
If the product works abnormally, please contact the dealer or the nearest after-sale service center. Please
do not dismantle or replace it in any manners.

2
Contents
1. Overview.......................................................................................................................................... 3
1.1 Features:........................................................................................................................................ 3
1.2 Applications:.................................................................................................................................. 3
1.3 Interface definition........................................................................................................................ 3
1.4 Protocol setup ............................................................................................................................... 4
1.5 Function key chart......................................................................................................................... 4
1.6 Guide for call the Preset................................................................................................................ 4
2. Operations....................................................................................................................................... 6
2.1 Main menu .................................................................................................................................... 6
2.2 Sub-menu operations.................................................................................................................... 7
2.3 COM sub-menu ............................................................................................................................. 9
2.4 Configuration sub menu.............................................................................................................. 10
2.5 Alarm Valve sub-menu ................................................................................................................ 11
3. Specifications................................................................................................................................. 13

3
1. Overview
1.1 Features:
384*288 uncooled detector
2X Digital zoom
Black hot/White hot switch
Automatic/Manual calibration
PAL/NTSC mode video output
RS485 interface, support PELCO-D/PELCO-P protocol
Athermalized, focus free lens
Weatherproof, IP66
1.2 Applications:
Road monitoring, perimeter guard, channel management, marine reconnaissance patrol, etc.
1.3 Interface definition
The control wire is from gland seal plug of housing.
Definition as follows:
No.
Description
Remark
1
RS485
RS485+
2
RS485-
5
IR Video
Analog video output of thermal imaging camera
6
DC12V
Power supply
7

4
1.4 Protocol setup
Factory default：RS485、PELCO-D、baud 2400、add 1。
Protocol：PELCO-D/P
Baud：2400、4800、9600、19200
ADD：0~254
1.5 Function key chart
Camera Communication Default settings (RS485)-> Address:1 Baud:2400 Protocol: PELCO-D
1.6 Guide for call the Preset
A、call preset to popup the menu
Call preset 100 popup menus and press key “LENS-”to change the items
B、call preset to setup the alarm range
Call preset 101 to switch the alarm range
C、call preset to change the Protocol
Call preset 106 changes to PELCO-D
Call preset 107 changes to PELCO-P
D、call preset to change the Baud rate
Call preset 108 changes to baud 2400
LENS+
ZOOM+
Calibration
Up
Alarm switch
FOCUS-
ZOOM-
LENS-
Polarity
Down
Electrical zoom
FOCUS+

5
Call preset 109 changes to baud 4800
Call preset 110 changes to baud 9600
E、call preset to change the address of thermal camera
Call preset 111 to changes to address 1
Call preset 112 to changes to address 2
Call preset 113 to changes to address 13
……
Call preset 127 to changes to address 17

6
2. Operations
2.1 Main menu
Without the menu call preset 100. enter the main menu，pic 1：
Press key “LENS-” move the cursor ，Press key “FOCUS+” or “FOCUS-” to change the value where the
cursor is 。Auto save when exit
1、Auto: XXX Display the current image auto mode. Three options:
0: manual gain, manual brightness;
1: manual gain, auto brightness;
2: auto gain, auto brightness;（Factory default）
2、G: XXX Gain value, range: 1～1023；
3、B: XXX Brightness value, range
4、P: XXX White/black hot display mode
2
3
4
5
6
7
8
1
Pic 1

7
0: black hot 1: white hot
5、ZOOM：Y/N Zoom status
N：no zoom（default）Y：Zoom 2 times
6、Alarm range：X show the range of alarm：From 1 to 6, default is 4
7、Setup : Press key “FOCUS+” or “FOCUS-”，show the password dialogue
Press “FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”to enter sub menu dialogue
Note ：
All parameters are save automatically after exit
The camera will run the last setup after reboot
2.2 Sub-menu operations
In the main menu, move the cursor to “setup”，press key “FOCUS+”or “FOCUS-”show the password
dialogue，Input the password ，refer to Pic 2
Press key ：“FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”，to enter ，refer to Pic 3：
Pic 2

8
Press key “LENS-” move the cursor ，Press key “FOCUS+” or “FOCUS-” to change the value where the
cursor is 。Auto save when exit
1、COM: press key “FOCUS+”or “FOCUS-”show the password dialogue，Input the password
“FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”enter the level 3 sub menu
2、Configuration : press key “FOCUS+”or “FOCUS-”show the password dialogue，Input the
password “FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”enter the level 3 sub menu
3、Alarm Valve: press key “FOCUS+”or “FOCUS-”show the password dialogue，Input the
password “FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”enter the level 3 sub menu
4、Test: press key “FOCUS+”or “FOCUS-”show the password dialogue，Input the password
“FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”enter the level 3 sub menu
5、Calibration ：long/short/close Setup as long /short/close；
Setup as long：Calibrate 1 time during the 1 minute if working time less than 10 minutes. Calibrate 1
time during 2 minutes if working time between 10 and 30 minutes .calibrate 1 time during 5 minutes
if working time between 30 minutes and 1 hour. Calibrate 1 time during 10 minutes if working time
more than 1 hour. Calibrate 1 time during 20 minutes if working time more than 2 hours.
2
3
4
5
6
7
8
1
Pic 3
9
10

9
Setup as short：Calibrate 1 time during the 1 minute if working time less than 0 minute. Calibrate 1 time
during 2 minutes if working time between 10 and 30 minutes .calibrate 1 time during 5 minutes if working
time more than 30 minutes
Setup as /close：calibrate manually ；
6、Image: high/middle/low setup as high/middle/low；
Each grade relatively corresponds to a value. It could be setup in the TEST menu .default is middle
7、Alarm：Xshow the status of gray alarm ：N/Y
N: off；（ Default）Y: On
8、Gain：XShow the status of Gain，setup as C/1/2；
C: Close；（ default）1/2：Open relatively Gain grade
9、Default：factory default ，including auto，polarity，alarm range，calibration，image，
alarm，alarm pixel Number。
10、Exit ：XXX press key “FOCUS+” or “FOCUS-”to exit
2.3 COM sub-menu
First：； Without the menu call preset 100. Enter the main menu. In the main menu, press the key
“LENS-“ move the cursor to “setup”，press key “FOCUS+”or “FOCUS-”show the password dialogue，Input
the password. “FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”enter the sub menu
Second：After login Sub-menu. press the key “LENS-“ move the cursor to “COM”key .press key “FOCUS+”
or “FOCUS-”show the password dialogue，Input the password. “FOCUS+、FOCUS-、FOCUS+、FOCUS-、
FOCUS+、FOCUS-”enter the level 3 sub menu .Refer to Pic 4

10
In the menu “COM”, ，Press key “LENS-” move the cursor ，Press key “FOCUS+” or “FOCUS-” to change the
value where the cursor is 。Auto save when exit
1、Add：XXX ADD：0~254。
2、Baud：XXXBaud :1200,2400,4800,9600,14400,19200,38400。
3、Protocol：PELCO-D/P。
4、Exit：Press key LENS+ to exit
Default：Add:1 Baud:2400 Protocol: PELCO-D
2.4 Configuration sub menu
First：Without the menu call preset 100. Enter the main menu. In the main menu, press the key
“LENS-“ move the cursor to “setup”，press key “FOCUS+”or “FOCUS-”show the password dialogue，Input
the password. “FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”enter the sub menu
Second：： After login Sub-menu. press the key “LENS-“ move the cursor to “Configuration”key .press key
1
2
3
4
Pic 4

11
“FOCUS+”or “FOCUS-”show the password dialogue，Input the password. “FOCUS+、FOCUS-、FOCUS+、
FOCUS-、FOCUS+、FOCUS-”enter the level 3 sub menu. Refer to Pic 5
In the menu “Configuration”，Press key “LENS-” move the cursor ，Press key “FOCUS+” or “FOCUS-” to
change the value where the cursor is 。Auto save when exit
1、G：XXX Range: 0~255。
2、B：XXX Range: 0~255。
3、Exit：Press key LENS+ to exit
Default：G:32 B: 188
2.5 Alarm Valve sub-menu
First：Without the menu call preset 100. Enter the main menu. In the main menu, press the key
“LENS-“ move the cursor to “setup”，press key “FOCUS+”or “FOCUS-”show the password dialogue，Input
the password. “FOCUS+、FOCUS-、FOCUS+、FOCUS-、FOCUS+、FOCUS-”enter the sub menu
1
2
3
Pic5

12
Second：After login Sub-menu. press the key “LENS-“ move the cursor to “Alarm Valve”key .press key
“FOCUS+”or “FOCUS-”show the password dialogue，Input the password. “FOCUS+、FOCUS-、FOCUS+、
FOCUS-、FOCUS+、FOCUS-”enter the level 3 sub menu.；Refer to pic 6：
In the menu “Alarm Valve”, ，Press key “LENS-” move the cursor ，Press key “FOCUS+” or “FOCUS-” to
change the value where the cursor is 。Auto save when exit
1、Alarm range：XRange: 1~6。
2、Alarm Valve：XXX Show the status of Alarm Valve 。
3、Alarm pixel Number：XXX 。Show and setup for minimum l number of alarm.
Such as alarm Number 2 .so the alarm pixel is 2* 2 .totally 4 pixels
4、Exit：Press key LENS+ to exit。
Default: Alarm range and alarm valve :(grade 1: 650, relatively temperature difference is 30 ℃;Grade
2:1050, relatively temperature difference is 45 ℃;Grade 3:1450, relatively temperature difference is
60 ℃;Grade 4:2100, relatively temperature difference is 80 ℃;Grade 5:2800, relatively temperature
1
2
3
4
Pic 6

13
difference is 100 ℃; Grade 6:3600, relatively temperature difference is 120 ℃) alarm pixel number :1.
3. Specifications
Items
ThermalTronix
TT-1009L-BFTC
TT-1018L-BFTC
TT-1037L-BFTC
TT-1050L-BFTC
Detector
characteristics
Detector type
Uncooled FPA microbolometer
Array size
384×288
Pixel
25um
Spectral range
8～14um
Frame rate
50HZ
Lens
Focal length
9mm
18mm
37mm
50mm
F number
F1.1
Focus
Athermalized, focus-free
Free focus
range
0.8m~∞
3m~∞
12m~∞
23m~∞
NETD
≤100mK
Gain/Brightness
adjustment
Manual brightness/gain; auto brightness/manual gain; auto brightness/gain
Functions
Polarity
inversion
White/black hot mode
Digital zoom
2X
Calibration
Automatic/manual
Grayscale alarm
Yes
Interface
External power
DC10V-15V
Power
consumption
≤2.2W
Video output
PAL
Remote control
interface
RS485，PELCO-D/P Protocol
Environment
Operation
temperature
-20℃~ +50℃
Storage
temperature
-40℃~ +70℃
Weight
≤3KG
Size（mm）
362*140*145
Note: Specifications are subject to change without notice