Interlogix TVB-1101 User manual

TruVision IP Camera
Installation Guide
P/N 1072668A-EN • REV 1.0 • ISS 24SEP13

Copyright © 2013 UTC Fire & Security Americas Corporation,
Inc.
Interlogix is part of UTC Climate Controls & Security, a
unit of United Technologies Corporation. All rights
reserved.
Trademarks and
patents
The TruVision name and logo are trademarks of United
Technologies.
Other trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective products.
Manufacturer UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923,
USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
N4131
FCC compliance Class A: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in
a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
ACMA compliance Notice! This is a Class A product. In a domestic
environment this product may cause radio interference

in which case the user may be required to take
adequate measures.
Canada This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à
la norme NMB-0330 du Canada.
European Union
directives
12004/108/EC (EMC directive): Hereby, UTC Fire &
Security declares that this device is in compliance with
the essential requirements and other relevant
provisions of Directive 2004/108/EC.
2002/96/EC (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon
the purchase of equivalent new equipment, or dispose
of it at designated collection points. For more
information see: www.recyclethis.info.
Contact information For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.

Installation Guide 5
Content
Introduction 6
Product overview 6
Installation 7
Installation environment 7
Package contents 8
Cable requirements 8
Camera description 9
Setting up the camera 12
Accessing the SD card 13
Mounting the bullet camera 13
Mounting the VF dome camera 15
Mounting the indoor mini dome camera 19
Mounting the wedge dome camera 21
Using the camera with an Interlogix NVR or Hybrid DVR or
another system 22
Using the camera with TruVision Navigator 22
Specifications 23
TruVision IP bullet cameras 23
TruVision IP indoor mini dome 23
TruVision IP wedge cameras 24
TruVision IP VF mini dome cameras 24
Pin definitions 25

6 Installation Guide
Introduction
Product overview
This is the installation guide for TruVision IP camera models:
TVB-1101 (1.3MPX IP bullet camera, PAL)
TVB-3101 (1.3MPX IP bullet camera, NTSC)
TVB-1102 (3MPX IP bullet camera, PAL)
TVB-3102 (3MPX IP bullet camera, NTSC)
TVD-1103 (1.3MPX IP VF mini dome, PAL)
TVD-3103 (1.3MPX IP VF mini dome, NTSC)
TVD-1104 (3MPX IP VF mini dome, PAL)
TVD-3104 (3MPX IP VF mini dome, NTSC)
TVD-1101 (1.3MPX IP indoor mini dome, PAL)
TVD-3101 (1.3MPX IP indoor mini dome, NTSC)
TVD-1102 (3MPX IP indoor mini dome, PAL)
TVD-3102 (3MPX IP indoor mini dome, NTSC)
TVW-1101 (1.3MPX IP wedge dome, PAL)
TVW-3101 (1.3MPX IP wedge dome, NTSC)
TVW-1102 (3MPX IP wedge dome, PAL)
TVW-3102 (3MPX IP wedge dome, NTSC)

Installation Guide 7
Installation
This section provides information on how to install the
cameras.
Installation environment
When installing your product, consider these factors:
• Electrical: Install electrical wiring carefully. It should be
done by qualified service personnel. Always use a proper
PoE switch or a 12 VDC UL listed Class 2 or CE certified
power supply to power the camera. Do not overload the
power cord or adapter.
• Ventilation: Ensure that the location planned for the
installation of the camera is well ventilated.
• Temperature: Do not operate the camera beyond the
specified temperature, humidity or power source ratings.
The operating temperature of the camera is between -30
to +60°C (-22 to 140°F). Humidity is below 90%.
• Moisture: Do not expose the camera to rain or moisture,
or try to operate it in wet areas. Turn the power off
immediately if the camera is wet and ask a qualified
service person for servicing. Moisture can damage the
camera and also create the danger of electric shock.
• Servicing: Do not attempt to service this camera
yourself. Any attempt to dismantle or remove the covers
from this product will invalidate the warranty and may
also result in serious injury. Refer all servicing to qualified
service personnel.
• Cleaning: Do not touch the sensor modules with fingers.
If cleaning is necessary, use a clean cloth with some
ethanol and wipe the camera gently. If the camera will not

8 Installation Guide
be used for an extended period of time, put on the lens
cap to protect the sensors from dirt.
Package contents
Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use
the unit; contact the supplier immediately. If the unit is
returned, it must be shipped back in its original packaging.
Package contents:
Camera
Hex wrench (for dome and mini dome cameras only)
Installation manual
CD with Configuration manual and TruVision Device
Finder
CAUTION: Use direct plug-in UL listed power supplies
marked Class 2/CE certified or LPS (limited power source) of
the required output rating as listed on the unit.
Cable requirements
For proper operation, adhere to the following cable and power
requirements for the cameras. Category 5 cabling or better is
recommended. All network cabling must be installed according
to applicable codes and regulations.
Table 1 on page 9 lists the requirements for the cables that
connect to the camera.

Installation Guide 9
Table 1: Recommended power cable requirements
Bullet camera:
Mini dome:
Wedge camera:
12 VDC power jack or PoE (802.3af)
PoE (802.3af)
12 VDC power jack or PoE (802.3af)
VF dome camera: 12 VDC power jack or PoE (802.3af)
Camera description
Figure 1: IP bullet camera
Adjustable
bracket
Housing
Sun
shield
Grounding
screws
Reset button

10 Installation Guide
Figure 2: IP indoor mini dome camera
1. Base
2. Lens
3. Dome liner
4. Housing
5. Ethernet RJ45 and BNC
cable
6. Safety cable