Interlogix VD-IP-XP4DNP User manual

UVD-IP-XP4DNR(-P)
Camera User Manual
P/N 1072545A-EN • REV 1.0• ISS 18JUN12

Copyright © 2012 UTC Fire & Security. All rights reserved.
Trademarks and
patents
The Interlogix and UltraView names and logos are trademarks of
UTC Fire & Security.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626 5923, USA.
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
N4131
FCC compliance Class A: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.
ACMA compliance Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.
Canada This Class A digital apparatus complies with Canadian ICES-
003.
Cet appareil numérique de la class A conforme à la norme NMB-
003 du Canada.
European Union
directives
2004/108/EC (EMC directive): Hereby, UTC Fire & Security
declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive
2004/108/EC
2002/96/EC (WEEE directive): Products marked with this
symbol cannot be disposed of as unsorted municipal waste in
the European Union. For proper recycling, return this product to
your local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.
Contact information For contact information see our Web site: www.interlogix.com,
www.utcfssecurityproducts.eu

UVD-IP-XP4DNR(-P) Camera 1 - EN
Contents
Introduction 2
Product description 2
Features 2
User guidelines 2
Package contents 3
Plenum-compliant cabling 3
Installation 4
Viewing the camera via a digital (IP) connection 4
Software requirements 4
Connecting analog cables 6
Installing the camera 6
Angle adjustment 6
Zoom and focus adjustment 7
Connecting an analog monitor to set camera functions 8
Setting camera functions 8
White balance (WB) 8
Backlight compensation (BLC) 8
AI/AE exposure 8
Day/Night 9
Resolution 9
Flickerless control 9
Reset to factory default settings 10

EN - 2 UVD-IP-XP4DNR(-P) Camera
Introduction
This user manual provides basic information on setting up and using
the UVD-IP-XP4DNR(-P) Camera.
Product description
The UVD-IP-XP4DNR(-P) color video camera uses a digital signal
processor (DSP) to process video signals. The video camera includes
a microcontroller to provide high-quality images in changing lighting
environments with high-color reproduction and sharp pictures.
Features
Camera features include:
• H.264-SVC video compression with multistream capability.
• Pixim Seawolf technology
• Excellent performance in almost any lighting conditions
• Supports up to 4CIF resolution (540 HTVL analog).
• True day/night (removable IR cut filter) • Long life and high
reliability.
• DIP switch control of camera settings.
• Power over Ethernet (PoE) or Isolated switching power 12 VDC or
24 VAC.
• Vandal-resistant housing.
User guidelines
Use the following guidelines:
• Take appropriate safety precautions while completing
programming after installation.
• Always use a proper PoE switch or a 12 VDC or 24 VAC UL listed
Class 2 power supply to power the camera.
• Do not use the camera outside the temperature range
specifications: -30 to +50°C (-22 to +122°F)

UVD-IP-XP4DNR(-P) Camera 3 - EN
• If the light source where the camera is installed experiences rapid,
wide-variations in lighting, the camera may not operate as
intended.
WARNING: To reduce the risk of fire or electronic shock, do not
expose the camera to rain or moisture and do not remove the cover or
back.
Package contents
The UVD-IP-XP4DNR(-P) camera is shipped with the following items:
• The camera assembly
• 1 channel passive video transceiver
• AC power wiring harness
• Mounting screws, wall anchors, and hex key
• 150 mm DC jack to terminal adapter
Use the video output BNC and power jack for normal system
operation.
Figure 1: Camera assembly
Camera body
RJ45 Ethernet/PoE input
24 VAC / 12 VDC input
Video output (BNC)
Plenum-compliant cabling
The cable connections must be enclosed in a suitable metallic, or other
fire-resistant, low-smoke producing enclosure. The cabling used within

EN - 4 UVD-IP-XP4DNR(-P) Camera
the air space must be specifically marked for that purpose or enclosed
in a conduit.
Re-route the leads from the camera so they exit from the threaded
knockout on the side of the camera (see Figure 2 below.) Move the
plug from the side threaded knockout and place it on the knockout on
the base of the camera.
Figure 2: Plenum-compliant cabling
1. Plenum-rated conduit
2. Box for connections
3. Threaded knockouts
4. Ceiling
5. Camera body
6. Trim ring
Installation
To install the camera you will need to prepare the mounting surface,
make cable connections, and mount the camera.
Viewing the camera via a digital (IP) connection
You can connect the IP camera to a network and view the images
through a browser. To view via a Network Video Recorder or similar
digital video system, please refer to the documentation associated with
that system.
Software requirements
The UVD-IP camera requires:
Microsoft Internet Explorer

UVD-IP-XP4DNR(-P) Camera 5 - EN
A VLC player ActiveX plug-in is required to play video when
Internet Explorer is used to monitor the camera.
Figure 3: ActiveX plug-in option
To configure the camera:
1. Configure the UVD-IP camera with a default IP address: 10.1.2.11
2. Configure your host PC/laptop within the same subnet, ex:
10.1.2.10
3. Connect the URL http://10.1.2.11 with Internet Explorer.
4. Select the “Live” menu to view live video.
5. Enter the following username and password to access the
Maintenance menu.
Login: admin
Password: admin
The IP address of the camera can be changed from the
Maintenance menu.
6. Reboot the camera for the changes to take effect.

EN - 6 UVD-IP-XP4DNR(-P) Camera
Connecting analog cables
To connect the cables:
1. Connect a coaxial cable from the camera’s BNC connector to a
CCTV monitor or video recording device.
2. Connect a PoE switch, a 12 VDC or 24 VAC power supply to the
power input. Do not connect both the PoE connection and DC or
AC connection at the same time. The label on the camera gives
the following information:
Red cable. Power in.
Black cable. Power in.
White cable. Video out.
Black cable. Video ground.
Note: For 24 VAC or 12 VDC, Black or Red may be used for ground.
Installing the camera
To mount the camera, attach the camera to the mounting surface using
the appropriate fasteners.
Angle adjustment
To adjust the horizontal angle of the platform up to 180 degrees, turn
the platform (Figure 4 on page 7).
To adjust the horizontal angle of the rotor up to 350 degrees, turn the
rotor on the platform (Figure 4 on page 7).
To adjust the vertical angle of the platform up to 90 degrees, turn the
platform (Figure 4 on page 7).

UVD-IP-XP4DNR(-P) Camera 7 - EN
Figure 4: Camera adjustment
Platform horizontal adjustment
Platform vertical adjustment
Rotor horizontal adjustment
Zoom and focus adjustment
See Figure 5 below for the location of the zoom and focus ring
thumbscrews.
Figure 5: Zoom and focus adjustment
Zoom ring thumbscrew for
VA2 and focus ring for
VA9 lens
Focus ring thumbscrew for
VA2 and zooming ring for
VA9 lens
To adjust the camera zoom and focus:
1. Loosen the zoom ring thumbscrew.
2. Turn the zoom ring to set the desired zoom.
3. Tighten the zoom ring thumbscrew.
4. Loosen the focus ring thumbscrew.
5. Turn the focus ring to set the desired focus.
6. Tighten the focus ring thumbscrew.

EN - 8 UVD-IP-XP4DNR(-P) Camera
Connecting an analog monitor to set camera
functions
Connect a standard video monitor to the system to adjust the quality of
the video image using the DIP switches. The DIP switches can also be
adjusted when connected to the IP system.
To connect a video monitor:
1. Plug the monitor output cable to the video monitor output
connector (see Figure 1 on page 3).
2. Connect the BNC cable to the video monitor.
3. Adjust the DIP switches as desired.
Setting camera functions
You can set up six camera functions using the DIP switch bank on the
back of the camera. Figure 6 on page 9 shows the DIP switch layout.
White balance (WB)
White balance tells the camera what the color white looks like. Based
on this information, the camera will then display all colors correctly.
There are two methods to determine the WB:
• ATW (auto tracking white balance). The value used depends on
the lighting condition selected. It ensures reliable color
reproduction when lighting conditions change frequently.
• PTL (push-to-lock) white balance. WB is fixed at the moment the
DIP switch it set to ON.
Backlight compensation (BLC)
The backlight compensation function improves image quality when the
background illumination is high. It prevents the object in the center
from appearing too dark.
AI/AE exposure
Use this setting to select the method the camera uses to adjust to
different light levels. Use the Automatic Iris (AI) setting to fix the iris
value at F1.6. Use Auto Exposure (AE) setting to automatically set the
proper exposure according to the existing light conditions.

UVD-IP-XP4DNR(-P) Camera 9 - EN
Day/Night
This function controls whether the camera is in automatic day/night
mode or forced into night mode. When set to Auto Day/Night mode,
the camera produces high-quality color video during the day or when
light levels are high. It then switches to monochrome and removes the
infrared filter to improve IR sensitivity at night or when light levels are
low. Black and white mode forces the infrared filter to stay removed
therefore the camera stays in black and white mode.
Resolution
High resolution produces higher quality images but also increases the
file size of the video images.
Flickerless control
Flickerless control eliminates the flicker caused by the differences
between the frequencies (60 Hz) of the ionization of the gas in a
fluorescent light bulb with that of the vertical frequency (59.95 Hz) in
the camera. Although the difference is very small, it results in a slight
flicker at the top of the monitor scene or, in video over IP applications,
it would be interpreted as motion. Flickerless control helps reduce the
file size and transfer bit rates of compressed video images.
Figure 6: DIP switch layout (back of camera)
Table 1: DIP switch functions (Default in bold)
Switch Description
1. White Balance
ON: ATW mode; OFF: PTL mode

EN - 10 UVD-IP-XP4DNR(-P) Camera
Switch Description
2. Backlight Compensation
ON: BLC on; OFF: BLC off
3. Exposure AI/AE
ON: Auto Exposure (AE) mode; OFF: Auto Iris (AI) mode
4. Day/Night Setting
ON: Black and white mode; OFF: Auto Day/Night mode
5. High/Normal Resolution
ON: High resolution; OFF: Normal resolution
6. Flickerless Control
ON: Flickerless enabled; OFF: Normal
Reset to factory default settings
Use the reset button to reset the camera to factory defaults including
camera and network settings. With the camera powered up, press the
red reset button for 10 to 15 seconds. The red LED indicator light
flashes when the reset signal is accepted. See Figure 7 below for its
location.
Figure 7: Location of reset switch
Reset switch