Interlogix TVB-2203 User manual

TruVision IR
Bullet Camera
TVB
-2203 / TVB-4203
Installation Guide
P/N 1072925 • REV A • ISS 10FEB15

Installation Guide 1
Content
Product overview 1
Camera description 3
Installation 4
Programming 8
Setup menu 9
Specifications 10
Regulatory information 11
Product overview
This is the TruVision Bullet IR Camera Installation
Guide for models TVB-2203/TVB-4203. This guide
describes a standard installation.

2 Installation Guide
Package contents:
Camera with power
and video output
cables
4 M4 screws (4 x
25 mm) and 4 dry wall
anchors (Ø7.5 x
24.5 mm) for wall or
ceiling installation
Template Back box
Hex wrench
Installation Guide
Ceiling Mounting
11
11
2
22
2
1:Screw Hole for
Bracket
2:Screw Hole for
Mounting Base

Installation Guide 3
CD
•WEEE and Battery
Disposal
Camera description
1. Video cable
2. Power cable
3. Bracket
4. Camera
5. Sunshield
6. Lens
7. Back box

4 Installation Guide
Installation
To install the camera:
1. Using the template, place it level against the
mounting surface and mark the position of the
mounting holes.
2. Following all local codes, drill and prepare the
mounting holes.
3. Install the back box on the wall (optional).
Ceiling Mounting
11
11
2
22
2
1:Screw Hole for
Bracket
2:Screw Hole for
Mounting Base

Installation Guide 5
4. Route the cables to the cable hole and connect
the corresponding cables. Connect a 75 ohm
coaxial video cable to the video cable, and
connect a 12 VDC power supply to the power
cable.
5. Secure the camera to the ceiling or wall with the
supplied screws.

6 Installation Guide
6. Loosen the three camera screws and adjust the
camera according to the figure below to get an
optimum angle. Tighten the screws after
completing the adjustments.

Installation Guide 7
7. Adjust the zoom screw and focus screw until you
get the optimum surveillance angle.
Focus
Zoom
OSD button
8. Use the OSD button to configure the camera
parameters.
360°
90°
360°

8 Installation Guide
Programming
The camera can be programmed using OSD menus.
Once the camera hardware has been installed, you
configure the camera by using a TVS-C200 controller
(purchase separately).
The Setup menu provides access to the camera
configuration options. Please refer to the configuration
manual for further information on setting up the
camera. See page 9 for the setup menu.
Program the camera by attaching a standard video
monitor to the system.
To access the Setup menu:
1. Press the OSD control button (Enter) to access
the Main menu and its submenus.
2. Push the button up, down, left and right to move
between menu options.
3. Press the OSD control button to select an option.
4. When in a submenu, select Return to return to
the previous menu.
5. To exit the Main menu, move the cursor to Exit at
the bottom of the screen and press Enter. All
changes are saved.

Installation Guide 9
Setup menu

10 Installation Guide
Specifications
Power supply 12 VDC
Current Max. 420 mA
Power consumption Max. 5 W
Weight (net) 1350 g (1.97 lb.)
Dimensions 105 x 95 x 265.4 mm
(4.13 x 3.74 x 10.43 in.)

Installation Guide 11
Regulatory information
Copyright:
© 2015 United Technologies Corporation.
Interlogix is part of UTC Building & Industrial Systems, a unit of United
Technologies Corporation. All rights reserved.
Trademarks and patents:
Trade names used in this document may be trademarks or registered
trademarks of the manufacturers or vendors of the respective products.
Manufacturer:
Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification:
N4131
FCC compliance: Class A
Class A: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
ACMA compliance
Notice! This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to

12 Installation Guide
take adequate measures.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-0330
du Canada.
European Union directives:
12004/108/CE (EMC directive): Hereby, UTC Fire & Security declares that
this device is in compliance with the essential requirements and other
relevant provisions of Directive 2004/108/EC.
2012/19/EU (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted municipal
waste in the European Union. For proper recycling, return
this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
Contact information:
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu..