© 2017 United Technologies Corporation 2 / 2 466-5273 • REV C • ISS 14FEB17
7. You can automatically enroll the module into the system
by pressing the ENROLL button on the CPU. Consult the
UltraSync Modular Hub Reference guide for more
information.
Configuring the Relays
Relay Modes
The module features Single Pole Double Throw (SPDT) Form
C relays that can be configured in three different modes to
support different applications.
The relays are connected to the output terminals with Normally
Open and Normally Closed connections for your convenience.
Red LEDs light up when the respective relay is energized.
Connect the BUS jumper to provide bus voltage to all relays.
Do not connect AUXIN and NEG if you select this option.
Use the jumper next to the relay to select the mode suitable to
your requirements. Default is no jumper with relay in NC
position.
No Jumper
Dry contact closure provided to output terminal. Maximum
Load 30 VAC @ 1 A or 24 VDC @ 1 A.
Negative Switching: Jumper between C and NEG
System Common connection provided to output terminal @
typical 0 V. Do not exceed relay rating which is maximum load
30 VAC @ 0.5 A or 24 VDC @ 1 A.
Positive Switching: Jumper between AUXIN and C
The voltage provided to Common terminal of the relay will be
dependent upon the installation of the BUS jumper. Bus
Voltage provided to output terminal @ typical 12-13 VDC.
Maximum Load @ 12 V is total panel current of 1 A, this
includes all connected keypads and expansion modules. Do
not exceed relay rating.
Warning:
CHECK THE CURRENT REQUIREMENTS OF YOUR LOAD BEFORE CONNECTING.
THERE IS NO OVERCURRENT PROTECTION ON THE RELAYS. YOU MUST ENSURE
YOUR LOAD DOES NOT EXCEED THE RECEMMENDED LIMITS ABOVE. EXCEEDING
LIMITS CAN DAMAGE THE MODULE AND POSE AN ELECTRICAL HAZARD THAT COULD
RESULT IN A FIRE OR CAUSE SERIOUS ELECTRICAL SHOCK OR LOSS OF LIFE.
THE ULTRASYNC MODULAR HUB HAS OVERCURRENT PROTECTION ON THE BUS AND
MAY DISCONNECT THE BUS TO PROVIDE TEMPORARY PROTECTION. IF ENABLED,
YOUR PANEL WILL REPORT “OVERCURRENT FAULT” OR “EXPANDER
OVERCURRENT.” REPEATED OVERCURRENT CONDITIONS CAN RESULT IN
PERMANENET DAMAGE TO THE PANEL OR CONNECTED DEVICES.
Attention:
VERIFIER LES CONDITIONS ACTUELLES DE VOTRE CHARGE AVANT DE CONNECTER.
IL N'Y A PAS PROTECTION DE SURCHARGE SUR LES RELAIS. VOUS DEVEZ ASSURER
VOTRE CHARGE NE DEPASSE PAS LES LIMITES SUGGERER CI-DESSUS.
SUPERIEURE LIMITES PEUVENT ENDOMMAGER LE MODULE ET POSE UN RISQUE
ÉLECTRIQUE QUE POURRAIT CAUSER UN INCENDIE OU ENTRAÎNER UNE GRAVE
ÉLECTROCUTION OU DES PERTES DE VIE. LE HUB UltraSync MODULAIRE A DE LA
PROTECTION DE SURCHARGE SUR LE BUS DE COMMUNICATION POUR OFFRIR UNE
PROTECTION TEMPORAIRE. SI ELLE EST ACTIVÉE, VOTRE GROUPE PRÉSENTERA
SON RAPPORT "SURINTENSITÉ" OU "EXPANDER SURVOLTAGE." CONDITIONS DE
SURINTENSITÉ RÉPÉTÉ PEUT ENTRAÎNER UN ENDOMMAGEMENT PERMENANT AU
PANNEAU OU A DES APPAREILS CONNECTÉS.
Firmware
Remotely upgradeable using DLX 900.
Specifications
UltraSync Modular Hub systems
Relay Capacity UM-R4
UM-R10
Average
(no relays active)
25 mA
25 mA
Alarm/Maximum
(all relays active)
125 mA*
275 mA*
*If relays are inactive, calculation can be de-rated 25 mA per inactive
relay. If positive switching is utilized, additional current draw of
connected load must be included in power budget calculations.
Rated load 0.5 A at 30 VAC or
1 A at 24 VDC, max current 1 A,
min load 1 mA 5 VDC
Product Dimensions
(W × H × D) UM-R4
UM-R10
4.64” x 2.79” x 2.0”
118mm x 71mm x 51mm
4.64” x 2.79” x 2.5”
118mm x 71mm x 64mm
Non UL/ULC installations
14° to 131°F
(-10° to 55°C)
UL/ULC installations
32° to 120° F
(0° to 49° C)
−30° to 140°F
(−34° to 60°C)
Non UL/ULC installations
up to 95% noncondensing
UL/ULC installations
up to 85% noncondensing
Regulatory Information
Placed on the market by:
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-3B.
Cet appareil numérique de la classe B est conforme à la norme NMB-
003 du Canada.
Contact Information
For contact information, visit us online at www.interlogix.com.
For technical support, see www.interlogix.com/support
Copyright
Copyright © 2017 United Technologies Corporation. All rights
reserved.
Trademarks
Interlogix is a registered trademark of United Technologies
Corporation. Interlogix is part of UTC Climate, Controls &
Security, a unit of United Technologies Corporation.
