Interlogix TruVision TVB-2402 Instruction sheet

TruVision High Definition
TVI Camera Configuration
Manual
TVB
-2402/TVB-4402
TVD
-2402/TVD-4402
P/N 1072941-EN • REV A • ISS 10MAR15

Copyright
©
2015 United Technologies Corporation,
Interlogix is part of UTC Building & Industrial
Systems, a unit of
United Technologies Corporation. All rights reserved.
Trademarks and
patents
T
rade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products
.
Manufacturer
I
nterlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626
-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Contact information
For contact information
, see www.interlogix.com or
www.utcfssecurityproducts.eu
.
Customer suppor
t
www.interlogix.com/customer
-support

TruVision High Definition TVI Camera Configuration Manual 1
Content
Introduction 2
Programming 2
Menu 4
Automatic Exposure (AE) 4
White Balance (WB) 5
Day & Night 5
Video Setting 6
Function 6
Reset 8

2 TruVision High Definition TVI Camera Configuration Manual
Introduction
This is the configuration manual for following camera models:
TVB-2402 (720P TVI Bullet Camera, VF Lens, IR, PAL)
TVB-4402 (720P TVI Bullet Camera, VF Lens, IR, NTSC)
TVD-2402 (720P TVI Mini Dome, VF Lens, IR, PAL)
TVD-4402 (720P TVI Mini Dome, VF Lens, IR, NTSC)
Programming
Once the camera hardware has been installed, the camera can then be
configured using the built-in OSD button or an OSD controller (purchased
separately).
You can also configure the camera settings via a TVI DVR, select PTZ protocol
as TruVision Coax and click the menu button to call the menu.
Note:
Interlogix offers two different versions of the OSD Controller: the TVS-C100
controller and the TVS-C200 controller. Please choose the corresponding
controller by referring to product datasheets.
The cameras listed in the “Introduction” section support TruVision Coax OSD
control protocol and require the TVS-C200 for OSD control.
The TVS-C200 is used to program the camera’s 960H CVBS output, not for the
TVI video output. Programming the camera’s TVI output can be done via a TVI
DVR.
The TVS-C200 has four buttons for the camera functions selection and control.
Table 1 below lists the OSD control button functions and describes their use.

TruVision High Definition TVI Camera Configuration Manual 3
Figure 1: TVS-C200 coax controller
1. Indicator light
2. Arrow keys
3. OK button
The Setup menu provides access to the camera configuration options.
Before using the controller, please check to ensure that the controller has power.
Two AAA batteries are required for the controller to work properly.
1. Connect a video monitor to one of the BNC connectors of the controller.
2. Connect the camera’s 960H CVBS output to the other BNC connector
3. Press the OK button for few seconds to display the Setup menu. See Table 1
for instructions on how to move the cursor.
Table 1 Using the OSD control button
Button
direction Description
Up
Moves the cursor upward to select an item
Left
Moves the cursor left to select or adjust the parameters of the selected
item.
Right
Moves the cursor to the right to select or adjust the parameters of the
selected item.
Down
Moves the cursor downward to select an item.
OK
Press the red button for few seconds to display the Setup menu. If the
selected item has its own menu, press the button to enter a submenu.

4 TruVision High Definition TVI Camera Configuration Manual
Menu
Automatic Exposure (AE)
Automatic exposure (AE) allows you to automatically set the proper exposure
according to the existing light conditions.
Move the cursor to MAIN MENU > AE, to adjust the image brightness using the
BRIGHTNESS, AE MODE, AGC, and SENS-UP options.
BRIGHTNESS: Brightness refers to the brightness of the image. You can set the
brightness value from 1 to 10 to darken or brighten the image. The higher the
value, the brighter the image.
AE MODE: You can set AE mode as GLOBLE AE, and D-WDR:

GLOBAL AE: This refers to the normal exposure mode which is for adjusting
the situations including unusual lighting distribution, variations, non-standard
processing, or other conditions of under exposure to get an optimum image.

DWDR: The digital wide dynamic range (D-WDR) function helps the camera
provide clear images even under back light circumstances. When there are

TruVision High Definition TVI Camera Configuration Manual 5
both very bright and very dark areas simultaneously in the field of view, D-
WDR balances the brightness level of the whole image and provide clear
images with details.
AGC: This is a form of amplification where the camera will automatically boost
the image received in much lower light conditions than standard in order to
optimize the clarity of image in poor light scene. The AGC level can be set to
HIGH, MIDDLE, and LOW. Select OFF to disable the AGC.
Note: The noise will be amplified if the AGC is on.
SENSE UP: This increases the exposure on a signal frame, which makes a
camera more sensitive to light so it can produce images even in low lux
conditions. You can set the SENSE UP value from 0 to 16 according to the
different light conditions. The higher value is, the more frames integrated in a unit
of time.
White Balance (WB)
White balance is the white rendition function of the camera to adjust the color
temperature according to the environment. It can remove the unrealistic color
casts in the image. You can set the WB mode as AUTO or MANUAL.
AUTO: The white balance is adjusted automatically according to the color
temperature of the scene illumination.
MANUAL: You can set the R GAIN/B GAIN value from 1 to 10 to adjust the
shades of red/blue color of the image.
Day & Night
Move the cursor to MAIN MENU > DAY & NIGHT, and select COLOR, B/W, or
SMART as the DAY & NIGHT mode.
COLOR: The image is colored in day mode all the time.
B/W: The image is black and white all the time, and the IR LED turns on in low-
light conditions.
SMART: Turn on/off the INFRARED_LAMP and set the Smart IR level from 1to
16.

6 TruVision High Definition TVI Camera Configuration Manual
Video Setting
Move the cursor to the MAIN MENU >VIDEO SETTING.
CONTRAST: This feature enhances the difference in color and light between
parts of an image. Set the CONTRAST value from 1 to 10.
SHARPNESS: Sharpness determines the amount of detail an imaging system
can reproduce. You can also adjust the EDGE/DETAIL sharpness value. Set the
edge and detail sharpness value from 1 to 10. A higher value of sharpness
results in a clearer and sharper image.
COLOR GAIN: Adjust this feature to change the saturation of the color. Set the
color gain from 1 to 10.
3D NR: Compared to traditional general 2D NR technology, 3D NR processes
the noise reduction between two frames instead of in one frame. It can decrease
the noise effect, especially when capturing moving images in low light conditions
and delivering more accurate and sharp image quality. Set the 3D NR level as
High, Middle, and Low. Select OFF to disable the 3D NR.
MIRROR: Set the mirror mode as OFF, H, V, or HV.

OFF: The mirror function is disabled.

H: The image flips 180 degree horizontally.

V: The image flips 180 degree vertically.

HV: The image flips 180 degrees both horizontally and vertically.
Function
Move the cursor to the MAIN MENU > FUNCTION. You can set DETECTION,
MASKING, ZOOM IN and LANGUAGE of the camera in this menu.

TruVision High Definition TVI Camera Configuration Manual 7
DETECTION: In the user-defined detection surveillance area, the moving object
can be detected and the alarm will be triggered. Set the motion sensitivity as
WEAK, LOW, MIDDLE or HIGH. Select an AREA to enter the motion detection
AREA menu.
MASKING: Masking allows you to cover certain areas that you do not want to be
viewed or recorded. Up to eight masking areas are configurable. Select a
masking back ground color. Select an AREA to enter the masking AREA menu.
ZOOM IN: The ZOOM IN value can be adjusted from 50 to 100.
LANGUAGE: Select either Chinese or English.
AREA: There are four surveillance areas set for motion detection. Select one and
set the status as OFF/ON. Select a color for area border. Move the joystick
up/down and right/left to set the horizon/vertical size and position.

8 TruVision High Definition TVI Camera Configuration Manual
AREA: There can be eight masking areas set for motion detection. Set the status
as OFF/ON. Move the joystick up/down and right/left to set the horizon/vertical
size and position.
Reset
Move the cursor to the MAIN MENU >RESET. This resets all the settings to
default.
SAVE & EXIT: Move the cursor to SAVE & RESET and press OK to save the
settings and exit the menu.