Interlogix TruVision 4 Series User manual

TruVision
Series 4 IP
Camera Installation
Guide
P/N 1073195-EN • REV E • ISS 15MAY19

Copyright
© 2019 United Technologies Corporation,
Interlogix is part of UTC Climate, Controls &
Security, a unit of United Technologies
Corporation. All rights reserved.
Trademarks and
patents
Trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Manufacturer
Interlogix
2955 Red Hill Avenue, Costa Mesa, CA
92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
FCC compliance
Class A: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation of
this equipment in a residential area is likely to
cause harmful interference in which case the user
will be required to correct the interference at his
own expense.
FCC conditions
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful

interference.
(2) This Device must accept any interference
received, including interference that may cause
undesired operation.
ACMA compliance
Notice! This is a Class A product. In a domestic
environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
Canada
This Class A digital apparatus complies with CAN
ICES-003 (A)/NMB-3 (A).
Cet appareil numérique de la classe A est
conforme à la norme CAN ICES-003 (A)/NMB-3
(A).
cUL
Safety Instructions:
Improper use or replacement of the battery may
result in explosion hazard. Replace with the same
or equivalent type only. Dispose of used batteries
in conformance with the local codes.
Instructions de sécurité:
L’utilisation ou le remplacement inadéquats de la
pile peuvent entraîner un risque d’explosion.
Remplacez-la par le même type ou l’équivalent du
même type seulement. Jetez les piles usagées
conformément aux directives fournies par le
fabricant de la pile.
European Union
directives
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized
European standards listed under the EMC
Directive 2014/30/EU, the RoHS Directive
2011/65/EU.

2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see:
www.recyclethis.info.
2013/56/EU &2006/66/EC (battery directive): This
product contains a battery that cannot be disposed
of as unsorted municipal waste in the European
Union. See the product documentation for specific
battery information. The battery is marked with this
symbol, which may include lettering to indicate
cadmium (Cd), lead (Pb), or mercury (Hg). For
proper recycling, return the battery to your supplier
or to a designated collection point. For more
information see: www.recyclethis.info.
Product warnings
and disclaimers
THESE PRODUCTS ARE INTENDED FOR SALE
TO, AND INSTALLATION BY, AN EXPERIENCED
SECURITY PROFESSIONAL. UTC FIRE &
SECURITY CANNOT PROVIDE ANY
ASSURANCE THAT ANY PERSON OR ENTITY
BUYING ITS PRODUCTS, INCLUDING ANY
“AUTHORIZED DEALER”, IS PROPERLY
TRAINED OR EXPERIENCED TO CORRECTLY
INSTALL SECURITY RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
www.firesecurityproducts.com/policy/product-
warning/ or scan the following code:

Contact information
and manuals
For contact information go to: www.interlogix.com
or www.firesecurityproducts.com
To get translations for this and other product
manuals go to: www.firesecurityproducts.com

Installation Guide 1
Content
Introduction 2
Product overview 2
Installation 3
Installation environment 3
Package contents 4
Cable requirements 10
Camera description 12
Setting up the camera 16
IR illuminators 17
Accessing the SD card 18
Mounting the bullet camera 18
Mounting the VF mini dome camera 19
Mounting the outdoor dome camera 25
Using the camera with a TruVision recorder or another
system 30
Using the camera with TruVision Navigator 30
Specifications 30
TruVision IP box cameras 30
TruVision IP VF bullet dome 31
TruVision IP VF mini cameras 31
TruVision IP VF outdoor dome cameras 32
Pin definitions 33

2 Installation Guide
Introduction
Product overview
This is the installation guide for TruVision Series 4 IP camera
models:
TVC-5401 (2MPX IP box camera)
TVC-5402 (3MPX IP box camera)
TVC-5403 (5MPX IP box camera)
TVB-5401 (2MPX IP bullet camera, 2.8 to 12 mm)
TVB-5402 (2MPX IP bullet camera, 8 to 32 mm)
TVB-5403 (3MPX IP bullet camera, 2.8 to 12 mm)
TVB-5404 (3MPX IP bullet camera, 8 to 32 mm)
TVB-5405 (5MPX IP bullet camera, 2.8 to 12 mm)
TVD-5401 (2MPX IP VF mini dome, 2.8 to 12 mm)
TVD-5402 (3MPX IP VF mini dome, 2.8 to 12 mm)
TVD-5403 (5MPX IP VF mini dome, 2.8 to 12 mm)
TVD-5404 (2MPX IP outdoor dome, 2.8 to 12 mm)
TVD-5405 (2MPX IP outdoor dome, 8 to 32 mm)
TVD-5406 (3MPX IP outdoor dome, 2.8 to 12 mm)
TVD-5407 (3MPX IP outdoor dome, 8 to 32 mm)
TVD-5408 (5MPX IP outdoor dome, 2.8 to 12 mm)

Installation Guide 3
Installation
This section provides information on how to install the
cameras.
Installation environment
When installing your product, consider these factors:
•Electrical: Install electrical wiring carefully. It should be
done by qualified service personnel. Always use a proper
PoE switch or a 12 VDC UL listed Class 2 or CE certified
power supply to power the camera. Do not overload the
power cord or adapter.
•Ventilation: Ensure that the location planned for the
installation of the camera is well ventilated.
•Temperature: Do not operate the camera beyond the
specified temperature, humidity or power source ratings.
The operating temperature of the camera without heater
is between -30 to +60°C (-22 to 140°F). Humidity is below
90%. For the outdoor cameras that feature built-in
heaters, the operating temperature range is -40 to 60°C
(-40 to140°F)
•Moisture: Do not expose the camera to rain or moisture
or try to operate it in wet areas. Turn the power off
immediately if the camera is wet and ask a qualified
service person for servicing. Moisture can damage the
camera and also create the danger of electric shock.
•Servicing: Do not attempt to service this camera
yourself. Any attempt to dismantle or remove the covers
from this product will invalidate the warranty and may
also result in serious injury. Refer all servicing to qualified
service personnel.

4 Installation Guide
•Cleaning: Do not touch the sensor modules with fingers.
If cleaning is necessary, use a clean cloth with some
ethanol and wipe the camera gently. If the camera will not
be used for an extended period of time, put on the lens
cap to protect the sensors from dirt.
Package contents
Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use
the unit; contact the supplier immediately. If the unit is
returned, it must be shipped back in its original packaging.
IP box camera
•Camera •C-CS adaptor
•CD with Configuration
manual and TruVision
Device Manager
•WEEE and Battery
Disposal sheets