Intermec 5020 User manual

nugget
39
243X and 502X Holster Instructions
You can use the holster (Part No. 072366) to carry your Trakker Antares®243X
terminal or 502X Hand-Held Data Collection PCat your side.
The holster ships ready to be worn
on either side. You can also use the
three mounting loops to configure
the holster to accommodate a 243X
or 502X with a handle.
These instructions describe
how to configure the holster to
accommodate a 243X or 502X with
a handle and how to put on the
holster. Before using the holster,
please read these instructions
thoroughly and retain them for
future reference.
Waist belt
buckle
Leg strap
243X5020I001.eps
To configure the holster for a 243X or 502X with a handle
1. Remove the Phillips screw from
the top of the mounting bar.
2. Slide the holster cup up and off of
the mounting bar.
3. Insert the mounting bar into a
different mounting loop on the
holster cup.
Use the loop to the right of the
original loop to wear the holster
on the right, and use the loop to
the left of the original loop to wear
the holster on the left.
4. Replace the screw in the top of the
mounting bar and tighten.
5. Slide the mounting assembly to
the appropriate side of the waist
belt.
To learn how to put on the holster,
continue with the next procedure.
1
2Holster
cup
Mounting
loop
(3 places)
Mounting
bar
Mounting
bar
Phillips
screw
243X5020I002.eps
243X and 502X Holster Instructions
You can use the holster (Part No. 072366) to carry your Trakker Antares®243X
terminal or 502X Hand-Held Data Collection PCat your side.
The holster ships ready to be worn
on either side. You can also use the
three mounting loops to configure
the holster to accommodate a 243X
or 502X with a handle.
These instructions describe
how to configure the holster to
accommodate a 243X or 502X with
a handle and how to put on the
holster. Before using the holster,
please read these instructions
thoroughly and retain them for
future reference.
Waist belt
buckle
Leg strap
243X5020I001.eps
To configure the holster for a 243X or 502X with a handle
1. Remove the Phillips screw from
the top of the mounting bar.
2. Slide the holster cup up and off of
the mounting bar.
3. Insert the mounting bar into a
different mounting loop on the
holster cup.
Use the loop to the right of the
original loop to wear the holster
on the right, and use the loop to
the left of the original loop to wear
the holster on the left.
4. Replace the screw in the top of the
mounting bar and tighten.
5. Slide the mounting assembly to
the appropriate side of the waist
belt.
To learn how to put on the holster,
continue with the next procedure.
1
2Holster
cup
Mounting
loop
(3 places)
Mounting
bar
Mounting
bar
Phillips
screw
243X5020I002.eps

nugget
39
To put on the holster
1. With the holster on the outside
of your thigh, buckle the waist
belt around your waist.
2. Adjust the waist belt so it is
snug and comfortable for you.
3. Buckle the leg strap around your
thigh.
4. Adjust the leg strap so it is snug
and comfortable for you.
Waist belt
buckle
Leg strap
243X5020I001.eps
6001 36th Avenue West
Everett, WA 98203
U.S.A.
www.intermec.com
© 2002 Intermec Technologies Corp.
All Rights Reserved
243X and 502X Holster Instructions
*068981-002*
*068981-002*
To put on the holster
1. With the holster on the outside
of your thigh, buckle the waist
belt around your waist.
2. Adjust the waist belt so it is
snug and comfortable for you.
3. Buckle the leg strap around your
thigh.
4. Adjust the leg strap so it is snug
and comfortable for you.
Waist belt
buckle
Leg strap
243X5020I001.eps
6001 36th Avenue West
Everett, WA 98203
U.S.A.
www.intermec.com
© 2002 Intermec Technologies Corp.
All Rights Reserved
243X and 502X Holster Instructions
*068981-002*
*068981-002*