INTERNATIONAL CARBONIC CONCEPT JUNIOR Manual

CONCEPT JUNI OR
I NSTALLATON AND SERVI CE
MANUAL
I
C
I
I NTERNATI ONAL CARBONI C I NC.
16630 Koala Rd.
Adelanto, California 92301
800 854-1177
12/ 04
Chilled
Fruit Juices
C- JR
Chilled
Fruit Juices
C- JR- PP
CONCEPT JUNIOR PERISTALTIC PUMP UNIT
CONCEPT JUNI OR UNI T

IMPORTANT: This manual is a guide for installing,
operating, servicing and maintaining this equipment. Refer
to Table of Contents for page location of detailed
information to answer questions that arise during
installation, operating, service and maintenance, or
installation of this equipment.

TABLE OF CONTENTS
PAGE
PREFACE .............................................................................................. 1
CHAPTER 1
GENERAL DESCRIPTION ..................................................................... 2
SYSTEM DESCRIPTION........................................................................ 2
DESIGN DATA ...................................................................................... 3
THEORY OF OPERATION ..................................................................... 3
EXPLODED VIEW C-JR-PP.................................................................... 5
EXPLODED VIEW DESCRIPTION C-JR-PP ........................................... 6
EXPLODED VIEW C-JR ......................................................................... 8
EXPLODED VIEW DESCRIPTION C-JR ................................................. 9
PFC-II-PP EXPLODED VIEW ................................................................. 11
PFC-II EXPLODED VIEW ....................................................................... 12
PFC-II EXPLODED VIEW DESCRIPTION............................................... 13
ELECTRIC SCHEMATIC PPM ............................................................... 14
ELECTRIC SCHEMATIC ....................................................................... 15
S-1737 ASSEMBLY EXPLODED VIEW .................................................. 16
S-1743 REPLACEMENT ASSEMBLY EXPLODED VIEW........................ 17
CHAPTER II
UNPACKING AND INSPECTION........................................................... 18
SELECTING LOCATION........................................................................ 18
LOCATION RECOMMENDATIONS........................................................ 18
SAMPLE OF POSSIBLE INSTALLATION .............................................. 19
INSTALL WATER FILTER ASSY. .......................................................... 19
INSTALL WATER PRESSURE REGULATOR ......................................... 20
INSTALL DRAIN LINE........................................................................... 20
INSTALL B.I.B. ..................................................................................... 20
CONNECTING WATER INLET............................................................... 21
ELECTRICAL REQUIREMENTS ............................................................ 21
CHAPTER III
PREPARING SYSTEM FOR OPERATION .............................................. 22
PREPARING AND STARTING REFRIGERATION UNIT......................... 22
PURGE DISPENSING VALVE................................................................ 22
ADJUST WATER FLOW RATE .............................................................. 22
ADJUST WATER TO SYRUP RATIO ..................................................... 22
CHAPTER IV
OPERATORS INSTRUCTIONS.............................................................. 23
DAILY PRE-OPERATION CHECK.......................................................... 23
COOLING UNIT MAINTENANCE .......................................................... 23
CHECKING WATER BATH .................................................................... 23
CHANGING WATER BATH.................................................................... 23
CLEANING NOZZLES ........................................................................... 23
CHAPTER V
SERVICE AND MAINTENANCE ............................................................ 24
PERIODIC INSPECTION AND CLEANING ............................................ 24
PERIODIC CLEANING........................................................................... 24
CLEANING CONDENSER COIL............................................................. 24
CHANGING WATER BATH.................................................................... 25
CHANGING PERISTALTIC PUMP TUBING........................................... 26
CLEANING AND SANITIZING............................................................... 27
BRIX INSTRUCTIONS PFC-II-PP .......................................................... 29
BRIX INSTRUCTIONS PFC-II................................................................ 30
BRIX PROCEDURES ............................................................................. 31
TROUBLE SHOOTING .......................................................................... 32
NOTES .................................................................................................. 33

PREFACE
INTERNATIONAL CARBONIC INC. has enjoyed
over 53 years of manufacturing excellence in the
field of carbonation and in the beverage related
industry. We have been located in the Southern
California area since 1952 and have a long and
proud history with quality as our standard and
innovation as our goal. Originally started just
after World War II in Canfield Ohio as Carbonic
Dispensers we enjoyed patents on the first
Sodajet type carbonator. This method of
carbonation instantaneously carbonated the
water to 100% saturation. We developed the
first patented dispensing valve to dispense bulk
beverage with carbonation equal to or in excess
of bottled beverages. A valve with three flavors
and soda was another first. We were the first to
incorporate the total post-mix package, i.e.,
carbonation, refrigeration & the ability to
dispense from one self contained unit. We have
pioneered many such firsts and will continue to
develop advance systems for the future, such as
electronic interrogatable portion controls to
electronic liquid level controls.
We hope you enjoy this product that has been
produced to give many years of trouble free
service. We thank you for your purchase and
hope we may serve you in the future.
1

C-JR-PP or C-JR CHAPTER I
GENERAL DESCRIPTION
This chapter gives the description, theory of operation, and design data for the
CONCEPT JR JUICE PERISTALTIC PUMP unit, (C-JR-PP) or CONCEPT JR less
peristaltic pumps, (C-JR), and related components.
SYSTEM DESCRIPTION
The C-JR-PP is a complete self-contained Juice unit which when combined with B.I.B
containers, will produce a variety of cooled non-carbonated beverages. The C-JR-PP
or C-JR consists of a water bath, refrigeration system and valves. The C-JR-PP will
be equipped with a modular peristaltic pump compartment. The cabinet and
peristaltic pump module are housed in a rugged stainless steel housing. The C-JR-PP
has been designed to eliminate the use of bag in the box pumps and associated
components. The C-JR-PP will dispense product with B.I.B.’s at a distance of 100
feet horizontally or 17 feet vertically. THESE DISTANCES ARE ONLY POSSIBLE IF
THE SUPPLY LINE HAS COMPLETE INTEGRITY. IF EVEN THE SMALLEST VACUUM
LEAK IS ALLOWED THESE DISTANCES ARE NOT POSSIBLE. The C-JR-PP or C-JR can
brix from one to one up to twenty to one by using a state of the art
controller/potentiometer adjustment. The C-JR will require external BIB Pumps.
For proper function the C-JR-PP or C-JR must have a water supply, and electrical
supply and drainage. The C-JR-PP or C-JR is designed with a unique lift off drain pan
that can be emptied at any convenient drain outlet.
WARNING: Before shipping or relocating a C-JR-PP or C-JR into a
freezing ambient environment empty plain water. Syrup systems
should be flushed, ice bank melted, and water drained from
water bath. A freezing ambient environment will cause existing
water in unit to freeze possibly resulting in damage to water coil,
peristaltic pumps, water bath, valve(s), etc.
Water Filter Recommended (Optional) See Manufacturer Specifications for Operating
Conditions
2

DESIGN DATA
C-JR-PP or C-JR
Overall Cabinet/P.P. Base dimensions:
C-JR-PP C-JR
Height..................................................... 29 1/8 ..................... 20 7/8
Width ...................................................... 12 ........................... 12
Depth...................................................... 24 ........................... 24
Weights:
Shipping pounds..................................... 128 ......................... 108
Dry weight pounds ................................. 106 ........................ 86
Operational Weight pounds ................... 146 ......................... 126
Capacities:
Unit water bath gallons 5
Refrigerant requirement (R-134a) ounces 6.3
Grams 180
Ambient operating temperature 40 F to 100 F
Electrical Requirements:
The cooling unit requires a 115 VAC, single phase, 60 Hertz power circuit.
Circuit Ampacity Amps ............................... C-JR-PP 3.8 ............ C-JR 2.8
Condensing Unit Amps................................................................ 2.1
Agitator Amps ............................................................................. .8
Peristaltic Pump Assembly @ 4 valves Amp . ............................. 1
Illumination (Optional) ................................................................ .5
REFRIGERATION 1/5 H.P. capillary air-cooled.
THEORY OF OPERATION
The C-JR-PP or C-JR was designed to manufacture and dispense non-
carbonated beverages much like your local bottling plant that cans or bottles
your favorite non-carbonated drink.
The water bath must be filled with approximately 5 gallons of water. After all
connections are made and activation of the refrigeration a certain amount of
this water will be transformed into ice, approximately 17 pounds. This water
reserve and ice bank will act as a reservoir for refrigeration. This reserve is
utilized during peak periods when the BTU output of the compressor is not
sufficient to meet the demand of the draw.
3

The incoming water is routed through a water coil that is submerged in the
above mentioned water bath. The temperature of the incoming water is at
ambient temperature as it enters the submerged water coil. As the incoming
water passes through the water coil the heat is removed from the water in the
water coil and chilled to a temperature acceptable for a quality drink,
normally a temperature of 33 to 34 degrees is reached. The water is now
directed to a valve where the water and syrup are mixed in proper proportions
to dispense a quality drink. Depending on the ratio of water versus syrup the
temperature will rise and be dispensed at approximately 40 degrees
Fahrenheit.
With the incorporation of the peristaltic pump the necessity for an air or CO2
supply is no longer necessary, this includes the low and high-pressure
regulators normally needed for a standard juice unit. The peristaltic pumps
will pull the syrup concentrate from the B.I.B., (bag in the box), and then push
the syrup through syrup cooling coils, (optional), and then to the valve where
the syrup concentrate and water are mixed in a proper ratio to dispense a
quality drink. The syrup enters the C-JR-PP through a unique 1/4” X 3/8 S-162
bulkhead fitting at the rear of the unit.
The water source should be regulated, this is normally performed by the use of
an in line water regulator. If the water is not regulated and the water
pressure can vary. This variance of water pressure can affect our dispensed
product.
4

INTERNATIONAL CARBONIC I NC.
ADELANTO, CALI FORNI A
TI TLE
DATE
DRN. BY
CHK. BY
APPR. BY
CONCEPT
JUNI OR PP
12/13/ 04
GLW
I
C
I
Chilled
Fruit Juices
16
Chilled
Fruit Juices
12
11
10
7
2
3
8
5
14
15
9
9
4
13
6
9
1
17
18
9
31 21
20
21
32 37
41
39
42
44
9
28
27
39 45 46
43
26
24
33
34
48
47
19
50 51
53
49 29
52
30
54
55
61
60
58
62
36
40
56
35 63
57
64
66
65
65 67
38
22
25
23
9
59
40
35
GLW
GLW
5

CONCEPT JR PP
SYM
QTY
PART NO.
DESCRIPTION
1
1
S1201
COVER ONLY
2
1
S0955
STARTER
3
1
S0958
STARTER HOLDER
4
4
G0010
END BELL
5
1
S1228
LAMP HOLDER BOX W/COVER
6
2
A0009
SCREW, 8 X 3/8" PHIL P.H.
7
1
E0665
STRAIN RELIEF, (ZIP CORD)
8
2
S0973
LAMP HOLDER
9
7
A0020
SCREW, 8-32 X 3/8 T.H., S.S.
10
1
S1227
LAMP MOUNTING PLATE
11
1
S0956
LAMP
12
1
S0985-J-M
PANEL, JUICE, MODIFIED
13
2
A0060
SCREW, 6-32 X 1/4, FLAT HEAD
14
1
S0952
BALLAST
15
1
S1229
LAMP HOLDER BOX COVER ONLY
16
1
S1203
REFRIGERATION DECK, COMPLETE,INCLUDES #'S 17 - 30
17
2
A0046
5-16 X- 18 X 3/4 FLANGE WHIZ LOCK SCREW
18
1
S0192Y
REFRIGERATION DRIER, R-134A ONLY
19
1
AEA1360YXA
COMPRESSOR ONLY, 1/5 H.P.
20
1
AEA1360YXAXA
CONDENSING UNIT, 1/5 H.P.
21
2
S1470
HANDLE
22
1
S0513A
ICE BANK CONTROL
23
2
A0052
SCREW, 6-32 X 3/8 PHIL PH
24
1
H0019
1 1/2" HOLE PLUG
25
1
S1304-U
ICE BANK CONTROL BRACKET
26
1
- - - - - -
12 - .042 CAP TUBE
27
4
A0024
10-24 X 3/8 TH, SCREW
28
1
S1333
EVAPORATOR ASSY.
29
1
S0509
ACCUMULATOR
30
5
S1204
EVAPORATOR RETAINER PINS
31
1
S1206
WATER COIL RETAINER BRACKET
32
1
S0835
AGITATOR PUMP
33
1
S1306-LG
AGITATOR PUMP BRACKET
34
2
F0004
SCREW, #8 X 1/2 PH HD SELF TAPPING
6

CONCEPT JR PP continued
SYM
QTY
PART NO.
DESCRIPTION
35
8
A0014
SCREW, #10 X 1/2" PHILLIPS TH SS
36
1
S1700
TRANSFORMER, 100 VA, 120 VOLT/24 VOLT
37
1
S1244
SNAP IN RECEPTACLE
38
2
E0674
BUSHING, SNAP
39
4
S0046
BUSHING
40
8
S1325
SQUARE GROMMET NUT
41
4
S1335
TERMINAL BOARD SPACER
42
1
S1309
TERMINAL BOARD
43
1
S0766
UNIT ON/OFF SWITCH
44
1
S1210
CONTROL BOX COVER
45
1
A0017
GROUND SCREW, #8 X 1/2 INDENTED HEX SLOT
46
1
S1209
CONTROL BOX
47
1
S1207-4
VALVE HOUSING
48
1
S0768
SWITCH LOCK
49
2
S0768-K
KEY ONLY, SWITCH LOCK
50
4
S1313
VALVE SWITCH, PUSH HERE
51
1
S1208-4
VALVE MOUNTING PLATE
52
1
S1334
WATER COIL
53
4
PFC-II-PP
VALVE, PERISTALTIC PUMP
54
1
S1211
STANDPIPE, 8 3/16"
55
1
S1205
WRAPPER & BUCKET ASSY W/INSULATION
56
8
S1698
PLASTIC CLAMP
57
4
S1737
PERISTALTIC PUMP ASSEMBLY, COMPLETE
58
4
A0045
5/16 - 18 FLANGE WIZ LOCK SCREW 1/2"
59
1
E0664
STRAIN RELIEF
60
5
S0162
BULK HD FITTING SS 1/4 H X 3/8 H W/HEX BODY
61
5
S0286A
NUT, SS LOCKING HEX HD 1/2-20
62
1
S1212
PP BASE ASSY
63
1
S1213
PP BASE ASSY COVER
64
1
S1215
CUP REST
65
1 SET
S0743
DRAIN PAN HARDWARE, SET
66
1
S1214
DRAIN PAN W/CUP REST
67
1
E0141-12
ELECTRICAL POWER CORD
7

INTERNATIONAL CARBONIC INC.
ADELANTO, CALI FORNI A
TI TLE
DATE
DRN. BY
CHK. BY
APPR. BY
CONCEPT
JUNI OR
12/13/ 04
GLW
I
C
I
Chilled
Fruit Juices
16
Chilled
Fruit Juices
12
11
10
7
2
3
8
5
14
15
9
9
4
13
6
9
1
17
18
9
31 21
20
21
32 35
44
39
38
40
41
9
28
27
38
43
37
42
26
24
33
34
47
46
19
49 50
52
48 29
51
30
53
54
55
56
57
57
58
36
22
25
23
9
45
59
8

CONCEPT JR
SYM
QTY
PART NO.
DESCRIPTION
1 1 S1201 COVER ONLY
2 1 S0955 STARTER
3 1 S0958 STARTER HOLDER
4 4 G0010 END BELL
5 1 S1228 LAMP HOLDER BOX W/COVER
6 2 A0009 SCREW, 8 X 3/8" PHIL P.H.
7 1 E0665 STRAIN RELIEF, (ZIP CORD)
8 2 S0973 LAMP HOLDER
9 7 A0020 SCREW, 8-32 X 3/8 T.H., S.S.
10 1 S1227 LAMP MOUNTING PLATE
11 1 S0956 LAMP
12 1 S0985-J-M PANEL, JUICE, MODIFIED
13 2 A0060 SCREW, 6-32 X 1/4, FLAT HEAD
14 1 S0952 BALLAST
15 1 S1229 LAMP HOLDER BOX COVER ONLY
16 1 S1203 REFRIGERATION DECK, COMPLETE,INCLUDES #'S 17 - 30
17 2 A0046 5-16 X- 18 X 3/4 FLANGE WHIZ LOCK SCREW
18 1 S0192Y REFRIGERATION DRIER, R-134A ONLY
19 1 AEA1360YXA COMPRESSOR ONLY, 1/5 H.P.
20 1 AEA1360YXAXA CONDENSING UNIT, 1/5 H.P.
21 2 S1470 HANDLE
22 1 S0513-A ICE BANK CONTROL
23 2 A0052 SCREW, 6-32 X 3/8 PHIL PH
24 1 H0019 1 1/2" HOLE PLUG
25 1 S1304-U ICE BANK CONTROL BRACKET
26 1 - - - - - - 12 - .042 CAP TUBE
27 4 A0024 10-24 X 3/8 TH, SCREW
28 1 S1333 EVAPORATOR ASSY.
29 1 S0509 ACCUMULATOR
30 5 S1204 EVAPRATOR RETAINER PINS
9

CONCEPT JR, continued
SYM
QTY
PART NO.
DESCRIPTION
31 1 S1206 WATER COIL RETAINER BRACKET
32 1 S0835 AGITATOR PUMP
33 1 S1306-LG AGITATOR PUMP BRACKET
34 2 F0004 SCREW, #8 X 1/2 PH HD SELF TAPPING
35 1 S1244 SNAP IN RECEPTACLE
36 1 S0276 TRANSFORMER, 40 VA, 120 VOLT/24 VOLT
37 2 H0021 HOLE PLUG
38
3
S0046
BUSHING
39 4 S1335 TERMINAL BOARD SPACER
40 1 S1309 TERMINAL BOARD
41
1
S1210
CONTROL BOX COVER
42
1
S0766
UNIT ON/OFF SWITCH
43 1 A0017 GROUND SCREW, #8 X 1/2 INDENTED HEX SLOT
44 1 E0664 STRAIN RELIEF
45 1 S1209 CONTROL BOX
46
1
S1207-4
VALVE HOUSING
47 1 S0768 SWITCH LOCK
48 2 S0768-K KEY ONLY, SWITCH LOCK
49 4 S1313 VALVE SWITCH, PUSH HERE
50 1 S1208-4 VALVE MOUNTING PLATE
51 1 S1334 WATER COIL
52 4 PFC-II VALVE
53 1 S1211 STANDPIPE, 8 3/16"
54 1 S1205 WRAPPER & BUCKET ASSY W/INSULATION
55 1 S1215 CUP REST
56 1 S1214 DRAIN PAN W/CUP REST
57 1 SET S0743 DRAIN PAN HARDWARE, SET
58 1 E0141-12 ELECTRICAL POWER CORD
59 1 SET S0765 LEGS
10

INTERNATIONAL CARBONIC INC.
ADELANTO, CALIFORNIA
TITLE
DATE
DRN. BY
CHK. BY
APPR. BY
PFC-II-PP
1/26/00
GLW
I
C
I
3
7
9
PFC-II-Peristaltic Pump
1
2
4
5
6
8
10
11 12
13
14 15
24
23
22
13
16 20
21
17
18
19
25
SYM QTY PART NO. DESCRIPTION
1 1 E-623 NUT, SOLENOID
21E-525 COIL, W/SHIELD, SOLENOID, 24 VAC
34E-1005 SCREW, RETAINER
4 1 E-739 FLUX PLATE
5 1 E-527 STEM, SOLENOID VALVE
6 2 E-1004 RETAINER, S.S.
7 1 E-135 METERING PIN
8 1 E-1024-M ADAPTER, FLO WASHER, MODIFIED
9 1 E-134 "O" RING, METERING PIN
10 1E-1013 "O" RING, SYRUP ADAPTOR
11 1E-730 PLUNGER & SPRING ASSEMBLY
12 1E-520 METERING PIN ADAPTOR ASSY, INCLUDES SYM 7,9, & 12
13 2E-531 GASKET, SOLENOID STEM
14 1S-1162-A FLANGE PLUG
15 1E-1008 "O" RING, SODA ADAPTOR
16 1E-580 BODY, PFC-II, TWIST LOCK
17 1E-471-FF SYRUP OUTLET TUBE
18 1E-102 "O" RING, NOZZLE
19 1E-581 NOZZLE, TWIST LOCK
20 4E-137 "O" RING
21 2E-1043 COLLET
22 1E-1042 VALVE BLOCK
23 1E-162 SCREW, TAP TIGHT
24 1E-1040 WIRE, LOCK, QUICK RELEASE
25 1E-1041 BLOCK, VALVE, ASSY., Q/R
PFC-II-PP
11

I NTERNATI ONAL CARBONI C I NC.
ADELANTO, CALI FORNI A
TITLE
DATE
DRN. BY
CHK. BY
APPR. BY
PFC- I I VALVE
12/18/98
GLW
I
C
I
6
1
2
3
4
5
7
8
9
10
11
12
13
14 15
21
22 23
18
20
17
17
23
24 29
26
27
28
9
10
30
14
14
1
9
31
15
32
33
12
34
35
36
10
16
25
19
12

PFC-II
SYM
QTY
PART NO.
DESCRIPTION
1
2
E-623
NUT, SOLENOID
2
2
E-525 COIL, W/SHIELD, SOLENOID, 24 VAC
3
2
4
2
E-739
FLUX PLATE
5
2
E-527
STEM, SOLENOID VALVE
6
1
E-456
ESCUTCHEON PLATE (1/2 PLATE)
7
2
E-730
PLUNGER & SPRING ASSEMBLY
8
2
E-531
GASKET, SOLENOID STEM
9
4
E-1005
SCREW, RETAINER
10
2
E-1004
RETAINER, S.S.
11
2
E-135
METERING PIN
12
2
E-134
"O" RING, METERING PIN
13
2
E-520
METERING PIN ADAPTOR ASSY, INCLUDES SYM 11, 12, & 13
14
1
E-1008
"O" RING, SODA ADAPTOR
15
1
E-1013
"O" RING, SYRUP ADAPTOR
16
1
E-554-A
CAP, COVERALL, SHORT
17
2
E-385
TUBING, INLET ASSY., 1/4" HOSE, S.S. 90 DEGREE
18
2
E-162
SCREW, TAP TIGHT
19
2
E-137
"O" RING, TUBE INLET
20
1
E-240
1/2 SCREW
21
1
E-358
ARM, ACTUATING
22
1
E-157
SWITCH, SUB MINIATURE
23
1
E-188
SPRING, W/INSULATOR PAD
24
***
E-157-A
SWITCH, SUB MINIATURE, DUAL (OPTIONAL)
25
1
E-580-P
VALVE BODY, WITH DRIVE PINS
26
1
E-471-FF
SYRUP OUTLET TUBE
27
1
E-102
"O" RING, NOZZLE
28
1
E-581
NOZZLE, TWIST LOCK
***
E-581-FF
NOZZLE, TWIST LOCK, FAST FLOW
29
***
E-258
ARM, ACTUATING, DUAL, LONG (OPTIONAL)
30
***
E-1024
FLOW WASHER ADAPTER
31
***
E-1003
HOUSING, W/SODA DECAL
***
E-1010
HOUSING, W/SYRUP DECAL
32
***
E-1022
FLOW WASHER, STANDARD FLOW
***
E-1023
FLOW WASHER, FAST FLOW
33
***
E-1002
ADJUSTING SCREW, W/"O" RING
34
***
E-1006
SPRING, SODA
***
E-1011
SPRING, SYRUP
35
***
E-1007
PISTON & CYLINDER, SODA, (MATCHED SET)
***
E-1012
PISTON & CYLINDER, SYRUP, (MATCHED SET)
36
***
E-1016
"O" RING, BOTTOM SEALING
***
OPTIONAL, SPECIFY
13

I NTERNATI ONAL CARBONI C I NC.
ADELANTO, CALI FORNI A
TITLE DATE DRN. BY CHK. BY APPR. BY
PPM ELECTRICAL SCHEMATI C
12/14/04
G. L. WHEELER
I
C
I
C NO NC
COLORED BLACK
WATER COI L
110 VOLT
WHITE
BLACK
THREE PIN CONNECTOR TO VALVE
FROM VALVE
POTENTIOMETER
KEY SWITCH
ON/OFF SWITCH
RI BBED
NON- RI BBED
BLACK FROM COI L
BLACK FROM COI L
TRANSFORMER 24 VAC
31
C
S R
M
S
1
FAN MOTOR
COMPRESSOR
1 2 3 4 5 6
6 65
5 54
4 4
3 3 3
2 2 2
1 1 1
6
A
B
C
D
COMPRESSOR
COMPRESSOR RIBBED
AGITATOR MOTOR
GROUND SCREW
TERMINALS ON ROW C MUST BE COMMONL Y GROUNDED TO CABINET
ICE BANK CONTROL
ORANGE
BLUE
WHITE
TRANSFORMER 110 VAC
RIBBED
NON-RIBBED
BLACK
WHITE
BROWN BLUE
RIBBED
NON-RIBBED
COLORED
WHITE
COLORED
BLACK
BLACK RIBBED
BLACK
WHITE
14

1 2 3 4 5 6
6
65
5
54
4
4
3
3
3
2
2
2
1
1
1
6
A
B
C
D
INTERNATIONAL CARBONIC INC.
ADELANTO, CALI FORNI A
TI TLE
DATE
DRN. BY
CHK. BY
APPR. BY
S-1309 ELECTRICAL
SCHEMATIC
12/14/04
GLW
I
C
I
GLW
GLW
GROUND TERMINAL
SCREW IN CONTROL
BOX
GREEN
GREEN
GREEN
GREEN
GREEN
WHI TE
WHI TE
WHI TE
WHI TE
WHI TE
BLACKBLACK BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK RI BBED
ILLUMINATION (OPTIONAL)
BLACK
BLACK
ON/OFF
SWITCH
ICE BANK
CONTROL
CONDENSING UNIT
S
C
R
M
S1
31
FAN MOTOR
COMPRESSOR
110 VAC
C
NO
NC
24 VOLT
BLACK
WHITE
SYRUP
WATER
SINGLE
15

S-1737 ASSEMBLY
S-1698 - PLASTIC CLAMP
MITYFLEX NOR-6F-250 S-1722
S-1739-C HOUSING/COVER
S-1740 - ROLLER ASSY.
S-1739-H PUMP HOUSING BODY
S-1738 - MOTOR/GEAR BOX ASSY
S-1699 - POTENTIOMETER
S-1742 - SHEET METAL BASE
S-1741 - CONTROLLER
S-1335 - PLASTIC STANDOFF
6-32 X 3/4 PH S.S.
8-32 X 3/8" PH S.S.
PLASTIC WASHER
8/01
16

S-1743 REPLACEMENT ASSEMBLY
S-1739-C HOUSING/COVER
S-1739-H PUMP HOUSING BODY
S-1738 - MOTOR/GEAR BOX ASSY.
S-1742 - SHEET METAL BASE
S-1335 - PLASTIC STANDOFF
6-32 X 3/4 PH S.S.
S-1740 - ROLLER ASSY.
8-32 X 3/8" PH S.S.
PLASTIC WASHER
MITYFLEX NOR-6F-250 S-1722
8/01
17