Intex Quick-Fill AP642 User manual

166
IO
(166IO) AP642 ELECTRIC PUMP ENGLISH 4.875” X 7.25” 05/23/2019
SAVE THESE INSTRUCTIONS
Page 1
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
INTEX®OWNER'S MANUAL
Quick-Fill™ Electric Air Pump, Model AP642
220 – 240 Volt ~ 50 Hz; 12 Volt DC; Rechargeable Battery
166-*IO-R0-2005
•Adult use only.
•Do not drop unit into water or expose unit to rain or water.
•Do not direct air stream at face or body.
•Do not operate for more than 10 minutes at a time. Unplug and let cool at least
30 minutes.
•Unplug unit when not in use.
•Do not obstruct vent holes or open source.
•Do not insert objects into the inflation or deflation connector.
•To reduce the risk of electric shock, do not expose to rain. Store indoors.
•This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
• The appliance is only to be used with the power supply unit provided with the
appliance. It must only be supplied at safety extra low voltage corresponding to the
marking on the appliance.
• Charging operations shall be carried out in accordance with the instructions provided
herewith, see section “CHARGE/RECHARGE INSTRUCTIONS”.
FOLLOW THESE RULES AND ALL INSTRUCTIONS TO AVOID PROPERTY
DAMAGE, ELECTRIC SHOCK, BURNS OR OTHER INJURY.
WARNING

166
IO
(166IO) AP642 ELECTRIC PUMP ENGLISH 4.875” X 7.25” 05/23/2019
SAVE THESE INSTRUCTIONS
Page 2
PARTS DESCRIPTION:
1. PUMP
2. INFLATION CONNECTOR
3. DEFLATION CONNECTOR
4. SWITCH
5. DETACHABLE 12V DC
POWER CORD
6. AC ADAPTER
7. NOZZLES
8. SWITCH OPERATION DETAIL
9. VENT HOLES / SLOTS
Inflate and deflate
with batteries.
Inflate and deflate
with DC power.
Inflation OFF and recharge mode ON with AC or DC power.
8
9
1
2
5
6
3
4
NAMES OF PARTS
7
INSTRUCTIONS
General
• Pump must be charged before use and is not designed for inflation directly from household AC
power sources.
• Itisrecommendedthatthefirstchargetobe10hoursorovernightusingtheACadapterpoweredby
household 220-240 AC voltage.
• Ifnecessary,theinitialchargecanbemadeusingtheDCpowerCordpluggedintoanautomobile
cigarette lighter or 12V DC accessory receptacle for one hour. After the first charge, it may be used
for inflation (without cords) and recharged using either the AC Adapter or Fast-charged (1 hour only)
using the 12 Volt DC Power Cord. See specific instructions below.
• Theexternalflexiblecableorcordofthistransformercannotbereplaced.Ifthecordisdamaged,
the transformer shall be scrapped.
• The“ ” position turns the pump OFF and is also the RECHARGE mode position.
• Thebatteriesarepermanentlysealedinthepumpandcannotberemovedorreplaced.Asthepump
weakens from use, recharge the batteries. Do not wait until they are fully discharged.
• This product contains sealed non-replaceable nickel metal-hydride (Ni-MH) rechargeable batteries.
Do not dispose of the product in regular trash, municipal waste stream or by fire as the built-in
rechargeable battery may leak or explode. Always dispose of the batteries safely in accordance with
your local law and regulations.
• Thebatterymustberemovedfromtheappliancebeforeitisscrapped.
• Theappliancemustbedisconnectedfromthesupplymainswhenremovingthebattery.
• Keep away from heat or direct sunlight.
•Return pump, DC power cord, AC adapter and nozzles to package when not in use.
• Nospecificairpumpmaintenanceisrequired.

166
IO
(166IO) AP642 ELECTRIC PUMP ENGLISH 4.875” X 7.25” 05/23/2019
CHARGE/RECHARGE INSTRUCTIONS
Charging the pump by AC adapter using household 220-240 AC voltage:
1. The pump must be charged for 10 hours or overnight with AC adapter powered by
household 220-240 AC voltage.
2. Plug the AC adapter power cord into the air pump power receptacle (FIG. 1).
3. Plug the other end of the AC adapter power cord into a household 220-240 Volt AC
electrical outlet (FIG. 2).
4. Slide the switch to “ ” position to charge/recharge the batteries (FIG. 3).
5. Initial Charge: Charge the pump for ten (10) hours or overnight with household AC
voltage.
6. When the pump is fully charged, remove the power cord (FIG. 4).
Charging the pump using a standard automobile 12 Volt
DC power source:
1. The pump must be charged for 1 hour with 12 Volt DC
power source.
2. Plug the 12 Volt DC power cord into the air pump power receptacle (FIG. 5).
3. Attach the DC power cord plug into a standard 12 Volt DC automobile cigarette lighter
or 12V DC accessory outlet (FIG. 5).
4. Slide the switch to “ ” position to charge/recharge the batteries (FIG. 3).
5. Charge: Charge the pump for 1 hour with 12 Volt DC power source.
6. When the pump is charged, immediately remove the power cord.
NOTE: The LED light turns red during charging/recharging mode. If the LED light does
not light up, make sure the switch is in the “ ” position.
SAVE THESE INSTRUCTIONS
Page 3
FIG (3)
220~240V 110~120V
FIG (2)
√
FIG (1) FIG (4)
FIG (5)

166
IO
(166IO) AP642 ELECTRIC PUMP ENGLISH 4.875” X 7.25” 05/23/2019
Inflation using the 12 Volt DC power cord:
1. Plug the 12 Volt DC power cord into the air pump power receptacle (FIG. 5).
2. Attach the DC power cord plug into a standard 12 Volt DC automobile cigarette lighter or accessory outlet (FIG. 5).
3. Attach the air pump inflation connector with nozzle if appropriate to the inflation valve on the item to be inflated (FIG. 7).
4. Slide the switch to “ ” position to operate the air pump (FIG. 8). Inflate item to desired level.
5. When the item is inflated, slide the switch to “ ” position to turn off the air pump (FIG. 3). Immediately unplug air
pump and cords when air pump is not in use.
Inflation using the air pump when fully charged (without power cord):
1. Attach the air pump inflation connector with nozzle if appropriate to the inflation valve on the item
to be inflated.
2. Slide the switch to “ ” position to operate the air pump (FIG. 9). Inflate item to desired level.
3. When the item is inflated, slide the switch to “ ” position to turn off the air pump.
DEFLATION
Deflation using the 12 Volt DC power cord:
1. Follow steps 1 & 2 under DC power inflation instructions.
2. Attach the air pump deflation connector with nozzle if appropriate
to the deflation valve on the item to be deflated (FIG. 10).
3. Slide the switch to “ ” position to operate the air pump. Deflate item to desired level.
4. When the item is deflated, slide the switch to “ ” position to turn off the air pump (FIG. 3). Immediately unplug air
pump and remove the cord when air pump is not in use.
Deflation using the air pump when fully charged (without power cord):
1. Attach the air pump deflation connector with nozzle if appropriate into the deflation valve on the item to be deflated.
2. Slide the switch to “ ” position to operate the air pump. Deflate item to desired level.
3. When the item is deflated, slide the switch to “ ” position to turn off the air pump.
FIG (9)
SAVE THESE INSTRUCTIONS
Page 4
©2019 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Recreation Corp. All rights reserved/Tous droits réservés/Todos los derechos
reservados/Alle Rechte vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™Trademarksusedinsomecountriesoftheworldunderlicensefrom/®™Marquesutiliséesdanscertainspayssouslicencede/Marcasregistradas
utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex
Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801•DistributedintheEuropeanUnion
by/Distribuédansl’UnionEuropéennepar/DistribuidoenlauniónEuropeapor/VertriebinderEuropäischenUniondurch/Intex Trading B.V., Venneveld 9, 4705
RR Roosendaal – The Netherlands
www.intexcorp.com
OR
FIG (8)
FIG (7)
FIG (10)
INFLATION
When inflating large items such as inflatable boats and large air mattresses,
no accessory nozzle (FIG. 6) may be needed. The air pumps inflation connector
may fit directly into the inflation valve. If a nozzle is needed, use the air pump
nozzle most appropriately sized for the product, then follow the instructions below:
FIG (6)