Invacare rea clematis User manual

Clematis®
User Manual
English

2CLEMATIS®

CLEMATIS®3
Contents
Parts of the wheelchair 4
Product description 5
Intended use 5
General information 6
Caution and warning 7
Lifting the wheelchair 7
Product information 8
Upholstery 8
And frame colours 8
Accessories 8
Technical data 9
Assembly 10
Settings 13
Legrests 13
Footplates/calf pads 14
Armrests 14
Carer-operated angle adjustment 15
Height adjustable push handles 16
Height adjustment back 16
Anti-tip devices 17
Brake 17
Carer-operated brakes 18
Seat depth adjustment 18
Balance and stability 19
Seat heights 20
Accessories 21
Trunk supports 21
Trunk support swing away 22
Pelvic belt 23
Abduction cushion 24
Transporting wheelchairs with users in vehicles 25
Crash test protocol rea clematis 26
Restraint methods 27
How to dissasemble your clematis to transport it as luggage 28
Safety instructions/propelling techniques 30
Guarantee 32
Maintenance 32
Recycling 33
Surface treatment 33

6
9
2
7
8
1
4
10
3
5
4CLEMATIS®
Parts of the wheelchair
1. Frame, lower section
2. Seat frame
3. Backrest
4. Push handles
5. Seat
6. Rear wheel
7 Castors
8. Step tube/Anti-tip device
9. Armrests
10. Legrests

CLEMATIS®5
Product description
REA™ CLEMATIS®
The Rea™ Clematis®’s seat frame, push handles and certain other com-
ponents subjected to strain are made of steel. Legrests are made of high
quality aluminium.
Castor suspension and the jointed parts of the frame are made of polyamide
reinforced with fibreglass. The backrest plate is also made of polyamide
reinforced with fibreglass. Plastic details are marked for recycling. Seat and
backrest cushions are made of foam rubber and the upholstery is made of
washable plush or elastic polyurethane cloth.
The Rea™ Clematis® is a carer-operated wheelchair with an angle-adjus-
table seat unit. The angle of the backrest unit can be adjusted independently
of the seat. The controls for the seat and backrest angle adjustment are
included on the push handles. The Rea™ Clematis® is available in three
seat widths. The armrest height of each chair can be adjusted.
The wheels can be pneumatic or semi solid.
The seat and backrest pads have been ergonomically designed for the user.
They are to provide as much stability and comfort as possible, as well as
good pressure distribution.
The Rea™Clematis® is a manual wheelchair, intended for users who have
a low level of activity and who sit in the wheelchair for long periods. The
comprehensive comfort and stability provided by the backrest and the option
of seat unit and backrest angle adjustment provide the user with relaxed and
comfortable rest.
• Regarding both operation and manual adjustment of the seat unit the
Rea™Clematis® is intended for operation by the carer.
• The Rea™Clematis® must be used with its seat and backrest pads.
• The max. user weight is 125 kg.
• The service life of the chair depends on its application, the user’s degree
of activity as well as care and maintenance.
Intended use

6CLEMATIS®
Invacare®is only responsible for product changes carried
out by personnel who we authorise. We reserve the right
to make any changes to equipment and specifications with-
out prior notice.
Rea™Clematis® is a wheelchair with many adjustment options and accessories.
To ensure that you benefit as much as possible from Rea™Clematis®, and in
order to do it's options justice, the chair must be tested and adjusted by compe-
tent personnel. We hope that you have also received instructions for using your
Rea™Clematis® in everyday life.
This manual includes a description of the parts of the chair, simple adjustment
options, how to use the Rea Clematis® safely and how to transport it. The
manual must be read thoroughly before the chair is used.
Also included in this manual is a description of how the accessories are fitted and
slightly more advanced settings.
As the Rea™Clematis® has many different components and accessories, the
appearance of the accessories you have for your chair may differ from those
shown.
Check that all components match the delivery note. Any
transport damage must be reported immediately to the
transport company. Remember to keep the packaging
until the transport company has checked the goods and a
settlement has been reached.
General information
Delivery check
NB!
Check that the following parts are securely fitted and
operational on the wheelchair:
• Wheels
• Backrest
• Anti-tip device
• Push handles
• Footrests
Daily performance check

CLEMATIS®7
Always lift the wheelchair by gripping the frame at the
points shown in the diagram. Never lift the wheelchair
by the removable armrests or the foot-rests. Ensure
that the backrest and push handles are securely in
place. Also read the chapter: Safety instructions/
propelling techniques.
CAUTION AND WARNING
Failure to comply with instructions given may result
in personal injury and/or product damage.
• Check the following points before the wheel-
chair is used:
– all parts are securely fastened to the frame.
– all handles and knobs are properly tightened.
–
that all brakes and anti-tip devices function
correctly
• Never lift the chair by the removable armrests,
or by the footrests. Ensure that the backrest and
push bar are securely fastened to the chair.
• Remember that with every alteration to the
chair’s balance the inclination to tip, forwards or
backwards, also changes.
• When fitting accessories etc. always take care
not to trap your fingers.
• There is always an increased risk of trapping
parts of your body when tilting the wheelchair’s
back and seat.
• The width of the seat should never be adjusted
so much so that the inside of the armrests press
against the side of the pelvis.
• Apply the brake whenever the occupant is to be
moved into or out of the chair.
• Never stand on the footplates when getting in
or out of the chair, because of the risk of tip-
ping over.
• We recommend that the chair should be fitted
with castor adapters when the seat is located in
its most forward position.
• The handrims may become hot due to friction, and
this may cause injury to your hands.
• Remember that the effectiveness of the carer-
operated brake is reduced in wet and slippery
conditions, as well as when on a slope.
• Be careful to ensure that the drive wheels are
securely attached.
• Drive wheels are not to be detached while the
user is sitting in the chair.
• Surfaces of the wheelchair like frame parts or
upholstery can reach temperature
> 41 degrees C if they have been exposed to the
sun during a longer period of time. .
LIFTING THE WHEELCHAIR
This symbol means warning
and is used throughout the
manual for information that
needs special attention

8CLEMATIS®
Rea™Clematis® has a wide range of accessories and options. Some of the
accessories may not be available in all countries.
Castors 200 mm and 150 mm solid
Rear wheels 12", 22", 24"
Other Trunk supports
Pelvic belt
Abduction Cushion
Arm rest spacer
Clamp for intravenous drip
Table Tray
Locking device for table tray
ACCESSORIES
Product information
Upholstery Grey Dartex TR23
Frame colours Pearl grey
UPHOLSTERY
AND FRAME COLOURS
Seat width 39, 44, 49 cm
Seat depth 42-48 cm
Backrest height 55 cm

CLEMATIS®9
Technical data – Rea™Clematis®
39, 44, 49 cm
+ 2 cm with the
spacers
42-48 cm 40–45 cm*1 60-71 cm *1,2 23–34 cm *1
40–52 cm -1°– +19° Seat width + 21 cm 96-112 cm*2 112–148 cm
Max 125 kg Transport weight
20,5/21/21,5kg.*3
-1° – +32° 30, 32, 33,5 kg Transportation
dimensions *4
* 1 : Measured from seat plate
* 2 : Excluding neckrest and push handles
*3: Without rear wheels, neckrest, armrests,
legrests, trunk support and seat cushion
* 4: Width 39 (h 59.5 x L 84 x 58.5 cm)
Width 44 (h 59,5 x L 84 x 63,5 cm)
Width 49 (h 59,5 x L 84 x 68,5 cm)
30, 32, 33,5 kg

10 CLEMATIS®
1a.
1b.
C
1c.
B
A
2. 2. Armrests
The armrests are fitted onto the wheelchair by
pushing them down into their attachments on
the edge of the chair seat.
Assembly
When you receive your wheelchair, you must fit the
backrest into place and fit the neckrest, armrests and
legrests onto the chair. The assembly is simple and
does not require any tools.
1a. Fitting and securing the backrest
Unfold the backrest into an upright position.
1b. Secure the piston (A) using the pin (B).
1c. Lock the pin using the lock shackle/loop (C).
Check that the shackle/loop is securely
locked.

B
4. C
A
D
3a.
3b.
E
CLEMATIS®11
3b.
Lock the legrests by turning them inwards. The
legrests are automatically locked so there is no
risk of them coming off the wheelchair.
Be careful not to trap your fingers between
frame and legrest.
3a. Legrests
Attach the legrests by pushing the tube at the
upper part of the legrests down into the tubes
on the wheelchair. You must angle the legrests
outwards when inserting them.
4. Neckrest
You attach the neckrest by putting it into the
reciver on the backrest and fasten it with the
knob (B).
Adjust the position with the lever (A) and nuts
(C). Adjust the height by loosening the knob (B).
Part (E) is a memory function for the height of the
neckrest. When the desired height is achieved,
loosen the screw on the memory and lower it
towards the back. Fasten the screw again.
Pay attention to how far the neckrest is raised.
If the red marking (D) is visible, the neckrest
is raised too high.

5.
A
B
C
D
E
12 CLEMATIS®
5. Headrest
You attach the neckrest by putting it into the
reciver on the backrest and fasten it with the
knob (B).
Adjust the position with the lever (A) and nuts
(C). Adjust the height by loosening the knob (B).
Part (E) is a memory function for the height of the
neckrest. When the desired height is achieved,
loosen the screw on the memory and lower it
towards the back. Fasten the screw again.
Pay attention to how far the headrest is raised.
If the red marking (D) is visible, the headrest
is raised too high.

1.
C
B
A
2.
CLEMATIS®13
Settings
LEGRESTS
Angle adjustable legrests support the legs and reduce
pressure. The legrests can be used for bandaged legs,
but not for legs in plaster casts. The legrests must
always be fitted with calf pads, footplates and heel
straps.
It is important to adjust the height and angle of the
legrests to obtain a good seating position.
1. Height adjustment
Loosen screw (A) with an Allen key. Adjust the
legrest into a suitable height and the screw is
caught by one of the recesses on the legrest tube.
Then retighten the screw.
2. Angle adjustment
Pull the lever (B) with one hand while support-
ing the legrest with your other hand. When a
suitable angle is obtained, let go of the lever and
the legrest will look into one of seven preset
positions (C).
Do not place anything heavy, or let children
sit on the legrest. It may cause damage to the
mechanism.
The distance between the lowest part of
the footrest and the ground must be at least
40 mm.
Tools: 5 mm Allen key.

1.
A
B
A
B
D
C
2.
1.
14 CLEMATIS®
The armrest has an auto-lock. Press the spring (B)
before removing the armrest.
1. Armrest height
The height of the armrest can be adjusted by
loosening the screw (A) with an Allen key. Adjust
to the desired height and retighten screw.
If armrest is adjusted too low it will conflict with
the rearwheel when tilting the seat unit.
When adjusting the height, do not put your
fingers between armrest pad and side plate as
they may get trapped.
Tools: 5 mm Allen Key
1. Angle-adjustable footplates
Adjust the angle and the depth by loosening the
screw (A) at the footplate attachment with a 5
mm Allen key. Adjust the footplate to the correct
position and retighten the screw.
Do not place anything on the footplate
when the screw is loose.
2. Calf pads
The calf pads can be fitted in four different depth
positions. Swing the pad forwards. Unscrew screw
(B) using an Allen key. Remove the large nut (C) on
the reverse side and place it in the other attach-
ment hole. Move the calf pad to the new position
and secure it into place with the screw.
The height of the calf pads can easily be adjusted
using the handwheel (D).
Tools: 5 mm Allen key.
Tools: 5 mm Allen Key
FOOTPLATES/CALF PADS
ARMRESTS

1.
2.
3.
A
B
4.
C
D
CLEMATIS®15
2. Tilt adjustment
Tilt of the seat unit (seat and backrest) by pull-
ing the green right-hand lever (B) upwards and
keeping it there whilst you tilt the seat unit to the
required position. Release the lever (B).
Seat unit
1. Backrest angle adjustment
Adjust the angle of the backrest by pulling the
yellow left-hand lever (A) upwards and keeping
it there whilst you push the backrest away from
you or pull it towards you until you have obtained
the required position. Release the lever (A).
CARER-OPERATED ANGLE ADJUSTMENT
The wheelchair is equipped with carer-operated controls. You can adjust the angle of the backrest forwards
or backwards and tilt the whole seat unit including the backrest. These two functions can either be controlled
manually or electrically.
2.Tilt lock
The tilt lock (C) allows you to set the tilting of
the seat unit and/or the angling of the backrest
to a fixed position. Tilt and/or angle the seat and
backrest to the desired position and insert the
tilt lock. The position is now set and cannot be
changed.
The tilt lock is removed by pressing the plastic peg
(D) with a small object while pulling out the tilt
lock.
Be careful that you do not trap your finger
between the seat and the armrest attachment
(picture 3).

B
C
D
16 CLEMATIS®
HEIGHT ADJUSTMENT BACK
HEIGHT ADJUSTABLE PUSH HANDLES
Adjust the height of the push handles
(90 mm) by loosening the handle wheels (B). Adjust
the push handles to one of the four positions, then
retighten the handle wheels (B).
After adjusting the push handles, always make sure
that the handle wheels are properly retighten.
The height of the back can be adjusted variably. Loosen
the four screws (C) and adjust the back to the desired
height. Brackets (D) should be placed as high up as
possible. Re-tighten the screws firmly.
Tools: 5 mm Allen key.

A
B
C
1.
1.
2.
A
CLEMATIS®17
The anti-tip devices also act as step tubes. They are
height-adjustable and can easily be set in six different
positions.
Adjust the anti-tip devices by pressing the spring-
loaded buttons (A) and then raising or lowering the
anti-tip devices until you obtain the required posi-
tion.
Ensure that both anti-tip devices are adjusted
to the same position and that the spring-
loaded buttons pop back into place in their
new position.
ANTI-TIP DEVICES
BRAKE
1. This type of brake is to be used when the wheel-
chair is stationary and is not intended to be used
for reducing the speed.
To apply the brake of the wheelchair, move the
lever backwards. To release the brake, move the
lever forwards.
Take care not to trap your fingers between the
brake pin and tyre.
Tools: 5 mm Allen key
2. To obtain the correct braking effect, the brake
pin (B) is to press into the tyre when you apply
the brake. The brake may therefore need to be
adjusted. Loosen the screw (A) and move the
brake to the required position. Retighten the
screw. There is to be a distance of 15 mm between
pin (B) and tyre (C).
Incorrect setting or incorrect use of the brake
reduces the brake effect.

1.
2.
3.
A
A
18 CLEMATIS®
CARER-OPERATED BRAKES
1. Brake when the wheelchair is moving: squeeze
both brake handles upwards and the brake will
be applied.
2. Lock the brakes: squeeze the handle upwards
and move the lock catch (A) upwards. Then
release the handle.
3. Release the brakes: squeeze the handle upwards
and the lock catch will release automatically.
Incorrect setting or use of the brakes will
reduce the braking effect.
SEAT DEPTH ADJUSTMENT
Adjust the seat depth by loosening the two screws
(A). Push or pull the seat backwards (30 mm) or
forwards (30 mm) to reach the wanted position. Re-
tighten the screws.
Tools: 5 mm Allen key

1–2.
A
D
B II B III
A
B
F
C
B
3.
E
A
A II A III
CLEMATIS®19
Check the stability with the user in the chair when the
chair has been adjusted. Adjust the angle of the seat and
backrest backwards to their maximum setting. Check
the risk of tipping. Re-adjust the balance of the chair
and/or anti-tip devices to obtain a chair that is stable
in all situations.
By moving the seating section (seat plus backrest) either
backwards or forwards, in relation to the lower frame
(and also in relation to the rear wheel and castors) you
also alter the chairs manoeuvrability and stability.
If the seating section is located in the forward posi-
tion (III) the chair is more stable (in regard to tip-
ping backwards), though slightly less manoeuvrable.
However, the chair also becomes somewhat more
susceptible to tipping forwards. If the seating section
is located in the rear position (II) the chair becomes
more manoeuvrable, though somewhat less stable (in
regard to tipping backwards). This can be countered
by lowering the anti-tip device, with which the chair is
fitted. Subsequently, you have a wheelchair that is both
manoeuvrable and safe.
If you want to alter the balance of the wheelchair it is
necessary to adjust the two fittings (A) and position of
gas piston (B) on frame bracket.. The two fittings are
used to move the chairs seating section forwards and
backwards and the gas piston enable you to move the
fitting for the chairs angle adjustment mechanism.
It is important that the two fittings and the gas piston
are adjusted and secured in the same relative positions
(table 3).
1. Adjust the upper attachment.
Take away the seat cushion, seat plate, legrests and
wheels. Put the chair with it's front facing down.
Adjust each of the fittings in this way: Slacken the
screw (C) on the upper side of the fitting by a
couple of turns, but do not unscrew it completely.
Unscrew screw (D) and turn the fitting until the
correct position ( II or III) is aligned with the screw
hole in the frame and then re-tighten screw (D).
Then, re-tighten screw (C).
NB – Never touch screw (E)!
2. Adjust the lower attachment.
Pull out pin (F) on the gas piston by opening clamp
and put the gas piston in position. For the right
position, see table (3).
NB – Be sure the pin is secured again with
clamp.
NB – There is a greater risk of tipping forward
when the seat is extended to the front.
Each setting can be adjusted in two ways:
II = easy to manoeuvre, less stable
III = stable chair, less manoeuvrability
BALANCE AND STABILITY

45 24" 2 1 200
40 22" 1 3 150
45 12" 3 1 200
SH
1
2
3
20 CLEMATIS®
SEAT HEIGHTS