inVENTer iV14-Zero sMove User manual

iV14-Zero
sMove
Operating instructions

2
iV14-Zero ventilation system / sMove controller •Operating instructions
T             
inVENTer®, Xenion®, Inventin®, inVENTron®, and Clust-Air®are registered
trademarks of inVENTer GmbH.
The copyright of this document remains with the manufacturer.
Rights to all contents and images: © inVENTer GmbH 1999-2018.
All trademarks used in this document are the property of their respective
manufacturers and are hereby acknowledged.
Disclaimer
This documentation is a translation of the original German operating in-
structions. After completion of the installation it must be given to the user
(tenant, owner, property management, etc.). The content of this docu-
mentation has been checked for compliance with the described hard-
ware and software. Nevertheless deviations may still occur, therefore
no guarantee of compliance can be provided. This documentation de-
scribes the functionality of the standard scope. The documentation does
not purport to cover all details on all types of the product and cannot
cover every conceivable scenario for operation, cleaning and maintenance.
7KHLOOXVWUDWLRQVLQWKLVGRFXPHQWPD\GLႇHUVOLJKWO\IURPWKHGHVLJQRIWKH
product that you have purchased. The same functionality is ensured despite
any design deviations.
This documentation is updated regularly. Necessary corrections and ap-
propriate supplements are always included in subsequent editions.
<RXFDQ¿QGWKHODWHVWYHUVLRQDWwww.inventer.eu/downloads
Version 1.0

3 iV14-Zero ventilation system / sMove controller •Operating instructions
      
1 User and safety instructions .................................................................................................. 4
1.1 User information............................................................................................................... 4
1.2 Safety instructions............................................................................................................ 5
2 System overview ..................................................................................................................... 7
2.1 Construction..................................................................................................................... 8
2.2 Function ........................................................................................................................... 9
2.3 Control elements.............................................................................................................. 10
3 Operation of the iV14-Zero ventilation unit........................................................................... 11
3.1 Opening/closing the inner cover ...................................................................................... 11
3.2 Tilting the inner cover....................................................................................................... 11
4 Operating the sMove controllers ........................................................................................... 12
4.1 Design and features......................................................................................................... 12
4.2 Activating the controller.................................................................................................... 15
4.3 Setting mode.................................................................................................................... 16
4.4 Set output......................................................................................................................... 18
4.5 View hours run ................................................................................................................. 19
5 Cleaning and maintenance ..................................................................................................... 20
5.1 Remove the inner cover panel ......................................................................................... 21
 &OHDQLQJUHSODFLQJGXVW¿OWHUV.......................................................................................... 22
5.3 Removing the thermal accumulator insert ....................................................................... 23
5.4 Cleaning and reassembling the thermal accumulator insert............................................ 24
5.5 Attaching the inner cover ................................................................................................. 26
6 Troubleshooting and disposal ............................................................................................... 27
 6SHFL¿FDWLRQV .......................................................................................................................... 29
8 Accessories and spare parts.................................................................................................. 30
9 Guarantee and warranty ......................................................................................................... 32
10 Service...................................................................................................................................... 32
11 Appendix 1: Cleaning protocol .............................................................................................. 33
12 Appendix 2: Cleaning protocol .............................................................................................. 34
TABLE OF CONTENTS

4
USER AND SAFETY INSTRUCTIONS
iV14-Zero ventilation system / sMove controller •Operating instructions
1
User and safety instructions
Thank you for purchasing this high quality product from inVENTer!
Your inVENTer product is an exclusive system for the ventilation of your living premises, which
DGGLWLRQDOO\FRQWULEXWHVWRLPSURYLQJHQHUJ\HႈFLHQF\YLDWKHSULQFLSOHRIKHDWUHFRYHU\2XU
inVENTer ventilation units are made to the highest quality standards in Germany using premium
materials.
This section provides an overview of the basic safety precautions for safe and proper operation
of your ventilation unit.
1.1 User information
Concept of safety instructions
The safety and warning instructions in these operating instructions have a uniform structure
and are marked with a symbol on the left side of the instruction. A signal word in front of the text
also indicates the hazard level. If several hazard levels exist, the highest level safety instruction
is always used.
The safety and warning instructions contain the following information.
SIGNAL WORD: Type and origin of the hazard. Possible consequences of the hazard!
Measures to avoid the hazard.
A signal word indicates the severity of the potential hazard unless the preventative measures
are taken.
WARNING indicates: Imminent danger of serious injury or death.
CAUTIONLQGLFDWHV,PPLQHQWRUSRVVLEOHULVNRIPLQRUVLJQL¿FDQWLQMXU\
NOTICE indicates: Imminent or possible damage to property due to an adverse event/state.
If you see this sign, ensure you observe the described measures to prevent possible hazards
and/or damage.
Other symbols used in this documentation
In addition to the safety instructions, the following symbols are used:
A TIP symbol indicates practical and useful tips for handling your ventilation unit.
A tool symbol before an installation sequence lists any additional tools and materials
required for the described task.
A Red frame surrounding a graphic indicates that the interior wall is shown.
ŹAction required:WKLVUHTXLUHV\RXWRSHUIRUPDVSHFL¿FDFWLRQ
ÖCheck the results: this requires you to check the results of the action you have performed.

5
USER AND SAFETY INSTRUCTIONS
iV14-Zero ventilation system / sMove controller •Operating instructions

Safety instructions
These operating instructions are part of the ventilation unit and must be permanently available.
When handing the equipment/system to a third party, the operating instructions must be handed
over also. Please read the operating instructions carefully before operating or cleaning the
system and observe all information provided in this section about operating, cleaning and
maintaining your system. Also note the safety instructions that precede the described handling
instructions. Non-observance of safety warnings could result in injury and/or property damage.
Intended use
The ventilation unit is designed to ventilate dwellings and similar residential spaces.
It is controlled via an inVENTer system controller.
General instructions
• Use the equipment/system exclusively for the applications that are described in this docu-
mentation and only in conjunction with components that are recommended, authorised and
GHVFULEHGE\LQ9(17HU*PE+LQWKLVGRFXPHQWDWLRQ&KDQJHVRUPRGL¿FDWLRQVWRWKHHTXLS-
ment/system are not permitted.
• Your ventilation unit is exclusively designed for use in ambient temperatures between
-20 and 50 °C.
• Proper operation and cleaning/maintenance are required for trouble-free and safe operation
of the equipment/system.
• WARNING:,QVWDOODSUHVVXUHPRQLWRULQURRPVZLWKRSHQÀXHV,QDQ\FDVHDLUH[FKDQJH
PXVWEHDVVXUHGWREHVXႈFLHQWIRUWKHYHQWLODWLRQXQLWVDVZHOODVWKH¿UHSODFH
Consult your chimney sweeper and/or building planner before installation!
• NOTICE: Do not place the unit near radiators, room thermostats or in the immediate vicinity/
above sensitive paintings or furnitures.
• NOTICE: Maintain a minimum circumferential clearance of 250 mm to avoid the mixing of
outdoor air and exhaust air.
• NOTICE: Observe the predetermined minimum distance of 300 mm in front of the ventilation
unit to ensure access to the unit and its components. Remove/avoid obstacles that hinder
access to, or removal of, the unit’s components.
Cleaning and maintenance
• CAUTION: Operation and/or maintenance of the ventilation unit and its controllers
must not be carried out by children and/or persons who are not fully capable of doing
so due to their physical, sensory or mental capabilities, inexperience or lack of knowl-
edge. Young children should be supervised to ensure that they do not play with the
device.
• NOTICE: Your ventilation unit and controller have scratch-sensitive plastic surfaces. Do not
touch the inner cover with oily and/or dirty hands. Avoid contact with sharp or pointed objects,
e.g. rings.
• NOTICE: Do not use strong cleaning agents or solvents. Use a soft, damp cloth to clean the
plastic surfaces.
• NOTICE: Your inVENTer®ventilation unit operates with a protective low voltage and an
operating voltage of 6 – 16 V DC. The ventilation unit must not be connected directly to the
230 V power grid. It must always be connected via a controller.
• Before performing cleaning or maintenance tasks, disconnect the controller's power supply
and put on gloves.

6
USER AND SAFETY INSTRUCTIONS
iV14-Zero ventilation system / sMove controller •Operating instructions

1HYHUXVHWKHXQLWZLWKRXWWKH¿OWHUVDQGLQQHUFRYHU
• Use the sMove controllers exclusively to control inVENTer ventilation units with heat recovery.
If your ventilation unit has a defect, contact your nearest distributor or our technical service.
Any kind of use other than the intended use will exclude all liability claims.
Improper use
Any use that is not mentioned in the intended use section, is considered to be improper.
Do not install the equipment in areas which...
• Contain (or may contain) strong oils or lubricants.
• &RQWDLQRUPD\FRQWDLQÀDPPDEOHJDVHVOLTXLGVRUYDSRXUV
• Contain (or may contain) extreme dusts.
• Are exposed to ambient temperatures below -20 °C and above 50 °C.
• Contains obstacles that hinder access to, or removal of, the unit’s components.
• it is used to dry up the structure.
4XDOL¿HGSHUVRQQHO
The equipment/system may only be operated and maintained in conjunction with this documen-
tation and the documentation for the controllers.
Any necessary cleaning or maintenance tasks can be carried out by the user by following the
instructions. Operation and/or maintenance of the ventilation unit and controller must not be
carried out by children and/or persons who are not fully capable of doing so due to their
physical, sensory or mental capabilities, inexperience or lack of knowledge.
Conformity
The ventilation unit complies with the applicable technical safety requirements and standards
for household and similar electrical appliances. They are conform to the following European
directives:
• 2014/30/EC: Electromagnetic compatibility directive
• 2009/125/EC: Energy related products directive
• 2014/35/EC: Low voltage directive
• 2011/65/EC: Restriction of certain Hazardous Substances (RoHS) directive

7
SYSTEM OVERVIEW
iV14-Zero ventilation system / sMove controller •Operating instructions
2
System overview
The iV14-Zero ventilation system is designed as a sound absorbing ventilation solution.
I !" #$% !& $ # #" ' ())* & % " + , !+ ())*& #" &#"' $ !- %" + *.$ # -/%* #$ 0 3 ).& !& 4 3 )!$& %" + ' .!& 
KRXVHVURRPVLQSXEOLFIDFLOLWLHVDQGZRUNURRPVLQRႈFHEXLOGLQJV,WLVXVXDOO\ORFDWHGLQWKH
exterior wall.
The construction of the iV14-Zero product range complies with the applicable European
regulations.
The ventilation unit iV14-Zero comprises a wall sleeve into which a thermal accumulator insert
is installed. A closable inner cover conceals the ventilation unit visually discreet on the interior
ZDOOVLGH7KHLQWHJUDWHG¿OWHUDVVXUHVWKDWQRSROOHQRUGXVWPD\HQWHUWKHLQWHULRUURRPIURP
outside. On the exterior wall a driving rain proof hood covers the unit.
A sound insulation coating made of Inventin
®
, a material specially developed for noise reduc-
tion, is inserted into the wall sleeve. Into the so lined wall sleeve the thermal accumulator,
and inVENTron
®
are mounted. inVENTron
®
FRQVLVWVRIWZRDLUÀRZRSWLPLVLQJJXLGLQJYDQHV
embedding the Xenion
®
reversible fan. The guiding vanes on both sides of the fan
!" & . (!& !/
-
¿FLHQWFDSDFLW\XWLOLVDWLRQDQGHYHQÀRZWKURXJKWKHWKHUPDODFFXPXODWRU The sound insulation
coating of Inventin as well as the unique design of Xenion's fan blades reduce sound passage
HႇHFWLYHO\
I #& 5)" ()$$ ! + #% )" ! )/ 3 ! / )$$ )
6#"' #" 789:
! (
®system controllers1):
• sMove s4 • sMove s8 • MZ-Home
ComponentsVHH¿JSDJH
• ,QQHUFRYHULQFOGXVW¿OWHURIFODVV*
• Thermal accumulator insert
(thermal accumulator, inVENTron®,
and sound insulation coating made of
Inventin®)
• Wall sleeve
• Exterior closures
• 3ROOHQPLFURDQGDFWLYDWHGFDUERQ¿OWHU
options available
• Sound and wind protection options
available as accessory
Models
• Standard version: iV14-Zero ventilation units with driving rain proof weather protection hood
Nova (white/grey/Nord/custom colour)
• Corner version: iV14-Zero ventilation units with ÀDWGXFWLQWHJUDWHGLQWRWKHWKHUPDOLQVXOD-
tion layer and reveal grille (white/grey/Nord/custom colour).
Due to the reveal grille in the window reveal the ventilation unit disappears subtly into the
external wall.

8
SYSTEM OVERVIEW
iV14-Zero ventilation system / sMove controller •Operating instructions

Construction
Figure 1: Overview of iV14-Zero ventilation unit
Komponenten
;
Protective hood base plate
2 Ring insert (pre-assembled)
3 Protectiv hood cover
Thermal accumulator insert
(Thermal accumulator, inVENTron,
Sound insulation coating made of Inventin)
Flair Zero inner cover
Exterior Closure:
standard version:
Nova Zero protective hood
Wall sleeve
N< => ?@ A<
1 Flat duct Corner Zero
2 Ring insert (pre-assembled)
3 Wall bracket (2 x)
4 Flat duct sliding sleeve
5 Reveal grille
Corner version:
5HYHDOJULOOHDQGÀDWGXFW
B
Wall sleeve R-D200
7 Fastening elements for inner cover
8 Recess for fan BUS (interior wall side)
9 Sound insulation coating
10 Thermal accumulator with insulation
11 Thermal accumulator handle
12 Standard guiding vane (broad)
13 Xenion reversible fan
14 Slim guiding vane (narrow)
15 Guiding vane knob
16 BUS plug connection
17 Inner cover base plate
18 Flair Zero insert (pre-assembled)
19 Inner cover panel
20 'XVW¿OWHURIFODVV*
21 Spacer (4 x)
&RUQHUÀDWGXFWDQGUHYHDOJULOOH
A
A
B
D
C
A
B
C
D
1
5
10
13
6
15
2
17
12
9
14
16
19
18
7
8
20
21 11
Standard version
Corner version
3
2
3
1
4

9
SYSTEM OVERVIEW
iV14-Zero ventilation system / sMove controller •Operating instructions

Function
The iV14-Zero ventilation system is used to provide ventilation for living rooms and bedrooms.
The combination of inVENTron, and sound insulation coating made of Inventin ensures optimum
KHDWUHFRYHU\ZLWKPLQLPXPVRXQGHPLVVLRQDQGPD[LPXPDLUÀRZ
The ventilation unit operates on the principle of heat
recovery by changing the direction of the fan. The
integrated thermal accumulator charges itself with heat
HQHUJ\IURPWKHURRPVDLUDVLWÀRZVWRWKHH[WHULRU
(extract air). After 70 seconds, each Xenion reversible
fan changes direction. When the reversible fan
changes direction, it releases the stored heat energy
into the incoming outside air (supply air).
For this principle to work correctly and to ensure the
room’s pressure stability the incoming air and extract
air volumes must match, i. e. two iV14-Zero ventilation units are required. These are operated in
pairs in push-pull operation: One ventilation unit works in supply air mode while the other works
in extract air mode at the same time.
iV14-Zero is characterised by its silent operation. The patented sound insulation concept is based
on a combination of the coating made of Inventin and the Xenion reversible fan. The sound
insulation coating absorbs acoustic waves from outside and the unit itself (sound passage and
ÀRZJHQHUDWHGVRXQG'XHWRWKHIDQEODGHVDUUDQJHPHQWDQGVWUXFWXUHWKHVRXQGSDVVDJHIURP
the exterior is reduced again.
Due to the Xenion reversible fan's high pressure built-up and active speed control (integrated
ZLQGVWDELOLVHUWKHDLUÀRZZLWKLQWKHV\VWHPLVNHSWQHDUO\FRQVWDQW7KXVWKHDLUÀRZ¶V
sensitivity to pressure variation meets the requirements of class S3 according to EN 13141-8
PD[DLUÀRZGHYLDWLRQDW3D
In order to ensure the full functioning of the ventilation system throughout the entire year, an
DGGLWLRQDOÀH[LEOHWHPSHUDWXUHVHQVRULVLQWHJUDWHGLQWRWKH;HQLRQUHYHUVLEOHIDQ7KLVPHD-
VXUHVWKHWHPSHUDWXUHRIWKHDLUÀRZ,IWKHWHPSHUDWXUHIDOOVEHORZ&WKHUHYHUVLEOHIDQ
is automatically switched to extract air mode for 4 cycles. This allows the thermal accumulator
to heat up again and prevents cooling of the interior due to cold drafts. During this phase, the
PRGHWKDWKDVEHHQVHWRQWKHFRQWUROOHULVLQHႇHFWLYH6XEVHTXHQWO\WKHFRQWUROOHUVZLWFKHVWKH
ventilation unit back to the originally selected mode.
$PXOWLXVHGXVW¿OWHURI¿OWHUFODVV*LVLQWHJUDWHGGLVFUHHWDQGHDV\RIDFFHVVLQWRWKHLQQHU
FRYHU,W¿OWHUVRႇUHOLDEO\GXVWVDVZHOODVDOOHUJHQLFSDUWLFOHVVXFKDVSROOHQIURPWKHDPELHQW
DLUEHIRUHLWFDQHQWHUOLYLQJVSDFHV'XVW¿OWHUVDUHVHDVRQLQGHSHQGHQW)RUVSHFLDOUHTXLUH-
PHQWVPLFURSROOHQDQGDFWLYDWHGFDUERQ¿OWHUVDUHDYDLODEOHDVDQRSWLRQ
A decentralised ventilation system is based on the free movement of air between individual
pairs of ventilation units. Therefore, internal doors must not have air-tight seals.
Ensure adequate air transfer measures: An air gap of about 10 mm below the door, unscrew the
hinges by 5 mm, use a ventilation grille or similar (cross ventilation).
The ventilation unit is controlled via one of the inVENTer system controllers. Depending on the
controller, operating modes and functions may be selected.
70 s

10
SYSTEM OVERVIEW
iV14-Zero ventilation system / sMove controller •Operating instructions
C
Control elements
sMove controller
The controllers from the sMove product range are electronic control units
for controlling the iV14-Zero ventilation units.
They are characterised by their timeless and slim design and a simple
touch-based operating concept.
The sMove controller is available in the s4 and s8 versions.
s4 is used to control up to four iV14-Zero ventilation units.
s8 is used to control up to eight iV14-Zero ventilation units.
%RWKYHUVLRQVDUHDYDLODEOHLQDÀDWDQGVWDQGDUGYHUVLRQ,QFRQWUDVWWRWKHÀDWYHUVLRQLQ
DGGLWLRQWRSDXVHPRGHWKHVWDQGDUGYHUVLRQSURYLGHVWKHRSWLRQWRVZLWFKRႇWKHYHQWLODWLRQ
unit completely.
The connected ventilation units can be controlled in the following modes:
• Heat recovery • Pause function
• &RQWLQXRXVYHQWLODWLRQ2ႇRQO\V0RYHVWDQGDUGYHUVLRQ
MZ-Home controller
The MZ-Home controller is an electronic control unit for controlling up to
16 iV14-Zero ventilation units.
Due to its unique and innovative Clust-Air technology (multi-zone control)
and its versatility MZ-Home controls up to four zones within the residential
unit. Thus, it ensures individual ventilation to each living area.
The MZ-Home controller consists of a control unit and at least one
(optional up to four) Clust-Air module(s). Each Clust-Air®module can
FRQWUROXSWRIRXUL9=HURYHQWLODWLRQXQLWVLQGLႇHUHQW]RQHVZLWKLQWKH
accommodation unit. For each zone, the operating mode and output level
can be set manually or via a 7-day timer.
The connected ventilation units can be controlled in the following modes:
• +HDWUHFRYHU\ 'HKXPLGL¿FDWLRQ
• &RQWLQXRXVYHQWLODWLRQ2ႇ3DXVHIXQFWLRQ
The sMove and MZ-Home controllers can be expanded with additional sensors. An external in-
terface allows the connection of a potential-free switching contact or integration into an existing
home automation system via an analogue input.
For detailed information see the separate operating instructions of the controller.

11
OPERATION OF THE IV14-ZERO VENTILATION UNIT
iV14-Zero ventilation system / sMove controller •Operating instructions
D
Operation of the iV14-Zero ventilation unit
3.1 Opening/closing the inner cover
For correct functioning of your ventilation system the ventilation unit’s inner cover must be
opened.
Close the inner cover if you take the ventilation unit out of operation.
7KLVZLOOSUHYHQWDQXQGHVLUHGDLUH[FKDQJHLHDQLQÀRZRIFROGDLULQWRWKHOLYLQJURRP
In particular situations (i. e. accidents with smoke or leaking gases) it is necessary to close all
doors and windows. In these situations your ventilation units must be disconnected from the
power supply and inner covers must be closed as well.
Re-open the inner cover before taking the ventilation unit into operation again.
Requirements: The inner cover panel is attached.
3.2 Tilting the inner cover
7RHQDEOHGLUHFWLRQRIWKHÀRZUDWHWKHSDQHORIWKH)ODLU=HURLQQHUFRYHUFDQEHWLOWHGXSZDUGV
DQGGRZQZDUGV7KHLQQHUFRYHUEHFRPHVFORVHGDWWKHWLOWHGVLGHWKHUHE\GLUHFWLQJWKHÀRZ
UDWHLQWKHRSHQGLUHFWLRQ7KHVRXQGSUHVVXUHOHYHOLVGHFUHDVHG$OVRQRWHWKDWWKHÀRZUDWH
decreases if the inner cover is only partially open.
Requirements: The inner cover is open.
ŹSlide the inner cover panel onto the lower (upper)
spacers in the direction of the base plate.
ÖYou have tilted the inner cover panel downwards
(upwards).
Ö7KHDLUÀRZZLOOQRZEHGLUHFWHGXSZDUGVGRZQ-
wards).
ÖThe sound pressure level is decreased.
EF
      G H
ŹPress the inner cover panel into the base plate in
the direction of the interior wall.
Opening the inner cover:
ŹPull the inner cover panel forwards until you feel
all four spacers snap into place.
ÖYou have opened/closed the inner cover.
1 2

12
OPERATING THE SMOVE CONTROLLERS
iV14-Zero ventilation system / sMove controller •Operating instructions
J
Operating the sMove controllers
Operating mode, output level and further functions, i. e. pause function, are adjusted via one of
the inVENTer system controllers1).
They are operated by touching the capacitive button and the slide control on the control panel.
With its integrated indicator lights, the control panel also serves as a display surface.
Flat version: :KHQLQSDXVHPRGHWKHFRQWUROOHUVZLWFKHVRႇWKHYHQWLODWLRQXQLWIRURQHKRXU
Subsequently, the ventilation unit continues to work in heat recovery mode at the lowest output
OHYHO7KHXVHRIWKHÀDWYHUVLRQLVUHFRPPHQGHGLQDUHDVZKHUHLWLVGHVLUDEOHQRWWRWXUQRႇ
WKHYHQWLODWLRQXQLWLQRUGHUWRPDLQWDLQKXPLGLW\OHYHOV6ZLWFKRႇORFN
Standard version: In addition to pause mode, the standard version provides the option to
VZLWFKRႇWKHYHQWLODWLRQXQLWFRPSOHWHO\
4.1 Design and features
Control panel
The control panel is located on the front of the control unit and also serves as a display surface.
It is composed of capacitive buttons and various indicator lights. It is operated by touching the
YDULRXVEXWWRQVPDUNHGLQJUH\LQ¿JXUH
Abbildung 2: Operating and display elements on the control panel
Slide control:
BULHÀ\SUHVVLQJWKHIDQV\PERODOORZV\RXWRVHOHFWRQHRIWKHIRXUVSHFL¿FRXWSXWOHYHOV
Touching the slide control for approx. one second lets you continuously adjust the output level by
moving it. The position of the illuminated display on the left side of the slide control indicates the
currently set output level.
;
Marker for output levels 1 – 4
2 Continuous ventilation mode
(blue) indicator light
3 Operating mode button
4 Heat recovery mode
(orange) indicator light
5 3DXVH2ႇLQGLFDWRUOLJKW
6 3DXVH2ႇEXWWRQ
7 Output level indicator lights
8 Slide control
1) The operating instructions for the MZ-Home controller are not part of this documentation. They are available separately.
1
2
3
4
5
6
7
8

13
OPERATING THE SMOVE CONTROLLERS
iV14-Zero ventilation system / sMove controller •Operating instructions
M  KL   H
Pressing again lets you switch between the heat recovery and ventilation modes. The
indicator lights to the left of the Mode button displays the currently set mode.
The output level of the ventilation unit can be adjusted in all operating modes.
O
L L  F 
G F
Symbol Flow rate (%)
1 25
2 35
3 50
4 100
3DXVH2ႇEXWWRQ
A brief press of the controller allows you to switch to the pause function. In the standard
YHUVLRQSUHVVLQJWKHEXWWRQIRUVHFRQGVDOORZV\RXWRFRPSOHWHO\VZLWFKRႇDOOYHQWLOD-
tion units connected to the controller. Pressing it again switches the connected ventilation
units back on. In)ODWYHUVLRQWKHYHQWLODWLRQXQLWFDQQRWEHVKXWRႇFRPSOHWHO\
6ZLWFKRႇORFN
Function
sMove s4 controller without connected interface
,IWKHH[WHUQDOLQWHUIDFHLVQRWFRQQHFWHGWKHPRGHDQGWKHLQWHQVLW\RIWKHDLUÀRZFDQEHVHW
on the sMove controller.
The heat recovery and continuous ventilation modes can easily be set by touching the Mode
EXWWRQ7KH2))PRGHRUWKHSDXVHIXQFWLRQFDQEHVHOHFWHGE\WRXFKLQJWKH3DXVH2ႇEXWWRQ
An indicator light next to the button indicates the selected mode.
The intensity of the ventilation can be adjusted continuously by moving the slide control, or in
four steps by touching the fan icons on the slide control. The position of the illuminated display
on the left side of the slide control indicates the currently set output level.

14
OPERATING THE SMOVE CONTROLLERS
iV14-Zero ventilation system / sMove controller •Operating instructions
sPQ RS sU VQ WXYQ Z ZS Y [\X ] VQ WWS VXS ^ \ WXS Y_ ` VS
The external interface is a bi-functional port on the back of the operating unit. It enables the
connection of a sensor with a potential-free switching contact (NOC) or the use of an analogue
input to integrate the ventilation unit into an existing home automation system.
Connecting the external interface changes the functionality of your controller as follows:
A. Interface as external switching contact
The sensor used must have a potential-free relay contact (NOC). The function settings of the
interface are adjusted via the jumper on the back of the operating unit.
7KHFRQQHFWLRQRIDSUHVVXUHPRQLWRULVQHFHVVDU\LQURRPVZLWKDLUYHQWLODWHG¿UHSODFHV
Consult a chimney sweep/construction planner about this. If the interface is used for a pressure
switch, the air pressure in the interior is measured continuously. Once the air pressure exceeds
RUIDOOVEHORZWKHVDIHW\WKUHVKROGWKHVHQVRUUHDFWVDQGWXUQVRႇDOOFRQQHFWHGYHQWLODWLRQ
units.
If the external interface is used to connect a
• CO2sensor, the CO2content in the interior is measured continuously.
• hygrostat, the relative humidity in the interior is measured continuously.
• VOC sensor, the composition of the air and the resulting air quality are measured continuously.
A CO2sensor and a hygrostat are optionally available as accessories.
Once the respective value exceeds the upper limit or falls below the lower limit, the sensor
reacts and switches all connected ventilation units to ventilation mode, output level 4.
a  
Jumper 2
setting
Upper limit exceeded/
switch activated
Lower limit exceeded/
switch deactivated
Pressure
switch
Jumper 2
attached
(closed)
Switch all ventilation units
connected to the controller
to the OFF mode.
Switch all ventilation units
connected to the controller to
the originally set mode.
CO2Sensor Jumper 2 not
attached (open)
Switch all ventilation units
connected to the controller
to continuous ventilation
mode, output level 4.
Switch all ventilation units
connected to the controller to
the originally set mode.
VOC sensor
Hygrostat
2
2
bc defg h ij k lmg
factory settings
bc defg h ij k lmg
factory settings

15
OPERATING THE SMOVE CONTROLLERS
iV14-Zero ventilation system / sMove controller •Operating instructions
no p WX S Y_` VS ` s `W `ZQ qrS \ WtrX
If the interface is used as an analogue input, the ventilation unit can be integrated into an exist-
LQJKRPHDXWRPDWLRQV\VWHP7RGRVRDSUHGH¿QHGYROWDJHOHYHOLVVHWLQWKHKRPHDXWRPDWLRQ
control unit, depending on the desired function.
TIP: It is not possible to connect a potential-free switch and an analogue input simultaneously.
A connected analogue input always has priority over a potential-free switching contact.
The jumper on the back of the operating unit must not be attached.
Depending on the control voltage, the following functions are available:
uL  
Fan voltage [V DC]
Continuous ventilation output level 4 0.00 8
v)" #" .) .& !" #$%  #)" ). w .  $ ! !$ x
0.75 8
v)" #" .) .& !" #$%  #)" ). w .  $ ! !$ y
1.75 8
v)" #" .) .& !" #$%  #)" ). w .  $ ! !$ ;
2.75 8
z{{
3.75 8
|!%  (!
5) ! (0 ) .w . $ ! !$ ;
4.75 8
|!%  (!
5) ! (0 ) .w . $ ! !$ y
5.75 8
|!%  (!
5) ! (0 ) .w . $ ! !$ x
6.75 8
|!%  (!
5) ! (0 ) .w . $ ! !$ }
7.75 8
~
Activating the controller
After activating the controller (e. g. after a power cut), the heat recovery mode will be active.
Requirements:
7KHFRQWUROOHULVVZLWFKHGRႇ
ÖYou have activated the controller.
ÖYou can switch modes and change the output
level.
If no change is made after the controller is activated, the controller will switch on the reversible
fans at the lowest output level after 60 minutes.
ŹPress the button .
ÖThe orange heat recovery indicator light is
illuminated.
Ö7KHZKLWH3DXVH2ႇLQGLFDWRUOLJKWÀDVKHV
ÖThe controller is in heat recovery mode.
Ö7KHUHYHUVLEOHIDQLVVZLWFKHGRႇ

~C
Setting mode
Setting "heat recovery" mode
In this mode the reversible fans of ventilation units in paired operation change direction at
70-second intervals. The integrated thermal accumulator charges itself with heat energy from
WKHURRPVDLUDVLWÀRZVWRWKHH[WHULRUH[WUDFWDLU:KHQWKHUHYHUVLEOHIDQFKDQJHVGLUHFWLRQ
it releases the stored heat energy into the incoming outside air (supply air). This operation is the
ventilation unit's standard operating mode.
Requirements: The controller is switched on.
ÖYou have selected "heat recovery" mode.
Setting "continuous ventilation" mode
The ventilation unit's reversible fan works without changing direction. Thus, no heat recovery
takes place in this mode. The continuous ventilation unit must be set to supply air mode.
This mode is recommended for cooling the room during summer nights. as well as for quick
extraction of stale or moist air.
Requirements: The controller is switched on.
ÖYou have selected "continuous ventilation" mode.
TIP: Pressing the button again lets you switch between the "heat recovery" and "continu-
ous ventilation" modes.
16
OPERATING THE SMOVE CONTROLLERS
iV14-Zero ventilation system / sMove controller •Operating instructions
ŹPress the button until the orange LED on
the left side of the button is illuminated:
ŹPress the button until the blue LED on the left
side of the button is illuminated:

S X X\ Wq t `r sS  Q ^S
:KHQVHWWLQJWKHSDXVHIXQFWLRQWKHFRQWUROOHUZLOO¿UVWVZLWFKRႇWKHFRQQHFWHGYHQWLODWLRQXQLWV
After 60 minutes, all ventilation units connected to the controller will restart in heat recovery
mode at 25% of the maximum output level.
Requirements:
The controller is in heat recovery or continuous
ventilation mode.
ÖYou have set the pause mode.
TIP: ,QWKHVWDQGDUGYHUVLRQZKHQWKHEXWWRQLVSUHVVHGIRUORQJHUWKDQ¿YH
VHFRQGVWKHFRQWUROOHUZLOOVZLWFKWR2))PRGH7KHLQGLFDWRUOLJKWLVSHUPDQHQWO\OLW
Setting OFF mode (only standard version)
7KHYHQWLODWLRQXQLWVIDQLVVZLWFKHGRႇZKHQWKHPRGHLVVHOHFWHG,IWKHFRQWUROOHULVVZLWFKHG
on, the controller must be activated again (page 15)
127,&(,Q)ODWYHUVLRQWKHYHQWLODWLRQXQLWFDQQRWEHVKXWR௺FRPSOHWHO\
Requirements:
The controller is in heat recovery or continuous
ventilation mode.
Ö<RXKDYHVKXWRႇWKHFRQWUROOHU
ŹPress the button .
Ö7KHZKLWH3DXVH2ႇLQGLFDWRUOLJKWÀDVKHV
ŹPress the button longer than 5 seconds.
Ö7KHZKLWH3DXVH2ႇLQGLFDWRUOLJKWLVSHUPD-
nently lit:
5 sec
1 x
17
OPERATING THE SMOVE CONTROLLERS
iV14-Zero ventilation system / sMove controller •Operating instructions

:3! ;3 8  )" 3! &$ #+! ( & $ !/  &# +! *% ( 
&  ) .w . $ ! !$ I 5 % " )" $0 , ! 53 )& !" 63!"
setting the output contiuous.
18
OPERATING THE SMOVE CONTROLLERS
iV14-Zero ventilation system / sMove controller •Operating instructions
~~
Set output
The intensity of the ventilation can be adjusted continuously by moving the slide control, or
in four steps by touching the fan icons on the slide control. The fan icons on the slide control
indicate output levels 1 (25 %), 2 (35 %), 3 (50 %) and 4 (100 %). They serve as a guide.
7KHQHZVHWWLQJWDNHVHႇHFWLPPHGLDWHO\VRWKDWDGMXVWPHQWVFDQEHPDGHSXUHO\E\OLVWHQLQJ
to changes in the sound level.
6HWWLQJWKHRXWSXWZLWKSUHGH¿QHGOHYHOV
Requirements:
The controller is in heat recovery or continuous
ventilation mode.
Ö<RXKDYHVHWWKHSUHGH¿QHGRXWSXWOHYHO
SX VQ WX\ Wr Qr s QrX tr X `^ r sXS WX
Requirements:
The controller is in heat recovery or continuous
ventilation mode.
ÖYou have set continuous output adjustment.
ŹPress the button with the symbol matching the
desired output level, e. g. level 3:
Fan output 100 % (level 4)
Fan output 50 % (level 3)
Fan output 35 % (level 2)
Fan output 25 % (level 1)
ÖThe indicator light to the left of the selected fan
icon will be illuminated.
Ź3ODFH\RXU¿QJHURQWKHVOLGHFRQWUROIRUVHFRQG
ÖThe slide control is now active.
Ź0RYH\RXU¿QJHURQWKHVOLGHFRQWUROWRWKHGHVLUHG
output level.
ÖThe indicator light to the left of the slide control
displays the output level set.
Ö
1 sec
ss
s
s
e
e
e
e
e
e
e
e
e
e
e
ee
eee
e
e
ee
e
e
e
eee
eee
e
e
e
e
e
e
e
e
e
ee
e
e
e
e
e
e
ee
e
e
e
e
e
e
e
e
ee
ee
e
e
e
e
ee
ee
e
e
e
e
e
e
ee
e
e
ee
e
c
c
cc
c
c
cc
c
c
c
c
c
c
c
cc
c
c
c
c
c
c
c
c
c
c
c
cc
c
c
cc
c
ccc
ccc
ccc
c
c
cc
cc
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
cc
c

19
OPERATING THE SMOVE CONTROLLERS
iV14-Zero ventilation system / sMove controller •Operating instructions
~
View hours run
The sMove controller comes with an integrated hours-run counter. The operating time is
displayed in days. The maximum displayable number is 4,000 days. One day corresponds to a
calculation period of 24 hours. There is no further split within these 24 hours.
The operating time is displayed as a 4-digit number.
(YHU\GLJLWEHJLQQLQJZLWKWKH¿UVWSODFHZLOOEHLQGLYLG-
ually displayed by an indicator light to the left of the slide
control/pause button .
The indicator light to the left of the button corresponds to
the number 0.
The indicator lights to the left of the slide control corre-
spond to the numbers 1 (bottom) to 9 (top).
When the number is displayed, the end value will be
permanently lit. To simplify the numbering, a number of
running lights corresponding to the end value will move
towards the end value.
The display disappears between the individual numbers.
Requirements:
The controller is switched on.
ÖYou have requested the days of operation for the
controller.
Example
LK      
Indicator light Digit
¿UVWSODFH left of the pause button 0
second place End value: 4th indicator light to the left of slide control
4 running lights move to the end value 4
third place left of the pause button 0
fourth place End value: 7th indicator light to the left of slide control
7 running lights move to the end value 7
ÖThe controller has been in operation for 0-4-0-7 days (407 days).
ŹPress the and simultaneously for 10
VHFRQGVXQWLOWKHGLVSOD\OLJKWVVZLWFKRႇ
ŹNote down the digits displayed.
ŹCombine the digits into a number:
1XPEHULQVWSODFH ¿UVWGLJLWGLVSOD\HG
Number in 2nd place = second digit displayed
Number in 3rd place = third digit displayed
Number in 4th place = fourth digit displayed
0
1
9
.
.
.
10 sec


Cleaning and maintenance
:3! # 7;} - !() !"  #$% #)" ." #& % " + 3! &  ) ! 5)" ()$ $ !( % (! #( .%$ $0 *% #" !" %" 5!-/ (!! 
Any necessary cleaning or maintenance work can be carried out by the user by following these
instructions.
TIP: Before performing cleaning or maintenance tasks, disconnect the controller's power supply
and put on gloves.
Detergents
NOTICE
The plastic/glass surface of the inner panel/controller is not scratch-resistant
and may be damaged.
• Do not use sand, soda, acid or chlorine-based cleaning agents.
A commercially available detergent in warm water can be used for cleaning. The following tools
may be used for cleaning:
• lint-free, soft cloth
• soft brush
• Vacuum cleaner
Recommended maintenance
The maintenance tasks and intervals listed here are recommended by inVENTer GmbH to
maintain the functionality and performance of the iV14-Zero ventilation system.
Depending on requirements and/or air quality, your personal maintenance plan may deviate
from these recommendations.
  G F
Assembly Maintenance activity
Cleaning from the interior room
Monthly
0LFUR¿OWHU 5HSODFHWKHPLFUR¿OWHU
3ROOHQ¿OWHU 5HSODFHWKHSROOHQ¿OWHU
Inner cover Clean the surface of the panel with a damp cloth.
sMove controller
Clean the acrylic glass cover and side surfaces
with a damp cloth.
Brush the ventilation slots free.
Quarterly 'XVW¿OWHU
:DVKWKHGXVW¿OWHUZLWKZDUPZDWHUDQG
detergent.
Or
5HSODFHGHIHFWLYHGXVW¿OWHUV
20
CLEANING AND MAINTENANCE
iV14-Zero ventilation system / sMove controller •Operating instructions