INVENTOR WF-60A1 Guide

SMART PORT WI-FI FUNCTION
AIR CONDITIONING SYSTEMS
ENGLISH | ΕΛΛΗΝΙΚΑ | ROMANA | DEUTSCH
• USER’S & INSTALLATION MANUAL
• ΕΓΧΕΙΡΙΔΙΟ ΧΡΗΣΗΣ & ΕΓΚΑΤΑΣΤΑΣΗΣ
• MANUAL DE UTILIZARE & INSTALLARE
• INSTALLATIONSHANDBUCH BENUTZERHANDBUCH

3
● This manual gives detailed description of the precautions
that should be brought to your attention during operation.
● In order to ensure correct service of the smart port,
please read this manual carefully before using the unit.
● For convenience of future reference, keep this manual
after reading it.

4
CONTENTS
1. SAFETY PRECAUTION............................................................5
2. DOWNLOAD AND INSTALL APP...........................................7
3. INSTALLATION ACCESSORY .................................................8
4. INSTALLATION METHOD......................................................9
5. SPECIFICATION....................................................................15
6. USER REGISTRATION ..........................................................16
7. NETWORK CONFIGURATION. ............................................17
8. HOW TO USE APP ...............................................................29
9. SPECIAL FUNCTIONS...........................................................31
10. APP DECLARATION ...........................................................36

5
1
Read the safety precautions carefully before installing the unit.
Stated below are important safety issues that must be obeyed.
1. SAFETY PRECAUTION
Applicable system: IOS, Android.
APP cannot support all software versions. We will not be
help responsible for any issues occuring as a result of
incompatibility.
Note:
Wireless safety strategy
Smart kit only support WPA-PSK/WPA2-PSK encryption
and none encryption . WPA-PSK/WPA2-PSK encryption
is recommended.

6
2
CAUTION
• Please Check The Service Website For More Information.
• Smart Phone camera needs to be 5 million pixels or above
to make sure scan QR code well.
• Due to different network situation, sometimes, request
time-out could happen, thus, it is necessary to do network
configuration again.
Due to different network situation, control process may
return time-out sometimes. If this situation occurs, the
display between board and App may not be the same,
please do not feel confused.
•
NOTE:Company will not be liable for any issues and
problems caused by Internet, Wi-Fi Router and Smart
Devices. Please contact the original provider to get further
help.

7
3
2. DOWNLOAD AND INSTALL APP
QR Code A QR Code B
Caution: QR Code A and
QR Code B is only available
for downloading APP.
Android Phone users: scan QR Code A or go to google play,
search 'INVmate II' app and download it.
Iphone Users: scan QR Code B or go to App Store, search
'INVmate I
I ' app and download it.

8
4
3. INSTALLATION ACCESSORY
Don‘t install at the place which is covered with heavy oil, vapor
or sulfureted gas, otherwise, this product would be deformed
that would lead to system malfunction.
Select the installation location
Preparation before installation
1.Please confirm that all the following parts have been supplied.
2. Prepare the following assemblies on the site.
The connective wires group-1
1
2
3
4
5
3
1
M4X20 (For Mounting on the Wall)
1
6
3
1
No. Name Qty. Remarks
Smart port
Installation and owner’s manual
For Mounting on the Wall
Wiring Tube(Insulating
Sleeve and Tightening
Screw)
Qty.(embeded
into wall)
Screws
Wall plugs
No. Name Remarks
Specification
(only for reference)
Smart kit
1
1
1
See Fig.4-3

9
Applicable to WF-60A1 only
5
4. INSTALLATION METHOD
Fig 4-1
Fig 4-2
1.Wifi controller structure size figure
2.Wiring Principle Sketch:
red
black
yellow
brown
red
black
yellow
brown
Insert of the
mainboard CN40
Wifi control box Indoor unit mainboard
4-Core Shield Cable, the length
is decided by installation
-----------------------------------
-----------------------------------
-----------------------------------
-----------------------------------

10
4. INSTALLATION METHOD
Fig 4-4
Connect the male joint of the connective wires group-1 to
the mainboard，then connect the other side of the
connective wires group-1 to the 4-core shielding wire of
the smart port.(See Fig.4-3)
If want to extent the wire ,please use extension cord
(purchased separately) . (See Fig.4-3)
Fig 4-3
Mainboard
4-core shielding wire
3.Wiring figure
4.Remove the upper part of the smart port
Extension cord
(purchased separately)
The connective wires group-1
CN40
Slots
Insert a slot screwdriver into the slots in the
lower part of the smart port (2 places), and
remove the upper part of the smart port.
(Fig.4-4)

11
7
Fig 4-5
4. INSTALLATION METHOD
For exposed mounting, fasten the back plate on the wall
with the 3 screws (M4×20) and plugs. (Fig.4-5)
6. .Insert the smart kit with slightly strength into the main PCB
of the smart port .(Fig.4-6)
5. Fasten the back plate of the smart port
Back plate
Screws (M4×20)
Fig 4-6

12
8
Fig 4-7
4. INSTALLATION METHOD
7. Wiring
B.Shielded wiring
Top side
wire outlet
Bottom side
wire outlet
Wiring through the wall
Wiring hole and wall hole
Diameter of wall hole:Φ20mm
A. For exposed mounting, two outletting positions.
Fig 4-8

13
9
Fig 4-9
4. INSTALLATION METHOD
CAUTION
Avoid the water enter into the smart port, use trap and putty
to seal the connectors of wires during wiring installation. (Fig.
4-9) When under installation, reserve certain length of the
connecting wire for convenient to take down the smart port
while during maintenance.
Putty Putty
Trap
Trap
8. Reattach the upper part of the smart port
After adjusting the upper case and then buckle the upper
case; avoid clamping the wiring during installation. (
Fig 4-10 )
Fig 4-10

14
10
4. INSTALLATION METHOD
NOTE:
Connection for wired control function by KJR-120C/TF-E
KJR-120G2/TFBG-E
9. Connect the smart port to the wire controller （if needed）
Fig 4-11
①Remove the top cover from the gap between the top
cover and bottom by a tool with flat head. (See Fig.4-11)
②Use the connective cable to connect the wire controller
and CN3 of the smart port. (See Fig.4-12)(refer to the Wire
controller manual for details)
Fig 4-12
CN3

15
5. SPECIFICATION
WF-60A1
IEEE802.11b/g/n
Printed PCB Antenna
Model
Standard
Antenna Type
11
Frequency
Maximum Transmitted Power
Operation Temperature
Operation Humidity
Power Input
2400~2483.5 MHz
<20dBm
0ºC~45ºC/32ºF~113ºF.
10%~85%
DC 5V/300mA
9. Connect the smart port to the wire controller （if needed）
20:14 61%
Sign up

16
6. USER REGISTRATION
Please ensure your mobile device is connected to Wifi router.
Also, the Wifi router has already connected to Internet before
doing user registration and network configuration.
It is better to log in your email box and active your registration
account by clicking link in case you forget the password.
①Click ‘Create Account’. ②Enter your email address
and password, and then
click ‘Register’.
0
Fo

17
13
7. NETWORK CONFIGURATION
CAUTION
• It is necessary to forget any other around network and
make sure the Android or IOS device just connect to the
WIFI network you want to configure.
• Make sure the Android or IOS device WIFI function works
well and can be connected back to your original WIFI
network automatically.
When AC enters into AP mode, the air-conditioning
remote controller can't control it. It is necessary to finish
network configuration or power the AC again in order to
control it. Alternatively, you need to wait 8 minutes to let
the AC quit AP mode automatically.
Kindly reminder:
•

18
14
Using Android device to do network configuration.
7. NETWORK CONFIGURATION
① Make sure your mobile device has already been connected
to the wifi network which you want to use. Also, you need
to forget other irrelative wifi network in case it influences
your cofiguration process.
② Disconnect the power supply of AC.
③ Connect the power supply of AC, and continuously press
the digital display button or do not disturb button seven
times in 3 minutes.
④When the AC displays AP , it means that the AC WIFI has
already entered into AP Mode.
Some type of AC do not need the step to be in AP mode.
•

19
14
Using Android device to do network configuration.
7. NETWORK CONFIGURATION
① Make sure your mobile device has already been connected
to the wifi network which you want to use. Also, you need
to forget other irrelative wifi network in case it influences
your cofiguration process.
② Disconnect the power supply of AC.
③ Connect the power supply of AC, and continuously press
the digital display button or do not disturb button seven
times in 3 minutes.
④When the AC displays AP , it means that the AC WIFI has
already entered into AP Mode.
Some type of AC do not need the step to be in AP mode.
•
15
7. NETWORK CONFIGURATION
⑤ Press ‘+ Add Device’
20:14
Manually Add New Device:
⑥ Select the appliance
you are setting up

20
16
⑦ Follow the above steps to enter “AP” mode.
7. NETWORK CONFIGURATION