INVENTOR M3GHP290-12 User manual

MODELS:
M3GHP290-12
M3GHP290-12BS
AIR CONDITIONING SYSTEMS
ENGLISH | ΕΛΛΗΝΙΚΑ | ROMANA
REMOTE CONTROLLER
• USER’S MANUAL
• ΕΓΧΕΙΡΙΔΙΟ ΧΡΗΣΗΣ
• MANUAL UTILIZATORULUI

4
1
5
6
7
9
10
10
10
11
11
12
15
Handling the remote controller ......................................................
Remote controller Specifications...................................................
Function buttons .................. .........................................................
Indicators on LCD ..........................................................................
How to use the buttons .................................................................
Auto operation.................................................................................
Cooling/Heating/Fan operation......................................................
Dehumidifying operation ...............................................................
Swing operation..............................................................................
Timer operation...............................................................................
ECONOMY operation ....................................................................
CONTENTS
Use the remote controller within a distance of 8
meters from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.
Location of the remote controller.
8m
CAUTIONS
The air conditioner will not operate if curtains, doors or other materials
block the signals from the remote controller to the indoor unit.
Prevent any liquid from falling into the remote controller. Do not expose
the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller, either move
these appliances or consult your local dealer.
The remote controller is powed by two dry
batteries(R03/LR03X2) housed in the rear
part and protected by a cover.
(1) Remove the cover by pressing and sliding off.
(2) Remove the old batteries and insert the new
batteries,placing the(+) and (-) ends correctly.
(3) Reattach the cover by sliding it back into
position.
NOTE: When the batteries are removed, the
remote controller erases all programming.
After inserting new batteries, the remote
controller must be reprogrammed.
Replacing batteries
.
Handling the remote controller
2
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
SWING
TIMER ON
ECONOMY
ON/OFF
TIMER OFF
RESET LOCK
SET TEMPERATURE( C)
FOLLOW
ME LED
DISPLAY
ION
TURBO

5
1
5
6
7
9
10
10
10
11
11
12
15
Handling the remote controller ......................................................
Remote controller Specifications...................................................
Function buttons .................. .........................................................
Indicators on LCD ..........................................................................
How to use the buttons .................................................................
Auto operation.................................................................................
Cooling/Heating/Fan operation......................................................
Dehumidifying operation ...............................................................
Swing operation..............................................................................
Timer operation...............................................................................
ECONOMY operation ....................................................................
CONTENTS
Use the remote controller within a distance of 8
meters from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.
Location of the remote controller.
8m
CAUTIONS
The air conditioner will not operate if curtains, doors or other materials
block the signals from the remote controller to the indoor unit.
Prevent any liquid from falling into the remote controller. Do not expose
the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller, either move
these appliances or consult your local dealer.
The remote controller is powed by two dry
batteries(R03/LR03X2) housed in the rear
part and protected by a cover.
(1) Remove the cover by pressing and sliding off.
(2) Remove the old batteries and insert the new
batteries,placing the(+) and (-) ends correctly.
(3) Reattach the cover by sliding it back into
position.
NOTE: When the batteries are removed, the
remote controller erases all programming.
After inserting new batteries, the remote
controller must be reprogrammed.
Replacing batteries
.
Handling the remote controller
2
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
SWING
TIMER ON
ECONOMY
ON/OFF
TIMER OFF
RESET LOCK
SET TEMPERATURE( C)
FOLLOW
ME LED
DISPLAY
ION
TURBO

6
Remote Controller Specifications
1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling only
model without), and FAN.
2. Timer Setting Function in 24 hours.
O O
3. Indoor Setting Temperature Range : 17 C~30 C(62 F~88 F).
4. Full function of LCD (Liquid Crystal Display)
5. Back light emitting.
Performance Feature
Function buttons
CAUTIONS
Do not mix old and new batteries or batteries of a different type.
Do not leave the batteries in the remote controller if it is not going
to be used for 2 or 3 months.
Dispose of the old batteries in the special containers to be found
in the sales outlets.
3 4
Model
Rated Voltage
-5 C 60 C( )
8m
3.0V(Dry batteries R03/LR03
RG51F/EF
2)
Environment
Signal Receiving
Range
O O
23 F~140 F
~
2
TEMP UP Button
Push this button to increase the indoor temper-
o o
ature setting in 1 C(2 F) increments to 30 C(88 F).
1
TEMP DOWN Button
Push this button to decrease the indoor temper-
o o
ature setting in 1 C(2 F) increments to 17 C(62 F).
7
SWING Button
Used to stop or start louver movement and
set the desired up/down airflow direction.
3
ON/OFF Button
Operation starts when this button is pressed
and stops when the button is pressed again.
Used to select the fan speed in four steps:
Auto Low Med High
FAN SPEED Button
4
Each time the button is pressed, the operation
modeis selected inthe sequenceof the following:
5
MODE Button
AUTO COOL
DRY HEAT FAN
NOTE Please do not select HEAT mode if
the machine you purchased is cooling only
type. Heat mode is not supported by the
cooling only appliance.
in 30 minutes increments, up to 10 hours, then at
1 hour increments up to 24 hours. To cancel the
Auto-on time setting, just press the button until
the time setting is 0.0.
6
TIMER ON Button
Press this button to activate the Auto-on time
setting. Each press will increase the time setting
ECONOMY/SLEEP Button
NOTE: While the unit is running under ECONOMY/
SLEEP mode, it would be cancelled if press MODE,
FAN SPEED or ON/OFF button.
Select this function during the sleeping time. It
can maintain the most comfortable temperature
and save energy. This function is available on
COOL, HEAT orAUTO mode only .
8
Model: RG51F/EF
SHORT CUT
I SENSE
1
3
5
7
9
11
2
4
6
8
10
12

7
Remote Controller Specifications
1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling only
model without), and FAN.
2. Timer Setting Function in 24 hours.
O O
3. Indoor Setting Temperature Range : 17 C~30 C(62 F~88 F).
4. Full function of LCD (Liquid Crystal Display)
5. Back light emitting.
Performance Feature
Function buttons
CAUTIONS
Do not mix old and new batteries or batteries of a different type.
Do not leave the batteries in the remote controller if it is not going
to be used for 2 or 3 months.
Dispose of the old batteries in the special containers to be found
in the sales outlets.
3 4
Model
Rated Voltage
-5 C 60 C( )
8m
3.0V(Dry batteries R03/LR03
RG51F/EF
2)
Environment
Signal Receiving
Range
O O
23 F~140 F
~
2
TEMP UP Button
Push this button to increase the indoor temper-
o o
ature setting in 1 C(2 F) increments to 30 C(88 F).
1
TEMP DOWN Button
Push this button to decrease the indoor temper-
o o
ature setting in 1 C(2 F) increments to 17 C(62 F).
7
SWING Button
Used to stop or start louver movement and
set the desired up/down airflow direction.
3
ON/OFF Button
Operation starts when this button is pressed
and stops when the button is pressed again.
Used to select the fan speed in four steps:
Auto Low Med High
FAN SPEED Button
4
Each time the button is pressed, the operation
modeis selected inthe sequenceof the following:
5
MODE Button
AUTO COOL
DRY HEAT FAN
NOTE Please do not select HEAT mode if
the machine you purchased is cooling only
type. Heat mode is not supported by the
cooling only appliance.
in 30 minutes increments, up to 10 hours, then at
1 hour increments up to 24 hours. To cancel the
Auto-on time setting, just press the button until
the time setting is 0.0.
6
TIMER ON Button
Press this button to activate the Auto-on time
setting. Each press will increase the time setting
ECONOMY/SLEEP Button
NOTE: While the unit is running under ECONOMY/
SLEEP mode, it would be cancelled if press MODE,
FAN SPEED or ON/OFF button.
Select this function during the sleeping time. It
can maintain the most comfortable temperature
and save energy. This function is available on
COOL, HEAT orAUTO mode only .
8
Model: RG51F/EF
SHORT CUT
I SENSE
1
3
5
7
9
11
2
4
6
8
10
12

8
Function buttons(continued)
5 6
Remote Screen Indicators
Push this button to set and activate your favorite
pre-settings.
9
SHORT CUT Button:
11
I SENSE Button
Temperature sensing and room temperature
display button.
TIMER OFF Button
10
Press this button to activate the Auto-off time
setting. Each press will increase the time setting
in 30 minutes increments, up to 10 hours, then at
1 hour increments up to 24 hours. To cancel the
Auto-off time setting, just press the button until
the time setting is 0.0.
12
Press this button to clear the display on the
indoor unit, press it again to light the
display.
LED Display Button
Press together the two buttons
simultaneously (SHORT CUT & TIMER
OFF buttons) for 5 seconds to lock the
keyboard. Press together the two buttons
again for 2 seconds to unlock the keyboard.
Press together simultaneously
Model: RG51F/EF
SHORT CUT
I SENSE
1
3
5
7
9
11
2
4
6
8
10
12
Information are displayed when the remote controller is power up.
Note:
All indicators shown in the figure are for the
purpose of clear presentation. But during the
actaul operation, only the relative function signs
are shown on the display window.
Displayed when data transmitted.
Displayed when remote controller is ON.
Low speed
NO display
Medium speed(some units)
High speed
Auto fan speed
Displayed when TIMER ON time is set
Displayed when TIMER OFF time is set
Indicated all the current settings are
locked
Shows set temperature or room
temperature, or time under TIMER setting
HIGH
MED
LOW
AUTO
COOL
DRY
HEAT
AUTO
HEAT
COOL
FAN
DRY
Mode display
Fan speed indication
FAN
HIGH
MED
LOW
Displayed when I SENSE feature is
activated(some units)
Displayed when SLEEP feature is activated
(some units)

9
Function buttons(continued)
5 6
Remote Screen Indicators
Push this button to set and activate your favorite
pre-settings.
9
SHORT CUT Button:
11
I SENSE Button
Temperature sensing and room temperature
display button.
TIMER OFF Button
10
Press this button to activate the Auto-off time
setting. Each press will increase the time setting
in 30 minutes increments, up to 10 hours, then at
1 hour increments up to 24 hours. To cancel the
Auto-off time setting, just press the button until
the time setting is 0.0.
12
Press this button to clear the display on the
indoor unit, press it again to light the
display.
LED Display Button
Press together the two buttons
simultaneously (SHORT CUT & TIMER
OFF buttons) for 5 seconds to lock the
keyboard. Press together the two buttons
again for 2 seconds to unlock the keyboard.
Press together simultaneously
Model: RG51F/EF
SHORT CUT
I SENSE
1
3
5
7
9
11
2
4
6
8
10
12
Information are displayed when the remote controller is power up.
Note:
All indicators shown in the figure are for the
purpose of clear presentation. But during the
actaul operation, only the relative function signs
are shown on the display window.
Displayed when data transmitted.
Displayed when remote controller is ON.
Low speed
NO display
Medium speed(some units)
High speed
Auto fan speed
Displayed when TIMER ON time is set
Displayed when TIMER OFF time is set
Indicated all the current settings are
locked
Shows set temperature or room
temperature, or time under TIMER setting
HIGH
MED
LOW
AUTO
COOL
DRY
HEAT
AUTO
HEAT
COOL
FAN
DRY
Mode display
Fan speed indication
FAN
HIGH
MED
LOW
Displayed when I SENSE feature is
activated(some units)
Displayed when SLEEP feature is activated
(some units)

10
7 8
Cooling /Heating/Fan operation
Ensure the unit is plugged in and power is
available.
1. Press the MODE button to select COOL, HEAT,
(cooling & heating models only) or FAN mode.
2. Press the TEMP button to set the desired
temperature. The temperature can be set
within a range of
3. Press the FAN SPEEDbutton to select the
fan speed in four steps- Auto, Low, Med,or High.
4. Press the ON/OFF button to start the air
conditioner.
17 C(62 F)~ 30 C in 1 C(2 F)
increments.
In the FAN mode, the setting temperature is not
displayed in the remote controller and you are not
able to control the room temperature either. In this
case, only step 1, 3 and 4 may be performed.
NOTE
Dehumidifying operation
Ensure the unit is plugged in and power is
available. The OPERATION indicator on the
display panel of the indoor unit illuminates.
1. Press the MODE button to select DRY mode.
2. Press the TEMP button to set the desired
temperature. The temperature can be set
within a range of
increments.
3. Press the ON/OFF button to start the air
conditioner.
17 C(62 F)~ 30 C in 1 C(2 F)
In the Dehumidifying mode, you can not switch
the fan speed. It has already been automatically
controlled.
NOTE
How to use the buttons
Auto operation
Ensure the unit is plugged in and power is
available. The OPERATION indicator on the
display panel of the indoor unit illuminates.
1. Press the MODE button to select Auto.
2. Press the TEMP button to set the desired
temperature. The temperature can be set
within a range of 17 C(62 F)~ 30 C in 1 C(2 F)
increments.
3. Press the ON/OFFbutton to start the air
conditioner.
1. In the Auto mode, the air conditioner can logically
choose the mode of Cooling, Fan, Heating and
Dehumidifying by sensing the difference between the
actual ambient room temperature and the set temper-
ature on the remote controller.
2. In the Auto mode, you can not switch the fan speed.
It has already been automatically controlled.
3. If the Auto mode is not comfortable for you , the
desired mode can be selected manually.
NOTE
Swing operation
Use the SWING button to adjust the Up/Down
airflow direction.
1. When press the button once and quickly, the
air flow direction setting feature of the louver is
activated. The moving angle of the louver is
o
6 for each press. Keep pressing the button to
move the louver to the desired position.
2. If keep pressing the SWING button without
releasing for 2 more seconds, the auto swing
feature of the louver is activated. The horizontal
louver would swing up/down automatically.
Press it again to stop.
NOTE: When the louver swing or move to a
position which would affect the cooling
and heating effect of the air conditioner,
it would automatically change the swing/
moving direction.
3
1
2
SHORT CUT
I SENSE
3
1
2
SHORT CUT
I SENSE
1
SHORT CUT
I SENSE
4
1
2
3
SHORT CUT
I SENSE
4
1
2
3
SHORT CUT
I SENSE

11
7 8
Cooling /Heating/Fan operation
Ensure the unit is plugged in and power is
available.
1. Press the MODE button to select COOL, HEAT,
(cooling & heating models only) or FAN mode.
2. Press the TEMP button to set the desired
temperature. The temperature can be set
within a range of
3. Press the FAN SPEEDbutton to select the
fan speed in four steps- Auto, Low, Med,or High.
4. Press the ON/OFF button to start the air
conditioner.
17 C(62 F)~ 30 C in 1 C(2 F)
increments.
In the FAN mode, the setting temperature is not
displayed in the remote controller and you are not
able to control the room temperature either. In this
case, only step 1, 3 and 4 may be performed.
NOTE
Dehumidifying operation
Ensure the unit is plugged in and power is
available. The OPERATION indicator on the
display panel of the indoor unit illuminates.
1. Press the MODE button to select DRY mode.
2. Press the TEMP button to set the desired
temperature. The temperature can be set
within a range of
increments.
3. Press the ON/OFF button to start the air
conditioner.
17 C(62 F)~ 30 C in 1 C(2 F)
In the Dehumidifying mode, you can not switch
the fan speed. It has already been automatically
controlled.
NOTE
How to use the buttons
Auto operation
Ensure the unit is plugged in and power is
available. The OPERATION indicator on the
display panel of the indoor unit illuminates.
1. Press the MODE button to select Auto.
2. Press the TEMP button to set the desired
temperature. The temperature can be set
within a range of 17 C(62 F)~ 30 C in 1 C(2 F)
increments.
3. Press the ON/OFFbutton to start the air
conditioner.
1. In the Auto mode, the air conditioner can logically
choose the mode of Cooling, Fan, Heating and
Dehumidifying by sensing the difference between the
actual ambient room temperature and the set temper-
ature on the remote controller.
2. In the Auto mode, you can not switch the fan speed.
It has already been automatically controlled.
3. If the Auto mode is not comfortable for you , the
desired mode can be selected manually.
NOTE
Swing operation
Use the SWING button to adjust the Up/Down
airflow direction.
1. When press the button once and quickly, the
air flow direction setting feature of the louver is
activated. The moving angle of the louver is
o
6 for each press. Keep pressing the button to
move the louver to the desired position.
2. If keep pressing the SWING button without
releasing for 2 more seconds, the auto swing
feature of the louver is activated. The horizontal
louver would swing up/down automatically.
Press it again to stop.
NOTE: When the louver swing or move to a
position which would affect the cooling
and heating effect of the air conditioner,
it would automatically change the swing/
moving direction.
3
1
2
SHORT CUT
I SENSE
3
1
2
SHORT CUT
I SENSE
1
SHORT CUT
I SENSE
4
1
2
3
SHORT CUT
I SENSE
4
1
2
3
SHORT CUT
I SENSE

12
910
Timer operation
press the TIMER ON button can set the auto-on
time of the unit. And press the TIMER OFF button
can set the auto-off time of the unit.
1. Press the TIMER ON button. The remote
controller shows TIMER ON, the last Auto-on
setting time and the signal "h" will be shown on
the LCD display area. Now it is ready to reset the
Auto-on time to START the operation.
2. Push the TIMER ON button again to set desired
Auto-on time. Each time you press the buttons,
the time increases in 30 minutes increments, up
to 10 hours, then at 1 hour increments up to 24
hours.
3. After setting the TIMER ON ,there will be a one
second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "h" will disappear and the set temperature
will re-appear on the LCD display window.
To set the Auto-on time.
To set the Auto-off time.
1. Press the TIMER OFF button. The remote
controller shows TIMER OFF, the last Auto-off
setting time and the signal "h" will be shown on
the LCD display area. Now it is ready to
reset the Auto-off time to START the operation.
2. Push the TIMER OFF button again to set desired
Auto-off time. Each time you press the TEMP. UP
or TEMP. DOWN buttons the time increases in
30 minutes increments, upto 10 hours, then at
1 hour increments up to 24 hours.
3. After setting the TIMER OFF ,there will be a one
second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "h" will disappear and the set temperature
will re-appear on the LCD display window.
The effective operation time set by the remote controller for the timer
function is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0,
3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13,
14, 15,16,17, 18, 19, 20, 21, 22, 23 and 24.
IMPORTANT
Example of Timer setting
TIMER ON
Start
Off
6 hours later
(Auto-on Operation)
The TIMER ON feature is useful when you want
the unit to turn on automatically before you return
home. The air conditioner will automatically start
operating at the set time.
To start the air conditioner in 6 hours.
1. Press the TIMER ON button, the last setting of
starting operation time and the signal "h" will
show on the display area.
2. Press the TIMER ON button to display "6:0h" on
the TIMER ON display of the remote controller.
3. Wait for about 3 seconds and the digital display
area will show the temperature again. Now this
function is activated.
TIMER ON
Example:
h
Set
Note: Cancel either function by setting its timer to 0.0h.
1
2
SHORT CUT
I SENSE

13
910
Timer operation
press the TIMER ON button can set the auto-on
time of the unit. And press the TIMER OFF button
can set the auto-off time of the unit.
1. Press the TIMER ON button. The remote
controller shows TIMER ON, the last Auto-on
setting time and the signal "h" will be shown on
the LCD display area. Now it is ready to reset the
Auto-on time to START the operation.
2. Push the TIMER ON button again to set desired
Auto-on time. Each time you press the buttons,
the time increases in 30 minutes increments, up
to 10 hours, then at 1 hour increments up to 24
hours.
3. After setting the TIMER ON ,there will be a one
second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "h" will disappear and the set temperature
will re-appear on the LCD display window.
To set the Auto-on time.
To set the Auto-off time.
1. Press the TIMER OFF button. The remote
controller shows TIMER OFF, the last Auto-off
setting time and the signal "h" will be shown on
the LCD display area. Now it is ready to
reset the Auto-off time to START the operation.
2. Push the TIMER OFF button again to set desired
Auto-off time. Each time you press the TEMP. UP
or TEMP. DOWN buttons the time increases in
30 minutes increments, upto 10 hours, then at
1 hour increments up to 24 hours.
3. After setting the TIMER OFF ,there will be a one
second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "h" will disappear and the set temperature
will re-appear on the LCD display window.
The effective operation time set by the remote controller for the timer
function is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0,
3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13,
14, 15,16,17, 18, 19, 20, 21, 22, 23 and 24.
IMPORTANT
Example of Timer setting
TIMER ON
Start
Off
6 hours later
(Auto-on Operation)
The TIMER ON feature is useful when you want
the unit to turn on automatically before you return
home. The air conditioner will automatically start
operating at the set time.
To start the air conditioner in 6 hours.
1. Press the TIMER ON button, the last setting of
starting operation time and the signal "h" will
show on the display area.
2. Press the TIMER ON button to display "6:0h" on
the TIMER ON display of the remote controller.
3. Wait for about 3 seconds and the digital display
area will show the temperature again. Now this
function is activated.
TIMER ON
Example:
h
Set
Note: Cancel either function by setting its timer to 0.0h.
1
2
SHORT CUT
I SENSE

14
11 12
TIMER OFF
Stop
On
Set 10 hours later
(Auto-off Operation)
The TIMER OFF feature is useful when you want
the unit to turn off automatically after you go to bed.
The air conditioner will stop automatically at the set
time.
To stop the air conditioner in 10 hours.
1. Press the TIMER OFF button, the last setting of
stopping operation time and the signal "h" will
show on the display area.
2. Press the TIMER OFF button to display "10h" on
the TIMER OFF display of the remote controller.
3. Wait for about 3 seconds and the digital display
area will show the temperature again. Now this
function is activated.
TIMER OFF
Example:
h
TIMER ON OFF
h
On Stop
2 hours later
after setting
Set
To stop the air conditioner 2 hours after setting
and start it again 10 hours after setting.
1. Press the TIMER OFF button.
2. Press the TIMER OFF button again to
display 2.0h on the TIMER OFF display.
3. Press the TIMER ON button.
4. Press the TIMER ON button again to
display 10h on the TIMER ON display .
5. Wait for the remote control to display
the setting temperature.
TIMER OFF TIMER ON
(On Stop Start operation)
This feature is useful when you want to stop the air
conditioner after you go to bed, and start it again in
the morning when you wake up or when you return
home.
Example:
COMBINED TIMER
(Setting both ON and OFF timers simultaneously)
Start
10 hours later
after setting
Example:
TIMER ON TIMER OFF
(Off Start Stop operation)
This feature is useful when you want to start
the air conditioner before you wake up and
stop it after you leave the house.
To start the air conditioner 2 hours after
setting, and stop it 5 hours after setting.
1. Press the TIMER ON button.
2. Press the TIMER ON button again to
display 2.0h on the TIMER ON display.
3. Press the TIMER OFF button.
4. Press the TIMER OFF button again to
display 5.0h on the TIMER OFF display .
5. Wait for the remote control to display
the setting temperature.
Off Stop
Start
TIMER ON OFF
h
2 hours later
after setting 5 hours later
after setting
Set
The timer setting(TIMER ON or TIMER OFF) that in
sequence occurs directly after the set time will be
activated first.
CAUTION
!
ECONOMY(SLEEP) operation
When you press the ECONOMY button, the
economic running function will be activated,
the set temperature will increase(cooling) or
o o
decrease(heating) by 1 C(2 F) over the next
o o
30 minutes and by another 1 C(2 F) after an
additional 30 minutes.This new temperature
will be maintained for 7 hours before it returns
to the originally selected temperature.(NOTE:
On some models, the set temperature will
increase (cooling) or decrease(heating) by
o o
1 C(2 F) per hour for 2 hours. This new
temperature will be maintained for 5 hours ,
then the unit is off.)
NOTE: The ECONOMY/SLEEP function is only
available under Cooling, Heating and
AUTO operation.
1
SHORT CUT
I SENSE

15
11 12
TIMER OFF
Stop
On
Set 10 hours later
(Auto-off Operation)
The TIMER OFF feature is useful when you want
the unit to turn off automatically after you go to bed.
The air conditioner will stop automatically at the set
time.
To stop the air conditioner in 10 hours.
1. Press the TIMER OFF button, the last setting of
stopping operation time and the signal "h" will
show on the display area.
2. Press the TIMER OFF button to display "10h" on
the TIMER OFF display of the remote controller.
3. Wait for about 3 seconds and the digital display
area will show the temperature again. Now this
function is activated.
TIMER OFF
Example:
h
TIMER ON OFF
h
On Stop
2 hours later
after setting
Set
To stop the air conditioner 2 hours after setting
and start it again 10 hours after setting.
1. Press the TIMER OFF button.
2. Press the TIMER OFF button again to
display 2.0h on the TIMER OFF display.
3. Press the TIMER ON button.
4. Press the TIMER ON button again to
display 10h on the TIMER ON display .
5. Wait for the remote control to display
the setting temperature.
TIMER OFF TIMER ON
(On Stop Start operation)
This feature is useful when you want to stop the air
conditioner after you go to bed, and start it again in
the morning when you wake up or when you return
home.
Example:
COMBINED TIMER
(Setting both ON and OFF timers simultaneously)
Start
10 hours later
after setting
Example:
TIMER ON TIMER OFF
(Off Start Stop operation)
This feature is useful when you want to start
the air conditioner before you wake up and
stop it after you leave the house.
To start the air conditioner 2 hours after
setting, and stop it 5 hours after setting.
1. Press the TIMER ON button.
2. Press the TIMER ON button again to
display 2.0h on the TIMER ON display.
3. Press the TIMER OFF button.
4. Press the TIMER OFF button again to
display 5.0h on the TIMER OFF display .
5. Wait for the remote control to display
the setting temperature.
Off Stop
Start
TIMER ON OFF
h
2 hours later
after setting 5 hours later
after setting
Set
The timer setting(TIMER ON or TIMER OFF) that in
sequence occurs directly after the set time will be
activated first.
CAUTION
!
ECONOMY(SLEEP) operation
When you press the ECONOMY button, the
economic running function will be activated,
the set temperature will increase(cooling) or
o o
decrease(heating) by 1 C(2 F) over the next
o o
30 minutes and by another 1 C(2 F) after an
additional 30 minutes.This new temperature
will be maintained for 7 hours before it returns
to the originally selected temperature.(NOTE:
On some models, the set temperature will
increase (cooling) or decrease(heating) by
o o
1 C(2 F) per hour for 2 hours. This new
temperature will be maintained for 5 hours ,
then the unit is off.)
NOTE: The ECONOMY/SLEEP function is only
available under Cooling, Heating and
AUTO operation.
1
SHORT CUT
I SENSE

16
I SENSE operation:
The I SENSE operation enables the remote control to
measure the temperature at its current location and
send this signal to the air conditioner every 3 minutes
interval.
NOTE: Press this button for seven seconds to start/
stop memory feature of I SENSE function.
If the memory feature is activated, “ON” will display for
3 seconds on the screen.
If the memory feature is stopped, “OF” will display for 3
seconds on the screen.
While the memory feature is activated, press the ON/
OFF button, shift the mode or power failure will not
cancel the I SENSE function.
SHORT CUT operation:
This button is used to restore the current settings or
resume previous settings.
Push this button when remote controller is on, and the
system will automatically revert back to the previous
settings including operating mode, setting temperature,
fan speed level and sleep feature (if activated).
If pushing more than 2 seconds, the system will auto-
matically restore the current operation settings includ-
ing operating mode, setting temperature, fan speed
level and sleep feature (if activated).
SHORT CUT
I SENSE

17
13
NOTE:
-Buttons design is based on typical model and might be slightly different
from the actual one you purchased, the actual shape shall prevail.
-All the functions described are accomplished by the unit, if the unit has
no this feature, there is no corresponding operation happened when
press the relative button on the remote controller.
-When there are wide differences between Remote controller Illustration
and USERS MANUALon function description, the description on USERS
MANUAL shall prevail.
-The device could comply with the local national regulations. In Canada,
it should comply with CAN ICES-3(B)/NMB-3(B). In USA, this device
complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interfe-
rence, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
-This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for
compliance could void suers authority to operate the equipment.
All the pictures in the manual are for explanatory purposes only. The actual shape of the
unit you purchased may be slightly dierent, but the operations and functions are the
same.
The company may not be held responsible for any misprinted information. The design
and the specications of the product for reasons, such as product improvement, are
subject to change without any prior notice.
Please consult with the manufacturer at [phone] or with the Sales agency for
further details. Any future updates to the manual will be uploaded to the service website,
and it is advised to always check for the latest version.
Scan here to download the latest version of this manual.
www.inventorairconditioner.com/media-library

18
1
ΠΕΡΙΕΧΟΜΕΝΑ
Χειρισµός του τηλεχειριστηρίου............................................................2
Προδιαγραφές του τηλεχειριστηρίου....................................................3
Λειτουργίες των πλήκτρων....................................................................4
Ενδείξεις στην οθόνη LCD.....................................................................6
Η χρήση των πλήκτρων.........................................................................7
Αυτόµατη λειτουργία.............................................................................7
Ψύξη/Θέρµανση/ Λειτουργία ανεµιστήρα.............................................7
Λειτουργία αφύγρανσης........................................................................8
Λειτουργία κίνησης των περσίδων........................................................8
Λειτουργία χρονοδιακόπτη....................................................................9
Λειτουργία ECO....................................................................................12
Χειρισµός του τηλεχειριστηρίου .........................................................................19
Προδιαγραφές του τηλεχειριστηρίου. ................................................................20
Λειτουργίες των πλήκτρων. ................................................................................21
Ενδείξεις στην οθόνη LCD ...................................................................................23
Η χρήση των πλήκτρων ......................................................................................24
Αυτόµατη λειτουργία ...........................................................................................24
Ψύξη/Θέρµανση/ Λειτουργία ανεµιστήρα. .........................................................24
Λειτουργία αφύγρανσης .....................................................................................25
Λειτουργία κίνησης των περσίδων .....................................................................25
Λειτουργία χρονοδιακόπτη .................................................................................26
Λειτουργία ECO ...................................................................................................29

19
2
Χειρισµός του τηλεχειριστηρίου
Η θέση του τηλεχειριστηρίου.
Χρησιµοποιήστε το τηλεχειριστήριο σε απόσταση εντός 8
µέτρων από τη συσκευή, κατευθύνοντας το προς το δέκτη
της συσκευής.
Η λήψη εντολής επιβεβαιώνεται µε ηχήτική ειδοποίηση.
!ΠΡΟΣΟΧΗ
• Το κλιµατιστικό δεν θα λειτουργήσει εάν το σήµα από το
τηλεχειριστήριο µπλοκάρεται από κουρτίνες, πόρτες και άλλα υλικά.
• Αποτρέψτε τη ρίψη υγρών στο τηλεχειριστήριο. Μην αφήνετε
εκτεθειµένο το τηλεχειριστήριο στον ήλιο ή σε θερµότητα.
• Εάν ο δέκτης του κλιµατιστικού είναι εκτεθειµένος στον ήλιο είναι
πιθανόν οι εντολές από το τηλεχειριστήριο να είναι λανθασµένες και το
κλιµατιστικό να µην λειτουργήσει σωστά. Χρησιµοποιήστε κουρτίνες ή
άλλα σκίαστρα για να αποτρέψετε την έκθεση στον ήλιο.
• Εάν ανταποκρίνονται και άλλες συσκευές στο τηλεχειριστήριο,
µετακινήστε αυτές τις συσκευές ή συµβουλευτείτε τον προµηθευτή σας.
Αντικατάσταση των µπαταριών
Το τηλεχειριστήριο τροφοδοτείται από δύο
µπαταρίες οι οποίες τοποθετούνται στο πίσω
µέρος και προστατεύονται από κάλυµµα.
(1) Αφαιρέστε το κάλυµµα πιέζοντας και
σερνοντάς το προς τα έξω.
(2) Αφαιρέστε τις παλιές µπαταρίες και
τοποθετείστε τις νέες, τοποθετώντας τους
πώλους (+) και (-) σωστά.
(3) Επανατοποθετείστε το κάλυµµα στη θέση του.
ΣΗΜΕΙΩΣΗ: Όταν αφαιρούνται οι µπαταρίες,
υπάρχουσες ρυθµίσεις σβήνουν από την µνήµη
του τηλεχειριστηρίου. Όταν τοποθετήσετε τις
νέες µπαταρίες το τηλεχειριστήριο πρέπει να
επαναπρογραµµατιστεί.
8m
.
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
SWING
TIMER ON
ECONOMY
ON/OFF
TIMER OFF
RESET LOCK
SET TEMPERATURE( C)
FOLLOW
ME LED
DISPLAY
ION
TURBO

20
3
!ΠΡΟΣΟΧΗ
• Μην χρησηµοποιείτε νέες µπαταρίες µαζί µε παλιές ή µε µπαταρίες
άλλου τύπου.
Μην αφήνετε τις µπαταρίες στο τηλεχειριστήριο εάν δεν πρόκειται να το
χρησιµοποιήσετε για 2-3 µήνες.
• Απορρίψτε τις παλίες µπαταρίες στους ειδικούς κάδους που βρίσκονται
στα περισσότερα καταστήµατα ηλεκτρικών ειδών.
Χαρακτηριστικά λειτουργιών
1. Τρόπος λειτουργίας: Αυτόµατη λειτουργία, ψύξη, αφύγρανση, θέρµανση
και λειτουργία ανεµιστήρα.
2. Ρύθµιση χρονοδιακόπτη (επιλογή 24h)
3. Εύρος ρύθµισης εσωτερικής θερµοκρασίας : 17°C 30°C.
4. Λειτουργία της οθόνης υγρών κρυστάλων (LCD)
ΣΗΜΕΙΩΣΗ:
Όλες οι εικονογραφήσεις σε αυτό το εγχειρίδιο είναι για επεξηγηµατικούς
σκοπούς µόνο. Το κλιµατιστικό σας µπορεί να διαφέρει ελαφρώς.
Το πραγµατικό σχήµα θα επικρατήσει.
Προδιαγραφές του τηλεχειριστηρίου
ΜΟΝΤΕΛΟ
Ονοµαστική τάση 3.0V (Ξηρού τυπού µπαταρίες R03/L03X2)
RG51F/EF
Εύρος λήψης
σήµατος 8m
Περιβάλλον
λειτουργίας -5°C ~ 60°C ( -41ºF ~ 140ºF )
4
7. SWING Πλήκτρο
Χρησιµοποιείται να σταµατάει ή να εκκινεί την κίνηση της
περσίδας και θα θέτει την επιθυµητή κατεύθυνση του αέρα.
1. Πλήκτρο Temp UP
Πιέστε αυτό το πλήκτρο για να αυξήσετε τη θερµοκρασία
κατά 1°C έως τους 30°C.
2. Πλήκτρο Temp DOWN
Πιέστε αυτό το πλήκτρο για να µειώσετε τη θερµοκρασία
κατά 1°C έως τους 17°C.
3. Πλήκτρο ON/OFF
Όταν πιέσετε αυτό το πλήκτρο ενεργοποιείται ή
απενεργοποιείται το κλιµατιστικό.
ΣΗΜΕΙΩΣΗ: Η θέρµανση είναι διαθέσιµη µόνο σε µονάδες
που υποστηρίζουν θέρµανση και ψύξη.
5. Πλήκτρο MODE
Κάθε φορά που πιέζετε το πλήκτρο αυτό αλλάζει ο τρόπος
λειτουργίας µε την ακόλουθη σειρά:
→ Aυτόµατη → Ψύξη → Αφύγρανση → Θέρµανση → Ανεµιστήρας -
4. Πλήκτρο FAN SPEED
Πιέζοντας το πλήκτρο αυτό επιλέγετε την ταχύτητα του ανε
µιστήρα µε την ακόλουθη σειρά:
→ Aυτόµατη → Χαµηλή → Μεσαία → Υψηλή -
6. Πλήκτρο TIMER ON
Πιέστε το πλήκτρο αυτό για την αυτόµατη ενεργοποίηση της
συσκευής µε τον χρονοδιακόπτη. Κάθε πάτηµα του πλήκτρου
αυξάνει το χρόνο κατά 30 λεπτά, έως τις 10 ώρες, και κατά 1
ώρα έως τις 24 ώρες. Για την ακύρωση της ρύθµισης,
κρατήστε πατηµένο το πλήκτρο ώσπου να ανάψει στην οθόνη
το 0.0.
8. ECONOMY (SLEEP) Πλήκτρο
Επιλέξτε τη ρύθµιση αυτή κατά την διάρκεια του ύπνου.
Μπορεί να διατηρήσει την θεµιτή θερµοκρασία και να εξοικονο-
µήσει ενέργεια. Η λειτουργία αυτή έιναι διαθέσιµη µόνο στις
ρυθµίσεις ψύξης, θέρµανσης και αυτόµατη λειτουργία.
ΣΗΜΕΙΩΣΗ: Όταν η συσκευή λειτουργεί στη λειτουργία
εξοικονόµησης ενέργειας, θα ακυρωθεί εάν πιέσετε πλήκτρο
ρύθµισης FAN SPEED ή το πλήκτρο ON/OFF.
Model: RG51F/EF
SHORT CUT
I SENSE
1
3
5
7
9
11
2
4
6
8
10
12