IOGear GUW101A User manual

1
GUW101A
Installation
Installation Guide
Wireless Audio Receiver

2
3

2
3
Table of Contents
System Requirements 4
Package Contents 5
Device Overview - Wireless Audio Receiver 6
Software Installation - Preparing for Setup 7
Software Installation – For XP users 8
Update/Install Wireless USB Manager 8
Update USB Transmitter 11
Update Wireless VGA Receiver 15
Software Installation – For Vista users 20
Update/Install Wireless USB Manager 20
Update USB Transmitter 23
Update Wireless Video Receiver 28
Hardware Installation 34
Connecting the Audio Receiver to Speakers 38
Advanced Settings – Wireless USB Manager 42
Advanced Settings – Wireless USB
Transmitter Setting
44
Trouble Shooting Guide 46
Technical Specication 60
Appendix 62
Limited Warranty 66
Federal Communications Commission
(FCC) Statement
67
Contact 68

4
5
System Requirements
1 x Wireless USB Transmitter (GUWA200)•
Available 3.5mm or RCA audio input socket on your TV/display or stereo system•
Important Note: Your computer must be Wireless USB ready or has already installed Wireless USB on the
computer before you can use the Wireless Audio Receiver.

4
5
1 x Power adapter•
1 x Quick Start Guide /•
User manual
1 x Installation CD•
1 x Warranty /•
Registration Card
Package Contents
1 x Wireless USB to•
Audio receiver (for stereo)
1 x USB 2.0 A to mini-B cable (3 ft.)•
1 x 3.5mm to 3.5mm cable•
1 x 3.5mm to RCA cable•

6
7
Device Overview - Wireless Audio Receiver
Power/Activity LED1.
- LED is solid when connection is established
- LED is blinking when power is on and con
nection is not established
3.5mm Audio Socket2.
- Connects to the 3.5mm audio connector of
the included 3.5mm or RCA audio cable, and
the other end to the available 3.5mm audio
socket or RCA audio socket on your display
or stereo system
Mini-B USB Port3.
- Connects to the mini-B end of the included
USB cable, and the Type-A end to an avail
able USB port on your computer to create
association between your computer and the
audio receiver
Power plug4.
- Power adapter socket
1
2
3
4

6
7
Software Installation - Preparing for Setup
This section is only for customers who previously purchased GUW2015VKIT, GUW2015VKITW6 or
GUW2015V. In order to ensure the quality of the performance, this section will guide you through
a series of steps for upgrading the Wireless USB Manager software and the rmware of the USB
Transmitter and the Wireless Video Receiver. Please follow the exact procedures, DO NOT skip or
re-arrange the procedures.
If this is your rst purchase of Wireless USB products and you do not have any GUW2015VKIT,
GUW2015VKITW6 or GUW2015V, then please follow below instructions to complete only the
Update/Install Wireless USB Manager section. Then proceed to page 34 for Hardware Instal-
lation.

8
9
Update/Install Wireless USB Manager
Insert the CD into the CD-ROM of your1.
computer, and the auto run program will load
the GUW101A Software Installation window.
Click on2. Install Wireless USB Manager to
continue
Click on3. Yes to continue.
Software Installation – For XP users

8
9
Click on4. Next to continue.

10
11
Select5. Yes, I want to restart my computer
now., then click on Finish to restart your
computer.

10
11
Update USB Transmitter
Before you begin, keep the USB Transmitter1.
plugged into the USB port of your computer.
DO NOT unplug the USB Transmitter from
the USB port, and DO NOT remove the USB
Transmitter from the USB port during software
installation process.
Insert the CD into the CD-ROM of your com-2.
puter, and the auto run program will load the
GUW101A Software Installation window.
Click on3. Update USB Transmitter to continue.

12
13
When you are prompted with the HWA4.
Firmware Update Tool general notes, click
and drag the side bar to the bottom and
click on Next to continue.
Click on5. Next to continue.

12
13
Click on6. Continue Anyway to continue. Click on7. Next to continue.

14
15
When prompted by this message, click on8. OK
to continue.
The rmware updating process is now 9.
completed and it will take up to a minute to
complete the process. Click on Finish to
close the update tool.

14
15
Update Wireless VGA Receiver
Insert the CD into the CD-ROM of your1.
computer, and the auto run program will
load the GUW101A Software Installation
window.
Click on2. Update Video Receiver to
continue.

16
17
Follow the instructions on the prompted3.
window. Plug the mini-B end of the included
USB cable to the mini-B connector on the
Wireless Video Receiver. Plug the type-A
end of the USB cable into an available port
of your computer. Make sure to have the
power adapter connected to the Wireless
Video Receiver and the Wireless Video
Receiver is powered on. Click on Next to
continue.

16
17
Click on4. OK to continue. Click on5. Next to continue.

18
19
Click on6. Finish to complete the update process. DO NOT7. disconnect the Wireless Video
Receiver from your computer. Unplug the
power adapter and plug it back into the
Wireless Video Receiver, then click OK to
continue.

18
19
Click8. OK to continue.
Unplug the power adapter and plug it back9.
into the Wireless Video Receiver, then click on
OK to complete the update process. Now you
can disconnect the Wireless Video Receiver
from your computer, and keep the power
adapter connected to the Wireless Video
Receiver. All connection should resume normal
automatically.

20
21
Update/Install Wireless USB Manager
Insert the CD into the CD-ROM on your1.
computer, the auto play program will launch
on its own. Click on Run CD_Start32.exe
or Run CD_Start64.exe (depends on the
version of Vista OS that you are using) to
continue.
Software Installation – For Vista users
Click on2. Install Wireless USB Manager to
continue.