IOGear GUWAVKIT User manual

1
Installation
Installation Guide
Wireless Audio / Video Kit
GUWAVKIT

2
3

2
3
Table of Contents
System Requirements 4
Important Information 5
Package Contents 6
Device Overview 7
Preparing for Setup 10
Software Installation – Windows XP 13
Software Installation – Windows Vista 17
Install Wireless USB Transmitter 21
Install Wireless VGA Receiver 22
Installing Wireless Audio Receiver 28
Connecting the Audio Receiver to Speakers 31
Advanced Settings – Wireless USB Manager 33
Advanced Settings – Video Mode Conguration 35
Advanced Settings - Screen Resolution Conguration 38
Advanced Settings - Wireless USB Transmitter Settings 41
Advanced Settings - Wireless USB Transmitter Selection 43
Advanced Settings - Wireless USB Transmitter Reset 44
Advanced Settings - Wireless VGA Receiver in Wired Mode 45
Trouble Shooting Guide 46
Technical Specications 67
Appendix 68
Limited Warranty 70
Federal Communications Commission (FCC) Statement 71
Contact 72

4
5
System Requirements
Microsoft Windows® XP (SP2) or Vista (32- / 64-bit) with available USB 2.0 port•
1.6 GHz processor (CPU) with 1GB of system memory (RAM)•
Flat-panel (LCD / Plasma / DLP) TV display or Projector with VGA (RGB / D-sub•
15-pin / PC) or DVI port (Does NOT work with CRT tube TV and DVI-D connector)
TV or audio system with 3.5mm audio jack or RCA connectors•
Minimum system requirement to play online video clips in a “window” – 1.6 Ghz
Atom™ with 1GB RAM, 480p video in a “window” – 1.8 Ghz Pentium™ M with 1GB
RAM, 720p video in a “window” – 2.8 GHz Pentium™ M with 1 GB RAM, 720p
video in “full screen” – 2.8 GHz Core™ 2 Duo with 1GB RAM.

4
5
Important Information
Before you get started, please NOTE:
Do not place Wireless USB devices under direct sunlight or near high heat emitting devices;
Do not place Wireless USB devices near water or wet surfaces to avoid electric hazards;
Do not place Wireless USB devices on any moving or unstable surfaces.

6
7
Package Contents
LINK PWR
• 1 x Wireless Video
Receiver (for display)
• 1 x Wireless Audio
Receiver (for stereo)
• 1 x Wireless USB
Transmitter (for
computer)
• 1 x USB 2.0 A to mini-B cable (3 ft.)
• 1 x USB 2.0 extension cable (4 ft.)
• 1 x Gold Plated VGA cable (6 ft.)
• 1 x VGA (F) to
DVI-A adapter
• 1 x 3.5mm to 3.5mm cable
• 1 x 3.5mm to RCA cable • 1 x Hook-and-loop
fastener
• 1 x Power adapter for Audio Receiver
• 1 x Power adapter for Video Receiver
• 1 x User Manual
• 1 x Installation CD
• 1 x Warranty /
Registration Card

6
7
Device Overview
1. LINK: Data Transfer Activity Indicator
LED blinks when data is being transferred-
2. PWR: Power
LED is solid when powered by the PC-
3. USB Connector
Connect to any available USB 2.0 port on your computer-
LINK PWR
12
3
Wireless USB Transmitter

8
9
132
5 6 7 8 94
Wireless Video Receiver
1. VGA : VGA Activity Indicator
LED is solid when display cable is-
connected
LED is blinking when data is being-
transferred
2. PWR: Power Indicator
LED is solid when power is applied-
3. Status Indicator
Single* solid light: device is wirelessly-
connected to the selected Wireless USB
Transmitter
Single* slowly blinking light: device-
is searching for a Wireless USB
Transmitter
Single* quickly blinking light: device is-
trying to connect to a Wireless USB
Transmitter
Rapidly scrolling lights: device is used in-
wired mode.
Three Simultaneous Blinking Lights:-
Cable Association Mode
*Only one light at a time. The position
of the light indicates which Wireless
USB Transmitter the device is trying to
communicate with.
4. VGA Connector
Connects to one end of the included-
VGA cable, and the other end to the
VGA or DVI port on your display
5. Power Plug
Power adapter socket-
6. RESET Button
Association history can be erased by-
pressing and holding this button for 10
seconds. (Please visit P.44 for details)
7. HOST Button
This button is used to select a different-
Wireless USB Transmitter. (Please visit
P.43 for details)
8. Mini-B USB port
In wireless mode, this port is used-
for cable association. (Please visit
Appendix for details)
In wired mode, connect the VGA-
adapter with the USB cable via this port
for wired operation. (Please visit P.45
for details)
9. WIRELESS/WIRED switch
Choose from wired or wireless mode by-
using this switch - P.45

8
9
Wireless Audio Receiver
1. Power/Activity LED
LED is solid when connection is established-
LED is blinking when power is on and connection is not established-
2. 3.5mm Audio Socket
Connects to the 3.5mm audio connector of the included 3.5mm or RCA audio cable,-
and the other end to the available 3.5mm audio socket or RCA audio socket on your
display or stereo system
3. Mini-B USB Port
Connects to the mini-B end of the included USB cable, and the Type-A end to an-
available USB port on your computer to create association between your computer and
the audio receiver
4. Power plug
Power adapter socket-
1
2
3
4

10
11
Preparing for Setup
Before you begin, please make sure to properly remove all previously installed
Wireless USB Manager and DisplayLink drivers from your system to avoid driver
conict. To properly remove previously installed drivers, please follow below
instructions.
Go to Start -> Control Panel -> Add or Remove Programs1.
Select any previously installed DisplayLink software and click on2. Remove button to
properly uninstall the program.
For Windows XP users
After all DisplayLink software are uninstalled, please restart your system.3.
Repeat steps 1 and select any previously installed Wireless USB drivers and click on4.
Remove button to properly uninstall the program.