IPC Gansow CT160 User manual

PLDC01851
CT160 Quick Guide
This Guide is intended for quick consultation only and does not replace the Use and Maintenance Manual.
Before using the machine, read the Use and Maintenance Manual contained in the machine packaging thoroughly and rigorously respect all the
instructions.
PREPARATION/
OPERATION
1. Fill the detergent tank.
2. Raise the side flaps and
insert the brushes under
the head, making sure they
rest against the aligners.
3. Turn the ignition key to
switch the machine on.
4. To attach the brushes
automatically, proceed as
follows:
Press the "Click-Off-On"
button. The machine first
performs a release
operation, then immediately
afterwards enables the
attachment operation.
Press the "Click-Off-On"
button again to
automatically attach the
brushes.
5. Select the most suitable
cleaning programme
according to the surface
and dirt to be removed:
P1: light cleaning
programme
P2: medium cleaning
programme
P3: heavy cleaning
programme.
After the cleaning
programme has been
selected, the machine
chooses the advance
speed and quantity of
detergent, then turns the
suction and brush motors
on.
6. The machine can be
operated without using the
3 cleaning programmes
provided by the
manufacturer. In this case,
the brush and suction
motors must be turned on
and the quantity of
detergent regulated
manually by pressing the
buttons shown.
7. Choose the direction of
movement by moving the
direction selector.
Select maximum speed by
turning the potentiometer.
8. Operate the machine
movement pedal.
9. If necessary, release the
service or parking brake.
10. Begin working.
11. When you have finished
cleaning, proceed as
follows:
•Turn the brush/suction
motor off.
•Turn the ignition key.
•If necessary, charge the
batteries.

PLDC01851
DAILY MAINTENANCE
Empty the dirty water drum
through the drain hose.
Clean the dirty water drum with
water or water and detergent.
Check the suction filter is
undamaged and clean.
Check the detergent output filter
is undamaged and clean.
Clean the brushes.
Check the detergent tank fill filter
is undamaged and clean.
Check the squeegee is clean and
the blades are not damaged.
Check the battery charge shown
on the display.
To charge, insert the battery
charger connector in the
connector under the seat.
REPLACING THE SQUEEGEE BLADES
Front:
•unscrew the screws fixing the blade retainer;
•remove the blade retainer;
•remove the blade;
•put the same blade back, reversing the edge in contact with the floor, or replace with a new one;
•reposition the blade retainer and fix with the screws;
Back:
•unscrew the screws fixing the blade retainer;
•release the clip;
•remove the blade retainers;
•remove the blade;
•put the same blade back, reversing the edge in contact with the floor until all four edges are worn, or replace with a new one;
•replace the two blade retainers and clip and fix with the screws.
BRUSH ATTACHMENT/RELEASE
Attaching:
Press the "Click-Off-On" button. The machine first performs a release operation, then immediately afterwards enables the attachment operation. Press
the "Click-Off-On" button again to automatically attach the brushes.
Releasing:
Press the "Click-Off-On" button, the machine releases the brushes.
TROUBLESHOOTING
THE MACHINE DOES NOT COME ON/START UP CHECK THE EMERGENCY BUTTON IS NOT PRESSED
CHECK THE BATTERY CHARGE
THE SUCTION MOTOR DOES NOT WORK CHECK THE DIRTY WATER DRUM IS NOT FULL
CHECK THE DIRTY WATER DRUM LEVEL SENSOR IS NOT BLOCKED/MALFUNCTIONING
THE MACHINE LEAVES THE FLOOR WET
CHECK THE SQUEEGEE BLADES ARE NOT WORN
CHECK THERE IS NO DEBRIS BETWEEN THE TWO SQUEEGEE BLADES
CHECK THERE IS NO DEBRIS IN THE SUCTION HOSE
CHECK THE SUCTION FILTER IS UNDAMAGED AND CLEAN
CHECK THE DIRTY WATER DRUM LID SEAL IS UNDAMAGED.
CHECK THE SUCTION HOSE IS CORRECTLY ATTACHED TO THE SQUEEGEE
THE MACHINE LEAVES THE FLOOR DIRTY CHECK THE TYPE OF BRUSH/PAD IN USE IS SUITABLE FOR THE TYPE OF DIRT AND FLOOR.
THE MACHINE LEAVES STRIPES OF WET FLOOR
CHECK THE FLOOR HAS BEEN BRUSHED BEFORE USING THE MACHINE
CHECK THERE IS NO DEBRIS BETWEEN THE TWO SQUEEGEE BLADES
CHECK THE SQUEEGEE BLADES ARE NOT WORN
CHECK THE SQUEEGEE IS CORRECTLY ADJUSTED