IPGARD SDVN-8S User manual

DESIGNED
AND MADE
IN THE USA
NOTICE
The information contained in this document is
subject to change without notice. iPGARD makes
no warranty of any kind with regard to this material,
including but not limited to, implied warranties of
merchantability and tness for particular purpose.
iPGARD will not be liable for errors contained herein
or for incidental or consequential damages in
connection with the furnishing, performance or use
of this material. No part of this document may be
photocopied, reproduced, or translated into another
language without prior written consent from
iPGARD, Inc.
20170523
SDVN-8S
Secure KVM Switch
Advanced 8-Port Secure Single-head
DVI-I KVM Switch with Audio
Quick Start Guide
A full Manual can be downloaded from
www.ipgard.com/documentation/
Toll Free: [phone]
Phone: [phone]
Fax: [phone]
3291 N. Jones Blvd.,
Las Vegas, NV 89108
iPGARD.COM
TECHNICAL SPECIFICATIONS WHAT’S IN THE BOX
VIDEO
Format DVI-I Dual Link
Host Interface (8) DVI-I 29-pin (female)
User Console
Interface (1) DVI-I 29-pin (female)
Max Resolution 2560 x 1600 @ 60Hz
DDC 5 volts p-p (TTL)
Input Equalization Automatic
Input Cable Length Up to 20 ft.
Output Cable Length Up to 20 ft.
USB
Signal Type USB 1.1 and 1.0 Keyboard
and Mouse only.
USB Type B Inputs (8) Keyboard-Mouse
User Console
Output Interface
(2) USB Type-A for keyboard
and mouse connection only
AUDIO
Input (8) Connector Stereo 3.5mm
Female
Output (1) Connector Stereo 3.5mm
Female
POWER
Power Requirements 12V DC, 3A power adapter with
center-pin positive polarity
ENVIRONMENT
Operating Temp 32° to 104° F (0° to 40° C)
Storage Temp -4° to 140° F (-20° to 60° C)
Humidity 0-80% RH, non-condensing
CERTIFICATIONS
Security Accreditation
Common Criteria Validated To
NIAP, Protection Prole PSS
Ver. 3.0
OTHER
Emulation USB 1.1 and USB 2.0
Compatible
Control Front Panel Buttons
PART NO. QTY DESCRIPTION
SDVN-8S 18-port, SH Secure DVI-I KVM
Switch
PS12VDC3A 112V DC, 3A power adapter with
center-pin positive polarity.
1Quick Start Guide

DESIGNED
AND MADE
IN THE USA
DVI-I IN
AUDIO OUT
DVI-I OUT
USB IN
USB OUT
AUDIO IN
SDVN-8S
SDVN-8S
1 2 3 4 5 6 7 8
EDID LEARN HARDWARE INSTALLATION
A full Manual can be downloaded from
www.ipgard.com/documentation/
The KVM is designed to learn a connected
monitor’s EDID upon power up. In the event
of connecting a new monitor to the KVM, a
power recycle is required.
The KVM will indicate the unit’s EDID learn
process is active by ashing the front panel’s
LEDs. In sequential order. Starting with the
LED above button “1” on the front panel,
each LED will ash green for approximately
10 seconds upon beginning the EDID
learn. Once all the LEDs stop ashing, the
LEDs will cycle and the EDID learn will be
complete.
A monitor must be connected to the video
output port located in the console space at
the back of the KVM during the EDID learn
process.
If the read EDID from the connected monitor
is identical to the current stored EDID in the
KVM then the EDID learn function will be
skipped.
1. Ensure that power is turned off or disconnected from the unit and the computers.
2. Use DVI cables to connect the DVI output ports from each computer to the corresponding
DVI-I IN ports of the unit.
3. Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the respective
USB ports of the unit.
4. Optionally connect a stereo audio cable (3.5mm to 3.5mm) to connect the audio output of
the computers to the AUDIO IN ports of the unit.
5. Connect a monitor to the DVI-I OUT console ports of the unit using DVI cables.
6. Connect a USB keyboard and mouse in the two USB console ports.
7. Optionally connect stereo speakers to the AUDIO OUT port of the unit.
8. Finally, power on the KVM by connecting a 12VDC power supply to the power connector, and
then turn on all the computers.
Note: The computer connected to port 1 will always be selected by default after power up.
Note: You can connect up to 8 computers to the 8 port KVM.
A full Manual can be downloaded from
www.ipgard.com/documentation/