IPGARD SDVN-44-X User manual

DESIGNED
AND MADE
IN THE USA
12VDC3.0A
DVI OUT 1 DVI OUT 2 DVI OUT 3 DVI OUT 4 DVI IN 1 DVI IN 2 DVI IN 3 DVI IN 4
Audio
K/M
CAC
Audio
K/M
CAC
Audio
K/M
CAC
Audio
K/M
CAC
K/M
CAC
Audio
K/M
CAC
Audio
K/M
CAC
Audio Audio
K/M
CAC
OUT-1 OUT-2 OUT-3 OUT-4IN-4IN-3IN-2IN-1
SELECT
SOURCE
USB
SELECTOR
CONSOLE 1
SELECT
SOURCE
USB
SELECTOR
CONSOLE 2
SELECT
SOURCE
USB
SELECTOR
CONSOLE 3
SELECT
SOURCE
USB
SELECTOR
CONSOLE 4
SDVN-44-X
TECHNICAL SPECIFICATIONS WHAT’S IN THE BOX
VIDEO
Format DVI-D Dual Link
Host Interface (4) DVI-D (female)
User Console
Interface (4) DVI-D (female)
Max Resolution 1080p and 4K/30Hz
DDC 5 volts p-p (TTL)
Input Equalization Automatic
Input Cable Length Up to 20 ft.
Output Cable Length Up to 20 ft.
USB
Signal Type
USB 1.1 and 1.0 Keyboard and
Mouse only.
USB 2.0 for CAC connection.
USB Type B Inputs (4) Keyboard-Mouse; (4) CAC
User Console
Output Interface
(4) Dual USB Type-A for
keyboard/mouse connection.
(4) Single USB Type-A for CAC
connection.
AUDIO
Input (4) Connector Stereo 3.5mm
Female
Output (4) Connector Stereo 3.5mm
Female
POWER
Power Requirements 12V DC, 2A power adapter with
center-pin positive polarity
ENVIRONMENT
Operating Temp 32° to 104° F (0° to 40° C)
Storage Temp -4° to 140° F (-20° to 60° C)
Humidity 0-80% RH, non-condensing
CERTIFICATIONS
Security Accreditation
Common Criteria Validated To
NIAP, Protection Prole PSS
Ver. 3.0
OTHER
Emulation USB 1.1 and USB 2.0
Compatible
Control Front Panel Buttons
PART NO. QTY DESCRIPTION
SDVN-44-X 14-port, Secure DVI-D KVM
Matrix Switch (4 Users)
PS12VDC2A 112V DC, 2A power adapter with
center-pin positive polarity.
1Quick Start Guide
Toll Free: [phone]
Phone: [phone]
Fax: [phone]
3291 N. Jones Blvd.,
Las Vegas, NV 89108
iPGARD.COM
NOTICE
The information contained in this document is
subject to change without notice. iPGARD makes
no warranty of any kind with regard to this material,
including but not limited to, implied warranties of
merchantability and tness for particular purpose.
iPGARD will not be liable for errors contained herein
or for incidental or consequential damages in
connection with the furnishing, performance or use
of this material. No part of this document may be
photocopied, reproduced, or translated into another
language without prior written consent from
iPGARD, Inc.
20170518
SDVN-44-X
Secure KVM Matrix Switch
Advanced 4-Port Secure
DVI-D Matrix KVM Switch
with Audio, KB/Mouse
USB Emulation and
CAC Support (4 Users)
Quick Start Guide
A full Manual can be downloaded from
www.ipgard.com/documentation/

DESIGNED
AND MADE
IN THE USA
AUDIO IN
CAC IN
DVI-D IN
USB IN
Input Connectivity
Output Connectivity
AUDIO OUT
CAC OUT
DVI-D OUT
USB OUT
SDVN-44-X
SELECT
SOURCE
USB
SELECTOR
CONSOLE 1
SELECT
SOURCE
USB
SELECTOR
CONSOLE 2
SELECT
SOURCE
USB
SELECTOR
CONSOLE 3
SELECT
SOURCE
USB
SELECTOR
CONSOLE 4
SDVN-44-X
EDID LEARN HARDWARE INSTALLATION
A full Manual can be downloaded from
www.ipgard.com/documentation/
The Secure KVM Switch is designed to learn
a connected monitor’s EDID upon power up.
In the event of connecting a new monitor to
the Secure KVM Switch, a power recycle is
required.
The Secure KVM Switch will indicate the
unit’s EDID learn process is active by
ashing the front panel’s LEDs. In sequential
order. Starting with the LED above button
“1” on the front panel, each LED will ash
green for approximately 10 seconds upon
beginning the EDID learn. Once all the LEDs
stop ashing, the LEDs will cycle and the
EDID learn will be complete.
A monitor must be connected to the video
output port located in the console space at
the back of the Secure KVM Switch during
the EDID learn process.
If the read EDID from the connected monitor
is identical to the current stored EDID in
the Secure KVM Switch then the EDID learn
function will be skipped.
1. Ensure that power is turned off or disconnected from the unit and the computers.
2. Use a DVI cable to connect the DVI output port from each computer to the corresponding
DVI-D IN ports of the unit.
3. Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the respective
USB ports of the unit.
4. Optionally connect a stereo audio cable (3.5mm to 3.5mm) to connect the audio output of
the computers to the AUDIO IN ports of the unit.
5. Connect a monitor to the DVI-D OUT console port of the unit using a DVI cable.
6. Connect a USB keyboard and mouse in the two USB console ports.
7. Optionally connect stereo speakers to the AUDIO OUT port of the unit.
8. Optionally connect CAC (COMMON ACCESS CARD, SMART CARD READER) to the CAC port in
the user console interface.
9. Finally, power on the KVM by connecting a 12VDC power supply to the power connector, and
then turn on all the computers.
Note: The computer connected to port 1 will always be selected by default after power up.
Note: You can connect up to 4 computers to the 4 port KVM.
A full Manual can be downloaded from
www.ipgard.com/documentation/