iPuray BRT-105 Installation instructions

Product Specifications of BRT-105 Page 1of 4
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
Timer Switch
Model #：BRT-105
Features:
BRT-105 is a timer switch which has an On/Off button on the front and a keypad panel behind its
front plate. The keypad panel is used for setting up the clock and delay off time. This unique
design makes it easy to operate, and prevents the timer settings from being changed accidentally. It
is also designed for easy installation and retrofit, directly fit into standard wall box.
Delay off time up to 30 minutes, which can be set accurately to a second;
LCD display showing the current time and the current status of the switch;
Operates on AC L and N wiring;
Good for all kinds of loads (Resistive, inductive, and capacitive);
ABS-V0 flame resistance material; and
Classical 86 series design and high quality build.
Front View, Back View and Hidden Panel:
Fig. 1 and Fig. 2 show the front view and the back view of the BRT-105 timer switch respectively.
Fig. 1 Front View Fig. 2 Back View
Product Specifications

Product Specifications of BRT-105 Page 2of 4
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
As shown in Fig. 1, the BRT-105 timer switch has an LCD display and an On/Off buttons in the
front. The LCD display shows the current time and the current status of the switch. The On/Off
button is used for turning on or turning off a load.
When the On/Off button is pressed and the display shows On,
The load will be turned on immediately; and
When the On/Off button is presses again and the display will show Off,
If there is no delay off time being set, the load will be turned off immediately; or
If there is delay off time being set, the load will be turned off only after the preset delay off
time runs out. Meanwhile, the display will show a “bell” sign. Press the On/Off button will
cancel the delay off operation and turn off the load immediately.
Fig.3 Hidden 9 Keypad Panel
As shown in Fig. 3, the front plate can be flipped down from the top edge. A 9 keypad panel
hidden behind the front plate is used for setting up the timer. Please refer to “BRT-105 Timer
Switch Setup” for details.
Specification Parameters:
Input Voltage
220～240V(50Hz/60Hz)
Operation
Environment
No-condensation 20-90% RH，
-20℃～40℃
Wattage
Resistive: 2000W
Inductive: 1000W
Capacitive: 400W
Load type
All Types
Mounting Hole
Spacing
60mm
Matching
Box
75mm x 75mm x 50mm
Dimension
86mm x 86mm x 43mm
Weight
72g

Product Specifications of BRT-105 Page 3of 4
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
Wiring Diagram and Installation Guide:
BRT-105 timer switch requires both hot wire and neutral wire for installation:
Hot wire (ACL): Coming from the power line with 220V;
Neutral wire (ACN): Usually coming with the hot wire; and
Load wire: Going to the load.
Fig. 4 BRT-105 Timer Switch Wiring Diagram
Warning: Please make sure power is turned off before starting installation!
Fig. 4 shows the wiring diagram and Fig. 5 shows the step-by-step installation instructions. There
are three easy steps:
Step one: Use a screwdriver to pry off the front plate in position A;
Step two: Wiring according to the diagram and the labelled ports of the switch; and
Step three: Install screws and front plate.
Fig. 5 BRT-105 Timer Switch Installation Guide

Product Specifications of BRT-105 Page 4of 4
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
BRT-105 Timer Switch Setup:
1. Power the switch with 220 voltages: following the wiring diagram and Installation Guide.
2. Flip down the front plate from the top edge.
3. Set up Time and Date: Press the SET button, the displayed hours will flash, and then press
–or +to adjust the hours. Press the SET button again, the displayed minutes will flash, and
then press –or +to adjust the minutes. Press the SET button again, the displayed date will
flash, and then press – or + to adjust the date. Finally, press the SET button to finish and the
settings are saved.
4. Set up Delay off Time: The longest delay off time is 30 minutes. Press the Ⅱbutton to set
the minutes, and then press button ◁or ▷to adjust the minutes. Press the Ⅱbutton again to
set the seconds, and then press button ◁and ▷to adjust the seconds. Finally, press and hold
the Ⅱbutton to save the settings or the settings will be saved automatically if there is no
keypad operation for 15 seconds.
Once the settings are finished, flip up and close the front plate. The delay off time can be
deleted following Step 2 and Step 5 below.
5. Delete the Delay off Time setting: Press the Ⅱbutton to set the minutes to 00 using –or
+, and press the Ⅱbutton again to set the seconds to 00 using –or +. The switch will just
have a basic ON/OFF function.
Applications:
BRT-105 timer switch can be used for automatically turning off all kinds of loads such as fans,
lights, appliances, or other kinds of electrical equipment. They are perfect for saving energy and
bringing convenience and safety to our daily life and work.
The elegant design of BRT-105 timer switch makes it suitable for wide applications at various
locations such as homes, schools, laboratories, hospitals, offices, etc., especially for luxurious
hotels and high-grade villas.
How to Order:
Please contact us: Shenzhen Asia Bright Industry Co., Ltd
Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China
Tel: [phone] 89748211 89748345
Fax: [phone] [phone]
Email: [e-mail] Website: www.a-brt.com