Ironman Fitness Triathlon X-Class 510 User manual

The specifications of this product may vary from this photo and are subject to change without notice.
IRONMAN, IRONMAN TRIATHLON and M-DOT are registered trademarks of World Triathlon Corporation.
This product is licensed by the World Triathlon Corporation.
Model 6252
Triathlon X-Class 510
Exercise Bike
1

6252.1-112714
2
2

SERVICE ------------------------------------------------------------------------ 4
LABEL PLACEMENT --------------------------------------------------------- 5
PRODUCT SAFETY ---------------------------------------------------------- 6
OVERVIEW DRAWING ------------------------------------------------------ 7
HARDWARE AND TOOLS LIST ------------------------------------------- 9
PART LIST ---------------------------------------------------------------------- 10
ASSEMBLY --------------------------------------------------------------------- 12
COMPUTER -------------------------------------------------------------------- 21
HEART RATE CHEST BELT ---------------------------------------------- 23
HOW TO USE ----------------------------------------------------------------- 19
TROUBLESHOOTING & MAINTENANCE ----------------------------- 25
WARM UP ----------------------------------------------------------------------- 24
WARRANTY -------------------------------------------------------------------- 26
FAX FORM ---------------------------------------------------------------------- 27
TABLE OF CONTENT
3
3
3

IMPORTANT: FOR NORTH AMERICA ONLY
To request product service and order
replacement parts, please call our
customer service department at:
1-844-641-7922
Monday through Friday, 8:00 AM-5:00 PM Pacific Standard Time,
or email us at: [e-mail]
Please visit our website at www.paradigmhw.com.
Please have the following information ready when requesting for service:
Your name
Phone number
Model number
Serial number
Part number
Proof of Purchase
Before returning this product to the store please contact
customer service at the contact number.
Paradigm Health & Wellness, Inc.
1189 Jellick Ave
City of Industry, CA 91748 USA
SERVICE
4

LABEL PLACEMENT
5
5

PRODUCT SAFETY
Basic precautions should always be followed, including the following safety
instructions when using this equipment. Read all instructions before using
this equipment.
1. Read all the instructions in this manual and do warm up exercises before
using this equipment.
2. Before exercising and to avoid injuring your muscles, perform warm-up
exercise for each muscle group is highly recommended. Please refer to
Warm Up section of the Owner’s Manual.
3. Please make sure all components are not damaged and in working order
before use. This equipment should be placed on a flat surface while in use.
Using a mat or other material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not
wear clothes that might get caught on any part of the equipment.
5. Do not attempt any maintenance or adjustments other than those described
in this manual. Should any problems arise, discontinue use and consult
with customer service at Paradigm Health and Wellness.
6. Keep dry - do not operate in wet or moist condition.
7. Do not use the equipment outdoors.
8. This equipment is for household use only.
9. Only one person should be on the equipment at any time.
10. Keep children and pets away from the product while in use.
11. This machine is designed for adults only.
12. This product requires a minimum of 6 feet of space for safe operation.
13. If you feel any chest pains, nausea, dizziness, or shortness of breath, you
should stop exercising immediately and consult your physician before continuing.
14. The maximum weight capacity for this product is 300 lbs/136 kgs.
WARNING: Before beginning any exercise program consult your
physician. This is especially important for the people who are over 35 years
old or who have pre-existing health problems. Read all instructions before
using any fitness equipment.
CAUTION: Read all instructions carefully before operating this
product. Retain this Owner’s Manual for future reference.
6

7
OVERVIEW DRAWING

8
OVERVIEW DRAWING

(#29) Hex Screw
M6x8mm 1PC
(#104) Allen Wrench
4mm 1PC
(#105)Allen Wrench
5mm 1PC
(#103)Allen Wrench
3mm 1PC
(#106) Allen Wrench with
Screwdriver 6mm 1PC
(#107)Thread Sealant
1PC
(#102) Wrench Tool
13,14,15,17mm 1PC
(#3) HEXAGONAL BOLT
M10×L:55(mm) 4PCS
(#4) Washer ˜10× 20×t2.0(mm)
4PCS
9
HARDWARE & TOOL LIST

No.
Description
Qty
No.
Description
Qty
001 PEDAL(L)
025 POST BUSHING 120L×12405W×46.5H(mm)
002 PEDAL(R)
026 SPACER ˜14× 30(mm)
003 HEXAGONAL BOLT M10×L:55(mm)
027 FIXED HANDLE
004 WASHER ˜10×
028 MUDGUARD
005
Seat Cushion
029 HEXAGONAL SCREW M6×8(mm)
030 MIDDLE BRAKE AXLE
007 MAIN FRAME SET
031
008 BEARING-6004ZZ ˜20× ˜ 42×12 (mm)
009 CRANK AXLE
010
011 RUBBER CAP˜60×
012 CRANK
013 PREVAILING TORQUE HEX FLANGE NUT
014 CRANK CAP˜23×
015
FLYWHEEL AXLE
016 WASHER ˜18× ˜ 8.5×t:
017
CAP NUT M8x6.5t mm
018 BELT
019 SCREW M5×10(mm)
020 BOLT
021 LEFT SIDE COVER
022
023
DECORATIVE COVER (R)
024 SCREW M5×15(mm)
PARTS LIST
10
053 ADJUSTABLE KNOB 2
054 HANDLEBAR SET 1
1
1
055 SPACER˜22× 16(mm) 2
056 KNOB TOP 2
2
049 CRANK 1
050 BOLT M10×15(mm) 5
5
051 SPRING WASHER M10(mm)
052 HANDLEBAR SLIDER 1
032 HEXAGONAL NUT M8×7(mm) 1
033 LOWER BRAKE AXLE 1
034 BRAKE BALANCE BAR 1
035 BRAKE PAD 1
036 BRAKE BALANCE BUSHING 1
037 SPRING 37×20ט1.5(mm) 1
038 SPRING ˜15× ˜ 2.3×25(mm) 1
039 BRAKE WASHER
˜16. 8×t:3(mm)
040 HEXAGONAL BOLT 2
041 HEXAGONAL BOLT M6×L:30(mm) 2
042 WASHER ˜6× ˜ 12×t:2(mm) 5
043 HEXAGONAL NUT M6 1
1
044 HEXAGONAL NUT M6 1
045 HEXAGONAL SCREW 2
046 RUBBER KNOB ˜50× 57(mm) 5
047 SPECIAL NUT L:58×W:50×H:15(mm)
048 BELT PULLEY 1
3
1
2
1
2
4
2
20×t2.0(mm) 4
1
1
4
1
1
BRAKE HEXAGONAL SLEEVE 2
4
1
HEXAGONAL NUT M20 1
L:23(mm) 1
1
2
8(mm) 2
1
2(mm) 2
2
1
3
4
1
DECORATIVE COVER (L) 1
1
4
4
TRUSS SCREW M4×8(mm)
4
WASHER L:52×W:26×H:2(mm)
BOTTLE HOLDER PALTE
HEXAGONAL SCREW M6×15(mm)
UPPER SLIDER END CAP 50Lx40Wx15H(mm)
057
058
059
060
061
10

PARTS LIST
11
072 HEXAGONAL SCREW M6×8(mm)
073 SEAT SLIDER
074 SEAT ADJUSTABLE POST
075 LOWER SLIDER END CAP 34L×24.5W×16H(mm)
1
1
1
1
1
095 MAGNET˜10× 7mm)
102 WRENCH TOOL 13,14,15,17 mm
1
1
1
1
1
1
096 UPPER BRAKE AXLE 1
103Allen Wrench 3mm
097 HEXAGONAL BUSHING COVER 1
1
104Allen Wrench 4mm
098 ADJUSTABLE KNOB
105Allen Wrench 5mm
099 KNOB TOP 1
106Allen Wrench with
Screwdriver 6mm
100 Sensor Wire(UP) 1
1
107THREAD SEALANT
101 Sensor Wire(DOWN)
No.
Description
Qty
No.
Description
076 FRONT STABILIZER SET
077 FRONT STABILIZER CAP 97L×50W×40H(mm) 2
078 HEXAGONAL NUT M10×8(mm) 3
079 WHEEL 2
080 HEXAGONAL SCREW M8×L:40(mm) 2
081 HEXAGONAL NUT M8 3
082 REAR STABILIZER SET 1
083 REAR STABILIZER CAP L:123xW:5 0XH:40(mm) 2
084 ANTI-SLIP PAD 1
062 RUBBER PAD 1 085
HEXAGONAL SCREW
M5×10(mm)
063 BOLT 2 086 FLYWHEEL 1
064 WASHER 2 087 AXLE SLEEVE 1
065 BOLT 2 088 WASHER ˜27× ˜ 20.5×t:3(mm)
066 CONSOLE PLATE 1 089 CHAIN COVER 1
067 CONSOLE 1 090 DART-SHAPED COVER
068BOTTLE HOLDER 1 091 SELF-TAPPING SCREW
M3×8(mm
)
6
069 BOLT 2 092 FRONT LEFT COVER 1
070 HANDLEBAR ADJUSTABLE POST 1 093 HUB 2
2
2
071 LOWER SLIDE ENDCAP 34L×24.5W×16H(mm) 2 094 WASHER ˜21. 3×t=3.0(mm) 2
4
Qty
2
11

Step 1
Attach Front Stabilizer Set (#76) to frame with two Washers (#4) and two
Hexagonal Bolt (#3) and then tighten firmly by using Allen Wrench with
Screwdriver 6mm (#106)
Step 2
Attach Rear Stabilizer Set (#82) to frame with two Washers (#4) and two Hex
Bolts (#3), and then tighten firmly by using Allen Wrench with Screwdriver 6mm
(#106)
Hardware:
(#106) Allen Wrench with
Screwdriver 6mm 1PC
(#106) Allen Wrench with
Screwdriver 6mm 1PC
(#4) Washer ˜10× 20×t2.0(mm)
4PCS
(#3) HEXAGONAL BOLT
M10×L:55(mm) 4PCS
ASSEMBLY
12

.
Step 3
Fully coat entire threads with Thread Sealant (#107) on the thread of the Left
and Right Pedal (#1/ #2) before pedal assembly.
Before applying thread sealant, make sure parts are clean. Allow sealant to dry
for 12 hours to fully cure before use.
(#107)Thread Sealant
1PC
ASSEMBLY
13
13

(#102) Wrench Tool
13,14,15,17mm 1PC
Step 4
The Cranks and Pedals are marked “R” for Right and “L” for Left.
Left Pedal: Insert Left Pedal (#1) into threaded hole in the Left Crank (#12).
Using your hand, turn the pedal shaft counter-clockwise direction until snug.
Use the wrench, tighten the pedal shaft counter-clockwise
RightPedal: Repeat steps above but in clockwise direction
Left
Right
ASSEMBLY
14

Tool
Tool
Step 5
Insert 4 AA batteries (included) into the back of the Console (67). Attach the
Console (67) to the Console Plate (66), and then tighten Console Plate (66) to
Handlebar Set (54) with two Bolts (65). Note: Console should "click" into place.
Step 6
Attach Bottle holder plate (61) with two Washers (64) and two Bolts (63) to
the Handlebar set (54) and attach Bottle holder(68) to the Bottle Holder Plate
(61) with two Bolts (69).
ASSEMBLY
(#106) Allen Wrench with
Screwdriver 6mm 1PC
(#104) Allen Wrench
4mm 1PC
15

Step 7
Slide the Handlebar Set (54) onto the Handlebar Adjustable Post (70) in the direction shown above.
Hardwa
Tool
re
(#105)Allen Wrench
5mm 1PC
(#29) Hex Screw M6x8mm
1PC
ASSEMBLY
16
Install the Hex Screw (#29) from
underneath the Handlebar as shown on
the left. Tighten with Allen Wrench (#105).
Install the 2 Upper Slider End Caps
(#59) as shown on the left.
Note: Hex Screw and Upper Slider End Caps
were packaged with this manual.
#54
#70
#29
#59

Step 8
Insert the Sensor Wire (#100) into the Console (#67).
Step 9
Connect Sensor Wire (#100) with Speed Sensor Wire (#101)
ASSEMBLY
17
#100
#67
#100
#101

Step 10
Insert Seat Cushion (#5) into Seat Slider (#73) and tighten firmly by
using Wrench Tool (#102).
Step 11
The Bike should be on a level surface. Turn the Rubber Knob (#46) to raise or lower
to, make sure all Rubber Knobs touch the floor. Turn Special Nut (#47) clockwise to
lock the Rubber Knob in position.
(#102) Wrench Tool
13,14,15,17mm 1PC
ASSEMBLY
18
18

HOW TO USE
Seat height adjustment
Turn Fixed Handle (#27) counter-clockwise to unlock. Slide the
seat up or down to desire position. Turn Fixed Handle clockwise
to lock.
Do not raise the seat post over the STOP line
Seat slide adjustment
Turn Adjustable Knob (#53) counter-clockwise to unlock. Slide the
seat to desire position. Turn Adjustable Knob clockwise to lock.
Handlebar slide adjustment
Turn Adjustable Knob (#53) counter-clockwise to unlock. Slide
the handlebar to desire position. Turn Adjustable Knob clock-
wise to lock.
Handlebar height adjustment
Turn Fixed Handle (#27) counter-clockwise to unlock. Slide the
handlebar up or down to desire position. Turn Fixed Handle
clockwise to lock.
Do not raise the handlebar post over the STOP line
19
19

HOW TO USE
Tension Adjustment
Turn knob clockwise to increase tension
Turn knob counter-clockwise to decrease tension
Emergency Stop
Press down the knob to stop the flywheel
Foot Strap
Put your foot forward as possible into the shoe cage,
pull the foot strap snygly around your shoe to avoid
slipping off the pedal, see picture.
20