Irradian L203 Instruction Manual









 
  
   
    
   





  
    
   


Handbook Ref No. MH063/Issue L
File Ref: L203-v5L.doc









 
  
   
    
   





   
      
    


   
      
    1. Introduction
2. Specification
3. Operation
4. Illuminance Measurements
5. Luminance Measurements
6. Battery Replacement
7. Photopic Response
8. Cosine Angular Response
9. Calibration Description
10. Block Diagram
11. Programming via the RS232 Interface
12. Environmental Care, Recycling and Disposal
Handbook Update Log
Issue Date Pages changed
A 19/03/99 New Issue
B 19/12/99 Update for V4 programming
C 14/06/00 4,6,11,13,19-25: Update for V5 programming
D 04/01/01 Version 5 update
E 06/02/02 20: Programming update
F 22/05/02 8: CRT head update
G 23/02/06 7,17: Cosine response update
H 26/06/07 WEEE update
I 09/07/09 Contact details update
J 13/05/10 Contents layout
K 15/07/10 RS232 update
L 27/06/11 Specification update

L203 Photometer Irradian Limited
1


   
      
    


The Irradian L203 Digital Photometer is a portable instrument designed
for accurate measurement of luminous incidence or illuminance in lux (fc,
foot-candle) and luminous intensity or luminance in cd.m
-2
, candela per
square metre (fL, foot-Lambert). The model L203-LUX is available for
illuminance measurements only.
The photometers comprise of a hand held display unit, a detector
/amplifier assembly with connecting cable, an illuminance filter ring and a
luminance field of view probe. The sensor is a large area silicon
photodiode with excellent linearity and long term stability. The Irradian
photopic filter ring and photopic field of view probe, fitted to the front of
the silicon detector give a response which closely matches the human
eye response outlined by the CIE Vλcurve. This precise colour
correction gives high accuracy of photometric measurements from light
sources with different spectral distributions (see Calibration section).
For illuminance measurements, the Irradian photopic filter ring with
cosine corrected diffuser (model CIE Cos-112) is fitted to the detector
assembly. This will integrate light from all sources in the hemisphere in
front of the detector. Before leaving the factory, the instrument is
calibrated to read directly in lux and fc (foot-candle).
The L203 Photometer can also measure luminance directly. In this mode
of operation, the illuminance filter ring is removed from the detector
assembly and replaced with either a CIE FOV-112 luminance probe (with
a defined field-of-view of 6°) or a contact CIE FOV-101 CRT luminance
probe. In either case, where the luminance varies across the field of
view or probe area, the meter reading will represent the average
luminance. The photometer can measure in either cd.m
-2
or fL (foot-
Lambert).

Irradian Limited L203 Photometer
2
  
    
   

 


DISPLAY UNIT
Controller: 80C51 8bit micro-processor with a 3.1684MHz
clock.
Memory On board non volatile RAM for calibration
factors and set-up parameters.
Key Operation 8 switch key board with 11 LED indicators.
Power Switch Microprocessor reset at switch on.
Unit settings stored prior to shut down.
Serial Interface Three wire RS232 serial interface.
4800 baud, no parity, 1 stop bit.
Integration Time 0.33s
Conversion Scale 17 bit
Accuracy: Measurement accuracy ±1digit with a
linearity error of <1% from 1 to 100 000 lux.
Display: 4½ digit LCD display. Character height 10mm.
Display illumination: A LED back light can be switched on to
illuminate the display for readings in low
ambient light situations.
Power Supply: 9 volt 1200mAh, Lithium Manganese battery.
240V/110V AC Mains supply (optional).
Power Consumption: Shut down mode <5µA
Operating 10 - 20mA
LED back light ~20mA
Battery Life ~ 50 hours without backlight use

L203 Photometer Irradian Limited
3 
   
      
    (continued):


Ranges: i) Illuminance (both models)
Up to 6 full scale decades measuring from:
0 to 1.9999 lux
0 to 19.999 lux
0 to 199.99 lux
0 to 1999.9 lux
0 to 19999 lux
0 to 19999 x 10 lux
Resolution 0,0001 lux on range 1.
Up to 5 full scale decades measuring from:
0 to 1.9999 fc
0 to 19.999 fc
0 to 199.99 fc
0 to 1999.9 fc
0 to 19999 fc
Resolution 0,0001 fc on range 1.
ii) Luminance (model L203 only)
Up to 6
*
full scale decades measuring from:
0 to 1.9999 cd.m
-2
(
*
with CIE-FOV-112 only)
0 to 19.999 cd.m
-2
0 to 199.99 cd.m
-2
0 to 1999.9 cd.m
-2
0 to 19999 cd.m
-2
0 to 19999 x 10 cd.m
-2
Resolution 0,0001 cd.m
-2
on range 1
*
.
Resolution 0,001 cd.m
-2
(with CIE-FOV-101).
Up to 6 full scale decades measuring from:
0 to 1.9999 fL
0 to 19.999 fL
0 to 199.99 fL
0 to 1999.9 fL
0 to 19999 fL
0 to 19999 x 10 fL
Resolution 0,0001 fL on range 1.
Calibration Absolute calibration accuracy ± 5% traceable
to NPL standards.
Photopic colour correction integrated error of
± 1% over visible spectrum.

Irradian Limited L203 Photometer
4
   
      
    (continued):


Front Panel Controls:
RANGE Select auto ranging or manual range control.
UNITS Select between Lux and fc for illuminance
measurements and between cd.m
-2
and fL for
luminance measurements. Select AUX for
additional accessory calibration if fitted.
ZERO Initiates a zero or background measurement
routine on all gain ranges.
HOLD/RUN Display is held at present reading until HOLD
button is pressed again.
Select to run or hold a special mode.
MODE Select between AVERAGE, MIN, MAX and
INTEGRATE modes.
FUNCTION/RESET Press to reset function values to zero
RESET Press to return to normal measurement mode
from Manual range mode or special modes.
Note the display hold is not reset.
 Power on / off button
 Display backlight on off button.
Display backlight will switch off after a
programmable delay, factory setting 60 secs.
Connectors: 8 pin DIN type detector connector.
5 pin DIN type RS232 connector.
Single, 2 pole power connector (optional).
Temperature Range: 0 to 40°C. 80% RH.
Dimensions: 150 x 80 x 45mm.
High impact polystyrene.
Weight: 350g

L203 Photometer Irradian Limited
5 
   
      
    (continued):
LABORATORY DETECTOR, Model SD222
Amplifier PCB Photodiode
Cable
Accessory Mounting Thread
The SD222 laboratory detector comprises of a aluminium housing,
photodiode and PCB assembly.
Detector: 33mm² silicon photodiode.
Temperature Coefficient: -0.10 %/°C
Amplifier Gain 10
9
V/A to 10
3
V/A
Current to Frequency 0 - 0.5Mhz
Linearity Error: <1% from 1 to 100 000 lux
Temperature Range: Operation: -20 to +60°C
Storage: -20 to +70°C
Detector Housing: Black anodised aluminium alloy housing.
Each optical accessories screws into the
detector housing on a 1.125" x 20 T.P.I.
The detector amplifier is connected to the
display unit via a multicore cable to a eight pin
DIN type connector.

Irradian Limited L203 Photometer
6
   
      
    (continued):


PHOTOPIC FILTER RING, Model CIE Cos-112
Spectral Response: Refer Figure 1 and Section 7.
Angular Response: Illuminance measurements
Accurately cosine corrected to Lambert's Cosine
Law. Maximum error is less than ±3.5% from
true response to 70° from normal incidence,
reference Figure 2.
Filter ring assembly: Black anodised aluminium alloy ring with
screw thread 1.125" x 20 T.P.I.
Multiple coloured filter glasses individually
selected for close matching to Vλ..
Specially profiled acrylic diffuser for high
accuracy cosine angular response.
FIELD OF VIEW PROBE CIE FOV-112
Spectral Response: Refer Figure 1 and Section 7.
Angular Response: Luminance measurements (model L203 only)
The field of view is defined with FOV1 accessory
to 6°full angle.
FOV probe assembly: Black anodised aluminium alloy body with
screw thread 1.125" x 20 T.P.I.
Glass lens f/l 100mm, 25mm φ.

L203 Photometer Irradian Limited
7 
   
      
    (continued):
CRT SCREEN LUMINANCE PROBE CIE FOV-101
Spectral Response: Refer Figure 1 and Section 7.
Design: Aluminium tube; 10 mm internal diameter
with aperture, 24 mm (or 18 mm) external
diameter. Rubber O-ring tip.
Screw thread: 1"1/8 x 20TPI.

Irradian Limited L203 Photometer
8


 


SETTING UP
1) With the unit OFF, plug the detector 8 way connector into the socket
on the top of the display unit.
2) Carefully screw the filter ring for illuminance measurements, field of
view or contact probe for luminance measurements to the detector
housing. Note: Clean the white diffuser on the filter ring or the lens on
the field of view probe if they are marked or dirty.
3) Press and release the power switch on the L203 display key pad. The
micro controller will initiate with the display momentarily showing:-
The photometer will now search for the optimum range on the detector
amplifier. A typical display is shown below.
An LED will illuminate indicating the units. This will be the same units
prior to the last power off.
4) Press and release the UNITS switch to select the correct units
required. For illuminance measurements with the CIE Cos-112
photopic filter rings the correct units are either lux or fc. For luminance
measurements with the CIE FOV-112 photopic field of view or contact
probe the correct units are either cd.m
-2
or fL.
5) It is recommended that the photometer amplifier is nulled periodically.
Place the cover over the filter ring or the end of the field of view or
contact probe. Press and release the ZERO switch, the display will
momentarily show:-

L203 Photometer Irradian Limited
9 


 (continued):


6) The micro controller will now measure the amplifier offset on each of
the gain ranges and store these values in the non volatile memory. All
subsequent measurements will first have one of these offsets
subtracted before displaying the measurement.
At the end of the nulling sequence the display will show:-
Note if the photometer units are set to fc the display will show .0000
7) Remove the light cover from the detector. The equipment is now ready
for use.
AVERAGE
When the light is unstable, press and release the MODE switch. The
photometer will now switch to manual ranging, Manual LED on, if not yet
previously in manual ranging. The Average LED will now switch on, but
the Units LED will remain unchanged.
To start an average sequence press and release the HOLD/RUN switch.
Immediately the display will show a fluctuating signal, reflecting the light
source fluctuations. After a short time the amplitude of the fluctuations
will decrease and the display will begin to show a reading which
represents the average light level during the period of the measurement.
At any time the averaging process can be halted by pressing the
HOLD/RUN button.
At any time the averaging sequence can be reset by pressing and
releasing the FUNCTION RESET switch.
If the light level fluctuations are large and any one reading causes the
detector amplifier to overload at this range the averaging process will be
terminated and the display will show:-
To avoid an overload conditions RESET the photometer and manually
change the RANGE to a lower lever. e.g. from a 34.00 range to 34.0.

Irradian Limited L203 Photometer
10


 (continued):


MIN & MAX LEVELS
During an average measurement sequence the maximum and minimum
values attained in the period are recorded. Press HOLD to halt the
averaging sequence. Press the MODE button to select between Average,
Min and Max. Note the Integrate display may overload and show - 0 L -.
It is also possible to view a MIN or MAX recording sequence by selecting
MIN or MAX prior to selecting RUN.
Press FUNCTION RESET to set the maximum and average values to
zero and the minimum to - 0 L -. Note the FUNCTION RESET will
operate during a measurement sequence or in the HOLD mode.
INTEGRATE
For measurements of the integrated dosage or exposure press the
MODE switch to select Integrate. Press the RUN switch to start the
measurement. The display will now autorange as the dosage increases.
Note the detector amplifier will not autorange and as with Average
measurements if the amplifier overloads the display will show - 0 L - and
the measurement will halt.
Units for integrated measurements are lux seconds (lux.s) footcandle
seconds (fc.s), cd.m
-2
.s and footLambert seconds (fL.s).
At the end of the integration period HOLD the display. Use the MODE
switch to also display the Min,Max and Average values.
Press FUNCTION RESET to set the integrate, maximum and average
values to zero and the minimum to - 0 L -. Note the FUNCTION RESET
will operate during a measurement sequence or in the HOLD mode.

L203 Photometer Irradian Limited
11 
      
            
      
(CIE Cos-112 filter ring fitted)
Illuminance is the measurement of photometric light per unit area,
lumens per metre, lux, or lumens per square foot, footcandle. For most
applications the measurement plane is horizontal and a cosine corrected
diffuser is fitted to the front of the detector assembly. If the working
surface is not horizontal then placing the detector on or parallel to the
worktop is a more representative measurement of the illuminance.
Note that all the light sources in the hemisphere above the detector will
contribute to the illuminance measurement. The sources may be
obvious, lamps or windows or even walls or other reflecting surfaces.
Take care not to shadow the detector during all illuminance
measurements.
1) Set up the photometer as outlined in section 3 with the illuminance
filter ring fitted and the units set to either lux or fc.
2) Place the detector at the measuring point and record the value on the
display. If the light levels are low it may be necessary to switch on the
display back light.
3) The display can be read directly for light levels from 0.0000 lux to 199
990 lux or 0.0000 to 19 999 fc. Note however that for illuminance
values of 20 000 to 199 990 lux, the x10 LED will illuminate and the
displayed value must be multiplied by 10.
CONVERSION FACTORS
1 lux = 0.0929 footcandle
1 lux = 1 candela @ 1 metre
1 lux = d² candela @ d metres

Irradian Limited L203 Photometer
12
      
            
      
(CIE FOV-112/101 probe fitted)
Luminance (lumens per steradian per unit area) or brightness is the
photometric measurement of the response from viewing an illuminated
object or self luminous source.
Distance d
Area A
Unit solid angle, steradian = A/d²
Uniform Source
Luminance can be expressed in candela (lumens per steradian) per unit
area, cd.m
-2
(also know as nit) or cd.cm
-2
or cd.ft
-2
.
Using the expression below, luminance, L, can be calculated by
measuring the illuminance, E, on a surface and knowing the reflectance,
ρ, of the surface.
L = ( E
*
ρ ) / πwhere πis expressed in steradians
= (x
*
ρ ) lm. m
-2
/ π
= (x
*
ρ / π) lm. str
-1
. m
-2
= (x
*
ρ / π) cd.m
-2
e.g.. Calculate the luminance of a surface with a diffuse reflectance of
ρ= 0.9 when illuminated at a level of 100 lux.
L = ( 100
*
0.9 / 3.14) cd.m
-2
= 28.7 cd.m
-2
Luminance can also be expressed as footLambert, fL. This unit
incorporates the πvalue and thus provides a simple relationship between
the illuminance of a surface of reflectance ρand the luminance of the
surface.
1 footLambert = 1
*
ρ footcandles

L203 Photometer Irradian Limited
13 
      
            
       (continued):
MEASURING LUMINANCE WITH THE L203 & THE FOV-CIE-112/101
Measuring luminance requires either the field of view probe and detector
/ filter combination to be pointed at a radiating surface or extended
source, or the CRT contact probe and detector / filter combination to be
in contact with a radiating surface or extended source. The field of view
probe will measure the average luminance within the area subtended by
its 6° field of view whereas the contact probe will average over the
contact area. For small area measurement with the field of view it will be
necessary to bring the probe close to the surface. Care must be taken
not to shadow the surface with the probe or yourself if the surface
luminance is produced by predominantly reflected light.
Luminance is independent of the measuring distance for a uniform
Lambertian infinite sized source, because the sampled area increase
cancels the inverse square law losses.
For luminance measurements of small areas it may be preferable to use
the Irradian Spot measuring Unit model SMU 203 as the reflex viewing
optics allows the user to determine the precise measurement area.
1) Set up the photometer as outlined in section 3 with either luminance
probe fitted and the units set to either cd.m
-2
or fL.
2) Point the detector at the reflecting surface or self luminous source or
press the contact probe squarely and firmly onto the surface and
record the value on the display.
3) The display can be read directly for all light levels from 0.0000* to 199
990 cd.m
-2
or fL (*with CIE-FOV-112 only). Note for luminance values
of 20 000 to 199 990 cd.m
-2
or fL, the x10 LED will illuminate and the
displayed value must be multiplied by 10.
CONVERSION FACTORS
1 cd.m
-2
= 0.292 footLamberts

Irradian Limited L203 Photometer
14
  
    
  


1) Switch off the photometer before changing the battery.
2) Slide open the battery compartment on the back of the photometer
and pull out the battery. Disconnect from the battery clip
3) Replace with a Lithium Manganese size PP3 9 volt battery.
4) Place battery inside compartment and slide cover closed.
5) Note it will be necessary to switch on and off the photometer before
normal operation will commence.

L203 Photometer Irradian Limited
15 
   
       
   


Photometry is the measurement of visible light. Irradian's photopic filter
and photodiode closely matches the response of the standard human
eye as published by the CIE (CIE Vλ). The spectral response of the
photodiode detector with the photopic filter ring is plotted beside the ideal
CIE response.
SD222 + CIE Cos-112
Relative Response
Figure 1
Photometers which do not closely match the response are often supplied
with correction factors for different types of lamps and light sources. This
means that the user has to identify the type of source being measured
and correct the meter reading. This procedure becomes more unreliable
when sources are mixed for example office lighting mixed with daylight
through a window.
The response of the Irradian photometer is such that the error for a wide
variety of sources is typically < 2%.

Irradian Limited L203 Photometer
16
!       
!       !       
!       


Illuminance is a measurement of visible light incident on a unit area
(Lumens/m²). A detector will measure this reliably when the light beam is
perpendicular to the detector's surface. Accurate measurements of
illuminance require that the detector should respond to light over a 180°
field of view. More importantly, this response should be proportional to
the cosine of the angle of light incident on the detector. To ensure that
the integration of light from all angles is correct, the cosine diffuser fitted
to the front of the filter ring is profiled such that the angular response of
the detector decreases with Cos(i) as the angle between the source and
detector increases from 0 to 90°.
CIE Cos-112
True Cosine Response
Figure 2
Irradian's cosine diffusers are corrected to match the cosine response to
within ± 3.5% up to angles of 75°. This ensures that the meter correctly
reads illuminance or visible light flux density whether it is measuring
scattered light (from an overcast sky) or a point source (a single lamp in
a dark room).