Islander ARMR2 User manual

Maintenance Manual
ARMR2

Major Components
Clicker Assembly
Dragknob
Crank
Spool
Retaining
Screw
Handle Assembly
BearingClutch Assembly
Pawl Assembly
Cam
Assembly
Foot
Frame
Draglever
Crank Assembly

General Information
Thank you for purchasing an Islander ARMR2 model mooching reel.
will help you identify, clean, and lubricate each important component to help keep your reel
performing like new.
Features of the ARMR2
• Handles stay stationary while the line is playing out.
• Full frame construction with one-piece spool and frame.
• Free spool operation controlled with frame-side recessed lever.
• One way large cork disc drag system.
• Face side adjustable drag knob.
• Islander classic outgoing clicker.
• A generous palming rim.
• Engraved serial number on spool and frame.
Technical Suppor t
Telephone [phone]
E-Mail [e-mail]

How To Disassemble Your Reel
1. Remove the retaining screw by turning
important that whichever tool you
small may damage the retaining screw.)
2. Remove the dragknob by turning it
counter-clockwise until it is loose.
Underneath the dragknob there will be a
nylon washer. It will either be stuck to the
bottomofthedragknobortothetopof
the dragspring.
3. Remove the crank by pulling it away from
the spool. Grasp the outside of the frame
withonehandandthespoolwiththe
other, and pull the frame and spool apart.
On the back of the spool you may notice
thattheclutchisstucktothebackofthe
spool. You can remove this by grasping
the teeth of the clutch and pulling.
Atthispointthereshouldbe8freeassemblies:RetainingScrew,Dragknob,
Dragknob Washer, Dragspring, Clutch, Crank, Spool, and Frame.
(B) Dragknob Figure 1
(A)RetainingScrew (C)Crank

Cleaning and Lubricating Your Reel
1. Disassemble your reel as shown above.
2. Remove the clutch assembly [1] .
3. Clean the clutch assembly. Remove old grease and
grit using a soft cloth.
4. Clean the base of the spindle, [2]. Remove any old
grease and grit from using a soft cloth.
5. Clean the pawl/cam assembly [A] and [B]. Remove
any old oil and grit using a brush or swab.
6. Oil and grease all indicated locations.
7. After lubrication, work the Draglever [3] back
a forth a few times to work the lubrication
through the cam and pawl assemblies.
8. With the Draglever [3] in the “disengaged”
position, lower the clutch back into position,
cork side up. Re-engage the Draglever [3] .
A) Oil Pawl
B) Oil Cam
C) Grease
Cam
2) Spindle
1) Clutch
Assembly
Figure 2
Figure 3
F) Grease Bearing
Under Clutch
3) Draglever
D) Grease
Teeth of
Clutch
E) Oil Clutch
Cork
Your reel comes from the factory lubricated. Periodic lubrication is recommended to maintain
optimum performance.

F) Oil Clicker
Assembly
Figure 4 Figure 5 - Drag Spring
G) Grease Bearings
(front of spool and
rear of spool)
Figure 6 -
Handle Assembly
9. Remove old oil from the around the clicker
assembly using a brush or swab.
10. Remove old grease from the surface of
the bearings. One bearing is located at [G],
while the other bearing is on the other side
of the spool. If the dragspring [Figure 5] has
not been removed, please do so to clean
and lubricate this bearing.
11. The crank requires a small amount of
dragspring does not require any lubrication.
Just wipe the dragspring o
with a soft cloth.
12. The handle assembly need not be lubricated. Simply remove the screw holding the
Because of the conditions that this style of reel is used under (saltwater), it is important
that the reel be rinsed o under a warm water stream after each trip. While the reel is saltwater safe,
the quick rinse will help your reel perform better in the long run. Avoid immersing the spool in water,
because moisture will be retained by the backing.

Tuning
It is possible to tune both incoming and outgoing
clicks, to a certain extent. For these adjustments,
you will need to disassemble your reel.
outgoing click, push the clicker spring [2] in the
direction indicated by [B], Figure 7. Do not push
spring more than a few degrees, as pushing too
far will remove the outgoing click altogether.
incoming click, push the pawl spring [4] in the
direction indicated by [C], Figure 8.
incoming click, push the pawl spring [4] in the
direction indicated by [D], Figure 8. Do not push
this spring more than a degree.
Figure 8
C) For louder
incomming click
4) Pawl Spring
3) Pawl D) For a quieter
incoming click
1) Clicker
A) For a louder
outgoing click
Figure 7
2) Clicker Spring
B) For a quieter
outgoing click
the outgoing click, push the clicker spring
in the direction indicated by [A], Figure
7. Push the spring until the clicker [1] is
pointing directly at the bearing on the
rear of the spool.

Copyright © 2017 Islander Precision Reels. All Rights Reserved.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are
[e-mail] | www.islander.com
Reel Maintenance Kit
Use the same lubricant as the pros! A well lubricated and clean reel will last you a lifetime. We recommend
Islander’s Reel Maintenance Kit. It comes with all the lubricants you need for your ARMR2 reel.
Oil: Super Lube® Multi-Purpose Synthetic-based Oil with PTFE®
Grease:
Contact your local dealer or visit www.islander.com.