Islander Steelheader Operating and maintenance instructions

Maintenance Instructions
For IS Float Reels
IS
For parts and service
call toll free: 1-888-404-1119
www.mikesreelrepair.com

Thank you for purchasing an Islander Steelheader model float reel.
In this manual you will find information on how to take are of your new
reel. Concise illustrations will help you identify, clean, and lubricate
each important component to keep your reel performing like new.
Features of the Islander Steelheader
Smooth sealed stainless steel bearings.
Simple clicker drag system to help reduce line overruns.
Free spool operation controlled by a frame-side button.
Full frame construction with one piece spool and frame.
Suitable for both right and left hand retrieve.
Generous palming rim.
Engraved serial number on the frame.








Figure 2 - Clicker Button
4) Push back
and down to
disengage.
5) Push up
to engage
How to Disassemble/Reassemble Your Reel
Remove the spindle screw (2) by turning it counter-
clockwise, using a snug-fitting screw driver or coin.
(It is important that you choose a tool that fits well,
as one that is too small may damage the spindle
screw.)
Once the screw is removed, you may notice that
there is a captive rubber O-ring on the underside
of the spindle screw (2). There is no need to
remove this O-ring, and it will not fall out on its own.
Grasp the outside of the frame (3) with one hand
and the spool (1) with the other, and pull the frame
and the spool apart.
Figure 1
2) Spindle
Screw
1) Spool 3) Frame
At this point, there should be 3 free assemblies:
Spindle Screw (2), Spool (1), and the Frame (3).
1.
2.
3.
Reassembly is the opposite of disassembly. To make spool
to frame assembly a little easier, it is a good idea to
disengage the clicker, as illustrated on Figure 2.
Note: Do not overtighten the spindle screw (2). Tighten the
screw just until it meets resistance.
4.
5.
For parts and service
call toll free: 1-888-404-1119
www.mikesreelrepair.com

4.
5.
6.
Cleaning and Lubricating Your reel comes lubricated from the factory .
Periodic lubrication is recommend to maintain
optimum performance.
Figure 4
5) Clicker
Button
D) Oil
Under
Button
Figure 3
3) Spindle
A) Grease
Spindle
B) Oil
Spring
C) Oil &
Grease
Clicker
2) Clicker
1) Clicker
Spring
4) Frame
Disassemble your reel as per instructions on Page 2
of this manual.
Clean the spindle (3) using a soft cloth, to remove
the old grease and grit that has accumulated there.
Clean around the clicker (2) and spring (3). You
may have to use a small, soft brush to remove
the old oil, grease, and grit from this location.
1.
2.
3.
Clean the inside of the frame (4) with a soft
cloth to remove any contaminants which
may have collected.
Oil and grease all of the indicated locations.
When greasing the spindle (3 and A), all
that is required is an amount of grease
similar in size to a teardrop.
After lubrication, work the clicker button (5)
back and forth a few times to work the
lubrication through the button and clicker
assemblies
For parts and service
call toll free: 1-888-404-1119
www.mikesreelrepair.com

This level of cleaning and lubrication should be carried out once every 3-4 fishing trips. Because of the
conditions that this style of reel is used under (saltwater and freshwater), it is important that the reel be
rinsed off under a warm water stream after each trip. While the reel is saltwater safe, the quick rinse will
help your reel perform better in the long run. Avoid immersing the spool in water if there is backing/line
present. Moisture will be retained by the line.
E) Grease
Teeth Of
Gear
Figure 5
6) Gear
7) Bearing
8) Spool
F) Grease bearing
opposite to the one
shown.
Remove all the old grease from the gear (6). You
may have to use a toothbrush or similar implement
to accomplish this.
Clean the bearings (7 - there is another identical
bearing opposite to the one shown) with a soft cloth
to remove all the old grease and grit that has
accumulated there.
Clean inside the spool cavity (8) with a soft cloth to
remove any contaminant which may have collected.
Oil and grease all of the indicated locations. You
are only required to grease the bearing opposite to
the bearing (7) that is shown. This bearing (7) will
become lubricated when it comes in contact with
the spindle.
The spindle screw, Figure 6, does not require any
lubrication. It only requires that its O-Ring (found
underneath the head of the screw) be cleaned.
The handle assembly, Figure 7, does not have to
be lubricated. Simply remove the screw holding
the handle with a flat bladed screw driver and clean
thoroughly by wiping down the base with a soft cloth
and running a cotton swab through the handle.
7.
8.
9.
10.
11.
12.
Figure 6 -
Spindle Screw
Figure 7 -
Handle Assembly
For parts and service
call toll free: 1-888-404-1119
www.mikesreelrepair.com

Tuning
It is possible to tune the intensity of the reels' click, to
a certain extent. For these adjustments, you will need
to disassemble your reel.
If you find that your reel is too quiet when the click-drag is
engaged, push the clicker spring (1) in the direction indicated
by the arrow marked (A) For a louder click.
If you find that your reel is too loud when the click-drag is
engaged, push the clicker spring (1) in the direction indicated
by the arrow marked (B) For a softer click.
A) For a louder click
B) For a softer click
1) Clicker Spring
1.
2.
Troubleshooting
If you find that your handles are stiff, remove the handles as per instructions on page 4 (Cleaning and
Lubricating Your Reel), and clean them. Most poor turning handles are cause by a collection of grit that
accumulates between the handle and the handle base.
If you find that your reel is too loud or quiet, tune the reel as per the instructions above.
If you find that your clicker button does not engage or disengage properly, clean and oil around the clicker
and button assemblies as referenced on page 3 (Cleaning and Lubricating Your Reel)
1.
2.
3.
For parts and service
call toll free: 1-888-404-1119
www.mikesreelrepair.com

Clicker Assembly
Major Components
Gear
Bearing
Foot
Handle
Assembly
Spool
Spindle
Screw
Clicker
Button
Frame
For parts and service
call toll free: 1-888-404-1119
www.mikesreelrepair.com

Product Information
Recommended Adhesives
Islander recommends the use of Loctite® 262 Permanent Threadlocker and
Loctite® 242 RemovableThreadlocker. Loctite® 262 and Loctite® 242 are
registered trademarks of Loctite Corp., U.S.A.©
If you have any questions or comments about your reel, please phone,
fax, or e-mail Islander Reels. If Islander Reels requests that your reel
be sent in for repair, please remove the line from your reel.
Islander Reels
6771 Kirkpatrick Crescent
Saanichton B.C. V8M 1Z8
Canada
Phone [phone]
Fax [phone]
Email [e-mail]
Site www.islander.com
Recommended Lubricants
Islander recommends the use of Super Lube® brand oil and grease with
Teflon® for all lubricating applications. Super Lube® is manufactured by:
Synco Chemical Corp., N.Y. Teflon® is a registered trademark of E.I.
duPont DeNemours & Co.
Oil: Super Lube® Multi-Purpose Synthetic-based Oil with PTFE®
Grease:Super Lube® Multi-Purpose Synthetic-based Grease with PTFE®