ISOIL MS501 User manual

INSTRUCTION MANUAL
MS501

INDEX
START UP AND MAINTENANCE OF THE INSTRUMENTS _____________ 1
INTRODUCTION___________________________________________ 1
SAFETY__________________________________________________ 2
GENERAL INFORMATION ON THE SENSORS INSTALLATION _________ 2
OVERALL DIMENSIONS _____________________________________ 4
GROUNDING INSTRUCTIONS _______________________________ 10
OPERATIVE TEMPERATURE _________________________________ 10

1
SENSOR FOR ELECTROMAGNETIC FLOW METER – MANUAL
INTRODUCTION
– This manual is integral part of the product. Read carefully the instructions contained since
it contains important indications for the safety of use and of maintenance.
– The technical information and the relative products of this manual could be modied
without any previous notice.
– The ow meter must be used for the use it has been built for. The improper use, possible
tampering of the instrument or parts of it and substitutions of any components not original,
makes the warranty to decay automatically.
– The manufacturer is considered responsible only if the instrument is used in its original
conguration and setting.
– The owmeter makes measures of liquids with conductivity greater than 5µS/cm; it consists
of a sensor (described in this manual) and a converter, for it see the manual provided.
– If the sensor is supplied in compact version to the converter, consider the operating
temperatures more restrictive, otherwise refer to the respective manuals (page 10).
– When transporting, unpacking and handling the owmeter, be careful and care.
– In the case of prolonged storage and of transport, use and store in the original container
in a dry place, do not place more than 3 packs one above the other.
– It is possible pallets storage and transport (in case of wooden crates do not place one
above the other).
– For the cleaning of the device use only a damp cloth, and for the maintenance/repairs,
contact the customer service.
– For the disposal of the device and of the packaging make strict reference to the regulations
– It is forbidden the reproduction of the present manual and of possible software supplied
with the instrument.
START UP AND MAINTENANCE OF THE INSTRUMENTS
– Before starting up the instrument, always make a sure connection to ground as suitable
to page 10.
– Verify periodically: the cables integrity, the tightening of the sealing elements (cable glands,
covers, etc.), the mechanical xing of the instrument on the pipe or on the wall stand

2
SENSOR FOR ELECTROMAGNETIC FLOW METER – MANUAL
Before using the instrument, always make a sure connection to the ground
Avoid any attempt to repair the instrument. If the instrument is not
functioning properly, please call the nearest assistance service
Pay maximum attention during the operations
ATTENTION !!!
DANGER !!!
SAFETY
GENERAL INFORMATION ON THE SENSORS INSTALLATION
Before install the sensor locate the direction of the liquid in the piping
The sign of the ow rate is positive, when the ow direction is from – to + as printed on the
tag plate.
If after the installation, for plant request becomes necessary reverse the sign of the ow, it is
enough reverse the sign of the coefcient KA
Flow direction
?
-+

3
SENSOR FOR ELECTROMAGNETIC FLOW METER – MANUAL
ANTIVIBRATION
3 X DN
2 X DN
LONGPIPE
FITTINGSENSOR
FITTINGPIPE
NUT
FITTINGSENSOR
FITTINGPIPE
NUT
Install the sensor away from bends and hydraulic accessories
Avoid positioning fittings by tigthening the clamps.
In vertical installations an ascending flow is preferable. For vertical installations with descending flow
direction contact the manufacturer
For installations in long pipe lines, please use anti vibration joints
Avoid a partially empty pipe, during operation the pipe must be either completely full of liquid or
completely empty

4
SENSOR FOR ELECTROMAGNETIC FLOW METER – MANUAL
OVERALL DIMENSIONS
gas/npt without lining
70 (2.76")
25 (1")
FITTINGS
FITTINGS
128 (5.04)
80 (3.15")
76 (3")
170 (6.7")
CONNECTIONS GAS/NPT (STAINLESS STEEL WITHOUT LINING)
DIMENSIONS mm (inches) DN
3 (1/8") 6 (1/4) 10 (3/8) 15 (1/2") 20 (3/4")
FITTINGS 1/4" 3/8" 1/2" 3/4" 1"

5
SENSOR FOR ELECTROMAGNETIC FLOW METER – MANUAL
overall dimensions gas/npt with lining
70 (2.76")
25 (1")
FITTINGS
FITTINGS
128 (5.04)
80 (3.15")
76 (3")
170 (6.7")
CONNECTIONS GAS/NPT (WITH LINING)
DIMENSIONS mm (inches) DN
3 (1/8") 6 (1/4) 10 (3/8) 15 (1/2") 20 (3/4")
FITTINGS 1/2" 1/2" 3/4" 1" 1"1/4

6
SENSOR FOR ELECTROMAGNETIC FLOW METER – MANUAL
overall dimensions Flanged without lining
FLANGE CONNECTIONS UNI (STAINLESS STEEL WITHOUT LINING)
DIMENSIONS mm (inches) DN
3 (1/8") 6 (1/4) 10 (3/8) 15 (1/2") 20 (3/4")
D90 (3.54) 90 (3.54) 90 (3.54) 95 (3.74) 105 (4.13)
H183 (7.20) 183 (7.20) 183 (7.20) 186 (7.30) 191 (7.5)
FITTINGS DN 10 DN 10 DN 10 DN 15 DN 20
FITTINGS
FITTINGS
D
H
80 (3.15")
200 (7.87)
70 (2.76")
25 (1")
FLANGE CONNECTIONS ANSI (STAINLESS STEEL WITHOUT LINING)
DIMENSIONS mm (inches) DN
3 (1/8") 6 (1/4) 10 (3/8) 15 (1/2") 20 (3/4")
D88.9 (3.5) 88.9 (3.5) 88.9 (3.5) 88.9 (3.5) 98.4 (3.87)
H183 (7.20) 183 (7.20) 183 (7.20) 183 (7.20) 188 (7.37)
FITTINGS 1/2" 1/2" 1/2" 1/2" 3/4"

7
SENSOR FOR ELECTROMAGNETIC FLOW METER – MANUAL
overall dimensions Flanged with lining
FLANGE CONNECTIONS UNI (PTFE LINING)
DIMENSIONS mm (inches) DN
3 (1/8") 6 (1/4) 10 (3/8) 15 (1/2") 20 (3/4")
D90 (3.54) 90 (3.54) 90 (3.54) 95 (3.74) 105 (4.13)
H183 (7.20) 183 (7.20) 183 (7.20) 186 (7.30) 191 (7.5)
FITTINGS DN 10 DN 10 DN 10 DN 15 DN 20
FITTINGS
FITTINGS
D
H
80 (3.15")
200 (7.87)
70 (2.76")
25 (1")
FLANGE CONNECTIONS ANSI (PTFE LINING)
DIMENSIONS mm (inches) DN
3 (1/8") 6 (1/4) 10 (3/8) 15 (1/2") 20 (3/4")
D88.9 (3.5) 88.9 (3.5) 88.9 (3.5) 88.9 (3.5) 98.4 (3.87)
H183 (7.20) 183 (7.20) 183 (7.20) 183 (7.20) 188 (7.37)
FITTINGS 1/2" 1/2" 1/2" 1/2" 3/4"

8
SENSOR FOR ELECTROMAGNETIC FLOW METER – MANUAL
overall dimensions sanitary clamp connections
80 (3.15")
128 (5.04")
76 (3")
70 (2.76")
25 (1")
FITTINGS
FITTINGS
F
170 (6.7")
I
CLAMP ISO 2852
DIMENSIONS mm (inches) DN
3 (1/8") 6 (1/4) 10 (3/8) 15 (1/2") 20 (3/4")
I12.7(0.5) 12.7(0.5) 12.7(0.5) 17.2(0.68) 21.3 (0.84)
F34 (1.34) 34 (1.34) 34 (1.34) 34 (1.34) 34 (1.34)
CLAMP ISO 2852
DIMENSIONS mm (inches) DN
3 (1/8") 6 (1/4) 10 (3/8) 15 (1/2") 20 (3/4")
I9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 15.85 (0.62) 22.2 (0.87)
F25.4 (1) 25.4 (1) 25.4 (1) 25.4 (1) 50.5 (1.99)

9
SENSOR FOR ELECTROMAGNETIC FLOW METER – MANUAL
80 (3.15")
128 (5.04")
76 (3")
70 (2.76")
25 (1")
FITTINGS
FITTINGS
170 (6.7")
overall dimensions sanitary din/sms
DIN 11851
DIMENSIONS mm (inches) DN
3 (1/8") 6 (1/4) 10 (3/8) 15 (1/2") 20 (3/4")
FITTINGS DN 10 DN 10 DN 10 DN 15 DN 20
SMS 1146
DIMENSIONS mm (inches) DN
10 (3/8) 15 (1/2") 20 (3/4")
FITTINGS DN 25 DN 25 DN 25

10
SENSOR FOR ELECTROMAGNETIC FLOW METER – MANUAL
GROUNDING INSTRUCTIONS
OPERATIVE TEMPERATURE
For correct operation of the meter is NECESSARY that the sensor and the liquid are equipotential,
so ALWAYS connect the sensor and converter to ground:
VERSION
LIQUID TEMPERATURE AMBIENT
TEMPERATURE
OTHER
CONVERTERS ML-4F1
COMPACT -20°C ÷ 100°C
-4°F ÷ 212°F
-20°C ÷ 130°C
-4°F ÷ 266°F -10 °C ÷ 60 °C
14°F ÷ 140°F
SEPARATE -20°C ÷ 130°C
-4°F ÷ 266°F

11
SENSOR FOR ELECTROMAGNETIC FLOW METER – MANUAL

12
SENSOR FOR ELECTROMAGNETIC FLOW METER – MANUAL

13
SENSOR FOR ELECTROMAGNETIC FLOW METER – MANUAL

SENSOR FOR ELECTROMAGNETIC FLOW METER – MANUAL