ISON IS-DH310P-2F-8 User manual

1
Quick Installation Guide
IS-DH310P-2F-8
Industrial 10 port POE switch, with 8 x 10/100M TX PSE (802.3af/at) + 2 Giga SFP
IS-DH310P-8
Industrial 10 port POE switch, with 8 x 10/100M TX PSE (802.3af/at) + 2 Giga TX
FCC MARKING
This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at the own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference.
(2) this device must accept any interference received; including interference that may cause undesired
operation.
CE MARKING
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class A
for ITE, the essential protection requirement of Council Directive 2004/108/EC on the approximation of the
laws of the Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information in this
document is not up-to-date. Please check with your local distributors for the latest information. No part of
this document can be copied or reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.

2
Copyright © 2016, PRIMMCON Industries Inc. All Rights Reserved.

3
Introduction
This rugged design Industrial 10 port POE switch, complied with IEEE802.3af and IEEE802.3at, and pass
many rigorous environmental test. It delivers 30 watts (Max 36 watts) power per POE port, also generate up
to 200 watts power to PD devices. The uplink 2 SFP port can extend to a wilder area connection. With its
multi-purpose design, that can also be used for Din-Rail or wall-mounted. This is an ideal unit for IP
surveillance, traffic monitoring and security application in critical environment which -40°C to 75°C range is
required.
Housing Dimension (IS-DH310P-2F-8) (mm)

4

5
Housing Dimension (IS-DH310P-8) (mm)

6
Installation package (the mounting kit)
This product can be installed by din-rail mounted or wall-mounted. Din-rail brackets and wall-mounted
bracket are included.
Power Input connection
This product provides 6 pin terminal block. The POE port can be operated from 48-56VDC power source.
The VDC power range can be 48VDC only or lower, or wide range from 48-56VDC. Please always to make
sure your input voltage is the supported voltage range for each model.
WARNING –Any exceeded input voltage will not make this product function properly and may
damage it.
To make power connection –
This unit can receive 3 power inputs. PW1, PW2, and PW3, Follow the printed polarity for V1+, V1-, V2+,
V2-, and ground. Connect positive wire to V+, connect negative wire to V-, and also connect neutral wire to
the ground screw as shown.
Relay –This relay function monitor Power failure. You may use 24V@1A relay connection to your external
alarm device to monitor power status. Relay function will only work with PW1 and PW2. When PW1 and
PW2 are connected, the relay is in “OPEN”mode. The LED RLY indicator will goes OFF. When only PW1 or
PW2 is connected, the relay is in “SHORT”mode. The LED RLY indicator will goes “ON”
6 pin Terminal Block x1
Din Rail Bracket x 1
Wall mount bracket x 2

7
Power connecting procedure:
STEP 1 –Pull out 6 pin terminal block.
STEP 2 –Connect wire to V1+, V1-, or V2+, V2-, and Ground the neutral wire to the ground screw.
STEP 3–Plug back 6 pin terminal block to its place.
For PW3 connection --- Use an external industrial graded power adapter to make proper connection. Follow
the priority sign V+, V-.
WARNING –
Always ground the power source to remain a clean power input. Too many LOW-END power supplies
produce too much noise which can produce POE detection failure. To avoid this, always ground the
power source to gain a clean power input.

8
LED indicator (IS-DH310P-2F-8)
P3, P4, P5, P6, P7, P8, P9, P10 (Green)
ON—PD is detected on designated
port.
OFF –no PD is detected
Port 3 to 10
SPD (Amber)
ON –100M speed is detected.
OFF –10M speed is detected
Port 1 (Green)
ON –port 9 SFP fiber is detected
OFF –port 9 SFP fiber is not detected.
Flashing –port 9 SFP fiber is active
Port 2 (Green)
ON –port 10 SFP fiber is detected
OFF –port 10 SFP fiber is not detected.
Flashing –port 10 SFP fiber is active
P1 (Green)
ON -- when V1+, V1- is connected
P2 (Green)
ON -- when V2+, V2- is connected
P3 (Amber)
ON –when V3+, V3- is connected
ALM (Amber)
ON—PW1 or PW2 is connected
OFF—PW1 & PW2 are connected
Port 3 to 10
LNK (Green)
ON—TX link is detected
OFF –TX port is not detected
Flashing –TX port is active

9
LED indicator (IS-DH310P-8)
P3, P4, P5, P6, P7, P8, P9, P10 (Green)
ON—PD is detected on designated
port.
OFF –no PD is detected
Port 3 to 10
SPD (Amber)
ON –100M speed is detected.
OFF –10M speed is detected
P1 (Green)
ON -- when V1+, V1- is connected
P2 (Green)
ON -- when V2+, V2- is connected
P3 (Amber)
ON –when V3+, V3- is connected
ALM (Amber)
ON—PW1 or PW2 is connected
OFF—PW1 & PW2 are connected
Port 3 to 10
LNK (Green)
ON—TX link is detected
OFF –TX port is not detected
Flashing –TX port is active
Port 1, 2
SPD (Amber)
ON –1000M speed is detected.
OFF –100M or 10M speed is detected
Port 1, 2
LNK (Green)
ON—TX link is detected
OFF –TX port is not detected
Flashing –TX port is active
10

10
Technical Specification:
IEEE Standard
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3z 1000Base-X fiber
IEEE802.3x Flow Control and Back Pressure,
IEEE802.3af for POE
IEEE802.3at for POE+
Switch Architecture
Back-plane (Switching Fabric): 5.6Gbps
Data Processing
Store and Forward
MAC address Table Size
8K
Packet Buffer Size
1M
Network Connector :
8xRJ-45 10/100BaseT(X) auto negotiation,
8 10/100M POE+ 802.3at/af PSE port,
2 x 1000M SFP (IS-DH310P-2F-8)
2xRJ-45 10/100/1000BaseT(X) auto
negotiation(IS-DH310P-8)
Auto MDI/MDI-X function, Full/Half duplex
Network Cable
UTP/STP Cat.5e or above Cable
EIA/TIA-568 10-ohm (100m)
Protocol
CSMA/CD
LEDs
PW1(Power 1) Green,
PW2(Power 2) Green,
PW3(Power 3) Amber for External Power adapter
RLY (Relay) Amber
F9 ( SFP) Green/Link, Flash/active
F10 (SFP) Green/Link, Flash/active
TX/RJ-45 port:
Green --- LNK (Link/Active)
Amber --- 100M
Fiber port
F9 ( SFP) Green/Link, Flash/active
F10 (SFP) Green/Link, Flash/active
POE
Green POE detected
Console Green -- console connection detected