ISON IS-DG306P Series User manual

1
FCC MARKING
This Equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received; including interference
that may cause undesired operation.
CE MARKING
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55022 class A for ITE, the essential protection requirement of
Council Directive 2004/108/EC on the approximation of the laws of the Member
States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date. Please check with
your local distributors for the latest information. No part of this document can be
copied or reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective
companies.
Copyright © 2013, All Rights Reserved.
IS-DG306P Series
Quick Installation Guide

2
Introduction
This rugged designed Industrial Ethernet switch / Industrial Giga -bit 4 port POE Injectors, comply with
IEEE802.3af and IEEE802.3at, has pass many rigorous environmental test. It delivers 30watts ( Max
36watts) power per POE port. And it can generate total 126 watts power to PD devices. the u plink 2 SFP
port can extend your environment to a much larger area.With its multi-purpose design, it can also be used
for Din-Rail or wall-mounted. It is an ideal unit for IP surveillance, traffic monitoring and Security
application in critical environment. It can tolerate -40°C to 75°C in harsh environment to perform a reliable
network.
Housing Dimension

3
MODELS –Industrial Giga-bit POE 4 port Injector, 48VDC input
This industrial high power POE+ is designed for multiple applications, especially for vehicle surveillance,
IP surveillance, and traffic monitoring and for a broad range of outdoor applications. It can be used as a
stand-alone device for buses, trucks for Surveillance purposes. And it also can be used to
cascaded/daisy-chain to other devices to cover wider area through the SFP connection.

4
Power connection
This unit provides 6 pin terminal block. The POE port can be operated from 44-56VDC power source. The
VDC power range can be 48VDC only or lower, or wide range from 44-56VDC. Always Make sure your input
voltage is within this supported voltage range for each model.
WARNING – any exceeded input voltage will not make this unit function and may damage this unit.
To make power connection – Follow the printed polarity for V1+, V1-,
V2+, V2-, and ground. Connect positive wire to V+ , connect negative
wire to V-, also connect neutral wire to the ground screw as shown .
Relay -- You may use 24V@1A relay connection to your external device
for special purpose. When 2 powers are connected, the relay is in
SHORT mode. When any power source fails, the relay change to OPEN
status.
Power connecting procedure:
STEP 1 – Pull out 6 pin terminal block.
STEP 2 – Connect wire to V1+, V1-, or V2+, V2-, and Ground the neutral wire to the ground screw.
STEP 3– Plug back 6 pin terminal block to its place.
WARNING –
Always ground the power source to maintain a clean power input. Due to too many cheap
made power supplies, it creates too much noise, and it will cause the power input fluctuates
when connect to this unit. To avoid this, always ground the power source to gain a clean
power input.
Din Rail Bracket x 1
Wall mount bracket x 2
6 pin Terminal Block x1
Installation package
This unit can be installed by din-rail mounted or wall-mounted. Din-rail brackets and wall-mounted
bracket are included.

5
Dip switch function
Amber LED
ON – 1000M speed is detected.
OFF – 10M or 100M speed is detected
P1
ON -- when V1+, V1- is connected
1
ON – port 1 SFP fiber is detected
OFF – port 1 SFP fiber is not detected.
Flashing – port 6 SFP fiber is active
Green LED
ON—TX link is detected
OFF – TX port is not detected
Flashing – TX port is active
LED indicator
This unit is equipped with dip switches, located on the front panel. Adjusting the dip switches will
change the default function of this unit. This unit has set to manufacturer default as: Port 5 SFP and the
speed is set to 1000M for both port 5 and port 6 SFP ports. you may adjust dip switch setting to select
port 5 as TX ( disable port 5 SFP) or set SFP speed to 100M. The detail setting as shown below:
P2
ON -- when V2+, V2- is connected
ALM
ON –
Only PW1 or PW2 is connected..
OFF-
Both PW1 and PW2 are connected
2
ON – port 2 SFP fiber is detected
OFF –port 2 SFP fiber is not detected.
Flashing – port 5 SFP fiber is active
3,4,5,6
ON—PD is detected on designated
port.
OFF – no PD is detected

6
Specification:
IEEE Standard
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3z 1000Base-X Gigabit Ethernet
IEEE802.3x Flow Control and Back Pressure,
IEEE802.3af for POE
IEEE802.3at for POE+
Switch Architecture
Back-plane (Switching Fabric): 12Gbps
Data Processing
Store and Forward
Flow Control:
IEEE 802.3x Flow Control and Back Pressure
Jumbo Frame
9KB
MAC address Table Size
1K
Packet Buffer Size
1Mbits
Network Connector :
5xRJ-45 10/100/1000BaseT(X) auto negotiation,
4 Giga POE+ 802.3at/af PSE port
Auto MDI/MDI-X function, Full/Half duplex
2 x SFP 100/1000M BaseX
Network Cable
UTP/STP above Cat.5e Cable
EIA/TIA-568 100-ohm (100m)
Fiber Cable (Multi-mode):50/125um,62.5/125um
Fiber Cable (Single-mode): 9/125um
Protocol
CSMA/CD
LED
P1(Power 1) Green,
P2(Power 2) Green,
ERR( Fault ) Amber,
TX/RJ-45 port:
LNK (Link/Active) Green,
SPD(Speed) 10/100(OFF ) ,1000 (Green)
SFP Fiber Per port:
Link (Green)
Active Flash
Reserve polarity protection
Present
Overload current protection
Present
Power Supply
Redundant Dual DC 9V-56V Power Input without POE
Power Consumption
5.76W@12/24/48 VDC full load, Without POE

7
Alarm Relay Contact
Relay outputs with current carrying capacity of 1 A @24VDC,
Relay in short circuit mode when 2 powers are connected. in
open circuit mode when only one power supply is connected
Ethernet Switch power input
Ethernet switch power input 9VDC -56VDC
POE power
input Voltage 44VDC-56VDC.
POE power per port 30watts. Maximum 36Watts
Maximum total power 126Watts
Removable Terminal Block
Provide 2 Redundant power , Alarm relay contact ,6 Pin
Wire range: 0.34mm^2 to 2.5mm^2
Solid wire (AWG):12-24/14-22
Stranded wire(AWG): 12-24/14-22
Torque:5lb-In/0.5Nm/0.56Nm
Wire Strip length: 7-8mm
Operating Temperature
-40℃~75℃ fully tested.
Operating Humidity
5% to 95% (Non-condensing)
Storage Temperature
-40℃~85℃
Housing
Rugged Metal ,IP30 Protection
Case Dimension (W X D X H)
142mmx43mmx105mm (LxWxD)
Installation mounting
DIN Rail mounting and Wall Mounting
EMC/EMS
CE, FCC,VCCI
EMI
FCC Part 15 Subpart B Class A,
CE EN 55022 Class A