Itotec ROBOCUT eRC-1150DX User manual

Paper Cutter
Type No.
Operation Manual for Paper Cutter
Carefully read through this operation manual and be familiar with the description before
starting operation, inspection or maintenance of the product.
The operator or administrator of this product may not have the product operated by a
person who is not familiar with the description about the product.

2
Foreword
Safety precautions
Warning label
Front view
Rear view
Operation panel
Memory mode screen
Manual mode screen
Automatic mode screen
Operation panel of main body
Left/right adjustment of backgauge 1
Left/right adjustment of backgauge 2
Vertical adjustment of backgauge 1
Vertical adjustment of backgauge 2
Setting the clamp pressure (main pressure)
Checking the knife height
Fine adjustment of knife height
How to determine the knife angle
Knife type
How to change the cutting stick
How to replace the safety bolts
How to install the false clamp
Introduction
Name and function of each part
4
5
6
8
9
10
12
14
15
16
18
19
20
21
22
23
24
25
25
26
27
28
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
How to adjust
Getting started
How to operate the cutting button
How to operate the backgauge
How to change the backgauge speed
How to change the unit
Correction of error between actual size
and displayed size (zero point correction)
How to call up a course
How to call up unused course
How to delete a course
How to call up a page
How to insert a page
How to delete a page
How to use the cut line unit
How to use the air table
How to reset the paper cutting counter
How to reset the knife change counter
How to look at the alarm history
How to operate
Table of Contents

3
How to change the unit of the course
How to store data (ten-key pad storage method)
How to store data (current size storage method)
How to store data (storing data while cutting)
How to adjust push-out
How to set the common push-out setting
How to adjust stacking position
How to adjust the pedal pressure
How to adjust the clamp pressure
How to set clamp hold
How to adjust the clamp hold timer
How to set the clock
Function selection method
How to adjust the knife change counter
How to congure paper cutting functions
How to adjust the backgauge acceleration
How to adjust the periodic inspection timing
How to adjust the oil replacement timing
Pedal pressure adjustment
Data monitor
How to set the language
How to lock data
How to use free memo
How to enter the job name and memo
How to store data and set
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
89
92
94
96
97
98
99
100
101
How to start full automatic operation
How to specify the repeat size or number of
repeat size
How to clamp
How to enter the repeat size of clamping
How to copy a page
How to use the calculation function
How to repeat advance
How to use the edit history
How to display the course list
How to copy or move a course
How to display details of course
How to search for a job name or memo
How to use the search history and preset
How to use the calendar
How to remove the knife
How to install the knife
How to remove the knife (Knife lifter)
How to install the knife (Knife lifter)
Replacement of hydraulic oil
Replacement of gear oil
Lubrication and greasing
Oil table
Repair Service
Specications
Application operations
How to change the knife
How to change oil
Repair Service & Specications
Table of Contents

4
Introduction
Foreword
WARNING
Inadvertent operation of the machine will cause serious injuries or
disasters.
Read through this manual before starting operation or maintenance of this machine.
Keep this manual near the machine so that you can refer to it at any time.
Do not start operation or maintenance of the machine until you are familiar with the
description given in this manual.
Order this manual to us or our agency without delay if it is lost or damaged.
When handing over this product, be sure to attach this manual to the next owner, too.
●
●
●
●
This manual gives guidance about safe operation of this product.
Be sure to read through this manual and be familiar with the operation, inspection and
maintenance procedures before starting operation of the product.
Operation procedures different from those described in this manual may cause serious
accidents.
The precaution specified below is given in various parts of this manual. The indication
gives precautions for safety assurance. Fully understand the description when working.

5
●Operating environment of this machine
Paper and other materials may be stacked around the machine. Securely stack and take measures to
avoid tripping over or colliding against them.
Do not place the machine at a place susceptible to rainwater or in high humidity. Do not operate the
machine in a wet state.
Do not operate the machine near ammable liquid or gases.
Keep infants and children away from the machine.
Extremely high accuracy is required for paper cutting work together with the safety of the work. Provide the
work site with adequate lighting measures that is free from icker or glare.
Paper powder scatters during work. You must also pay attention for ventilation and natural wind.
●Transportation and installation
Our product is transported by professional workers contracted by us. Our service personnel conduct
installation. Have electric work done by a qualied electrician.
For the electric capacitance, look at the specications.
Contact our service personnel when moving our product.
●Repair services
If a fault is caused to the machine, contact our service personnel. Do not operate the machine until the fault is
removed.
Safety precautions
The warning indication is classied into the following categories so that this operation manual and
warning labels given on the product are understood more. Be familiar with the description and follow
the instruction.
This word used in safety precautions and warning labels indicates potential
danger that may cause deaths or serious injuries.
These safety precautions include preventive measures that must be taken to
avoid danger.
WARNING
CAUTION
This word used in safety precautions and warning labels indicates potential
danger that may cause minor or medium injuries.
These safety precautions include preventive measures that must be taken to
avoid danger.
These warning labels must be always made clear. If the label is peeled off or stained, replace it with a
new one. Contact us or our service center when replacing one.
●Rank of warning indication
Introduction

BEST GRAPHICS
FULL SPECTRUM PRINT | PACKAGING | DIGITAL
CALL FOR DETAILS | 800-236-7603 | bestgraphics.net
PARTS DEPARTMENT
Mike Keller
800-236-7603 ext. 1010
SUBMIT REQUEST ONLINE
FOR FULL MANUAL ACCESS CONTACT
BEST
GRAPHICS
ARCHIVES