ITT Engineered Valves Advantage 2.1 8 Series User manual

Installation and Operation
Manual
Advantage® 2.1 Actuator

Table of Contents
1 Introduction and Safety ....................................................................................................................................2
1.1 Safety message levels .............................................................................................................................. 2
1.2 User health and safety .............................................................................................................................. 2
2 Transportation and storage..............................................................................................................................4
2.1 Handling and unpacking guidelines........................................................................................................... 4
2.2 Storage, disposal, and return requirements ..............................................................................................4
3 Product Description ..........................................................................................................................................5
3.1 Actuator identification ................................................................................................................................ 5
3.2 Bonnet description..................................................................................................................................... 6
3.3 Valve diaphragm identification................................................................................................................... 7
4 Installation..........................................................................................................................................................8
4.1 Precautions ............................................................................................................................................... 8
4.2 Install the valve and topworks ...................................................................................................................8
4.3 Change the compressor, tube nut, and snap ring ..................................................................................... 9
4.4 Mount the topworks to the valve.............................................................................................................. 10
4.5 Tighten the bonnet fasteners...................................................................................................................10
4.6 Fastener torque table for valve body to topworks ................................................................................... 11
4.7 Actuator operating pressure .................................................................................................................... 11
4.8 Set the adjustable opening stop .............................................................................................................. 11
4.9 Disassemble the valve ............................................................................................................................ 12
4.10 Replace the valve diaphragm................................................................................................................12
Table of Contents
Advantage® 2.1 Actuator Installation and Operation Manual 1

1 Introduction and Safety
1.1 Safety message levels
Definitions
Safety message level Indication
DANGER:
A hazardous situation which, if not avoided, will result in death or
serious injury
WARNING:
A hazardous situation which, if not avoided, could result in death
or serious injury
CAUTION:
A hazardous situation which, if not avoided, could result in minor
or moderate injury
ELECTRICAL
HAZARD:
The possibility of electrical risks if instructions are not followed in a
proper manner
NOTICE:
• A potential situation which, if not avoided, could result in an
undesirable result or state
•A practice not related to personal injury
1.2 User health and safety
General precautions
This product is designed and manufactured using good workmanship and materials, and meets all appli-
cable industry standards. This product should be used only as recommended by ITT or ASCO.
WARNING:
•Misapplication of the valve can result in injury or property damage. Select valves and
valve components of the proper materials and make sure that they are consistent with
your specific performance requirements. Incorrect application of this product includes but
is not limited to:
• Exceeding the pressure or temperature rating
• Failing to maintain this product according to the recommendations
• Using this product to contain or control media that is incompatible with the materials
of construction
Qualifications and training
The personnel responsible for the assembly, operation, inspection, and maintenance of the valve must
be appropriately qualified. The operating company must do the following tasks:
• Define the responsibilities and competency of all personnel handling this equipment.
• Provide instruction and training.
1 Introduction and Safety
2 Advantage® 2.1 Actuator Installation and Operation Manual

• Ensure that the contents of the operating instructions have been fully understood by the personnel.
Instruction and training can be carried out by either ITT or the reseller of the valve by order of the operat-
ing companyASCO as the reseller of the valve by order of the manufacturer.
Non-compliance risks
Failure to comply with all safety precautions can result in the following conditions:
• Death or serious injury due to electrical, mechanical, and chemical influences
• Environmental damage due to the leakage of dangerous materials
• Product damage
• Property damage
• Loss of all claims for damages
Operational safety precautions
Be aware of these safety precautions when operating this product:
• Do not leave hot or cold components of the product unsecured against contact if they are a source
of danger.
• Do not remove the contact guard for moving parts when the product is in operation. Never operate
the product without the contact guard installed.
• Do not hang items from the product. Any accessories must be firmly or permanently attached.
• Do not use the product as a step or hand hold.
• Do not paint over the identification tag, warnings, notices, or other identification marks associated
with the product.
Maintenance safety precautions
Be aware of these safety precautions when performing maintenance on this product:
• You must decontaminate the product if it has been exposed to harmful substances such as caustic
chemicals.
Use of unauthorized parts
Reconstruction or modification of the product is only permissible after consultation with ITT. Genuine
spare parts and accessories authorized by ITT serve to maintain safety. Use of non-genuine ITT parts
can annul liability of the manufacturer for the consequences. ITT parts are not to be used in conjunction
with products not supplied by ITT as this improper use can annul all liability for the consequences.
Unacceptable modes of operation
The operational reliability of this product is only guaranteed when it is used as designated. The operating
limits given on the identification tag and in the data sheet may not be exceeded under any circumstan-
ces. If the identification tag is missing or worn, contact ITTASCO for specific instructions.
NOTICE:
ISP employs a magnet to indicate valve position. Other than the calibration/solenoid dongle,
avoid placing magnets on or around the ISP
. Such magnets may erroneously modify the posi-
tion indication.
1.2 User health and safety
Advantage® 2.1 Actuator Installation and Operation Manual 3

2 Transportation and storage
2.1 Handling and unpacking guidelines
CAUTION:
Always observe the applicable standards and regulations regarding the prevention of accidents
when handling the product.
Handling guidelines
Follow these guidelines when handling the product to prevent damage:
•Use care when handling the product.
• Leave protective caps and covers on the product until installation.
Unpacking guidelines
Follow these guidelines when unpacking the product:
1. Inspect the package for damaged or missing items upon delivery.
2. Note any damaged or missing items on the receipt and freight bill.
3. Do not lift or pull on the electrical conduit lines. Doing so may cause the POC switches to come
out of calibration.
2.2 Storage, disposal, and return requirements
Storage
If you are not immediately installing the product after delivery, store it as follows:
• Store the product in a dry room that maintains a constant temperature.
• Make sure that the products are not stacked on top of one another.
Disposal
Dispose of this product and associated components in compliance with federal, state, and local regula-
tions.
Return
Ensure these requirements are met before you return a product to ITTASCO:
• Contact ITTASCO for specific instructions on how to return the product.
• Clean the valve of all hazardous material.
• Complete a Material Safety Data Sheet or Process Data Sheet for any process fluid that could re-
main on the valve.
• Obtain a Return Material Authorization from the factory.
2 Transportation and storage
4 Advantage® 2.1 Actuator Installation and Operation Manual

3 Product Description
3.1 Actuator identification
Design Overview
The actuator is a spring or double acting pneumatic actuator.
To determine if you have an Advantage actuator or an Advantage actuator 2.1 locate the spindle com-
pressor connection and determine if you have a pin connection or modular compressor design.
Figure 1: Pin connection for Advant-
age actuator
Figure 2: Compressor
for Advantage 2.0 ac-
tuator
Figure 3: Modular compressor
with snap ring retention for Ad-
vantage 2.1 actuator
Model number
The actuator model number is located on the ITTASCO identification tag. The model number is a four
digit number defining the actuator as follows.
Table 1: Actuator
Code Description
B Advantage 2.1 actuator
Table 2: Mode of operation
Code Description
1 Fail open (spring to open, air to close) (direct acting)
2 Fail close (spring to close, air to open) (reverse acting)
3 Double acting (air to open, air to close)
Table 3: Actuator series
Code*1 Actuator series*2
03, 04 3
05, 06 5
08, 09 8
16, 17 16
*1 For fail close actuators, codes are specific spring combinations.
*2 Series number equates to diaphragm effective area.
3 Product Description
Advantage® 2.1 Actuator Installation and Operation Manual 5

Table 4: Examples
Model number Description
B308 Advantage 2.1 actuator, double acting, series 8
B216 Advantage 2.1 actuator, fail close, series 16 with a spring set
Identification tag
Line Description
1 Valve serial number
2 Valve size and model number
3 Valve diaphragm type
4 Maximum recommended actuation pressure
3.2 Bonnet description
Non-Sealed bonnet
The non-sealed bonnet has a weep hole that indicates a diaphragm failure by allowing process fluid that
accumulates in the bonnet to pass through the hole.
Sealed bonnet
The sealed bonnet uses a special “V-notch” vent plug, which permits leak detection.
Bonnet
weep hole
V-notch vent plug
(Sealed bonnet only)
Figure 4: Weep hole and V-notch vent plug
3.2 Bonnet description
6 Advantage® 2.1 Actuator Installation and Operation Manual

3.3 Valve diaphragm identification
Diaphragm tab codes
All diaphragm materials and physical properties are batch traceable via permanent codes molded into
the diaphragm tabs. The molding date, grade of diaphragm, and size provide traceability to original batch
records.
1. Date code
2. Supplier code
Figure 5: Elastomer diaphragm front
1. Valve size
2. Grade of diaphragm
Figure 6: Elastomer diaphragm back
1. Material code
2. Date code
Figure 7: PTFE diaphragm
3.3 Valve diaphragm identification
Advantage® 2.1 Actuator Installation and Operation Manual 7

4 Installation
4.1 Precautions
WARNING:
•All procedures must be performed by qualified personnel.
• When the process fluid is hazardous, thermal (hot or cold), or corrosive, take extra pre-
cautions. Employ the appropriate safety devices and be prepared to control a process
media leak.
• Always wear protective clothing and equipment to safeguard the eyes, face, hands, skin,
and lungs from the fluid in the line.
• Do not disassemble the actuator in the field. The actuator contains energized springs
which can cause injury. The product is designed to be recycled in its entirety.
CAUTION:
•Disconnect electrical, pneumatic, and hydraulic power before servicing actuator or auto-
mation components.
4.2 Install the valve and topworks
NOTICE:
The topworks size and configuration can limit the actual operating pressure. Consult the Pure-
Flo catalog for pressure limitations. Consult the factory or engineering catalog for vacuum op-
eration.
Consider the following information before installing the actuator:
•The series 3, 5, 8, or 16 stainless steel bonnet Advantage 2.1 actuator can have the air inlets posi-
tioned in any quadrant.
• The maximum valve operating pressure is 10.34 bar | 150 psig. This pressure is applicable up to
38ºC | 100ºF. Valves at maximum pressure cannot be used at maximum temperatures.
• The maximum actuator pressure is 6.2 bar | 90 psi.
1. If you have a weld end valve, then consider the following:
If you are welding ... Then ...
Manually Remove the topworks.
In line for schedule 10 or heavi-
er pipe
Remove the topworks.
In line for schedule 5 or lighter
pipe and tubing
You can weld with automatic equipment. Before you perform the
weld:
1. Remove the topworks (optional).
2. If left installed, set the valve to the open position.
3. Properly purge the valve with an inert gas.
2. Install the valve.
4 Installation
8 Advantage® 2.1 Actuator Installation and Operation Manual

If the valve is
a ...
Then ...
Dia-Flo dia-
phragm valve
For horizontal piping systems to be drained through the valve, install the valve spin-
dle between 0º and 30º above horizontal. For vertical piping systems, no specific
orientation is required.
Pure-Flo dia-
phragm valve
Install with the raised hash marks (castings) or small machined dots (forgings) on
the valve body at the 12 o'clock position to achieve the optimum drain angle.
3. Prior to pressurization (with the valve slightly open), tighten the bonnet fasteners.
For more information, see 4.5 Tighten the bonnet fasteners on page 10.
4. Connect the air line.
Connection size is 1/8" NPT.
NOTICE:
Air line connections should be made with care so as not to damage the actuator covers.
5. Cycle the valve two to three times to verify smooth operation.
4.3 Change the compressor, tube nut, and snap ring
To switch diaphragm types between EPDM and PTFE, the tube nut must be changed. Follow the steps
below before you switch diaphragm types.
1. Insert a screw driver or similar thin blade between compressor and bonnet flange.
Figure 8: Remove the compressor
2. Apply light pressure to back side of compressor finger.
3. Remove compressor and snap ring assembly.
4.3 Change the compressor, tube nut, and snap ring
Advantage® 2.1 Actuator Installation and Operation Manual 9

Figure 9: Compressor assembly
4. Replace with new snap ring, tube nut and compressor (only 0.5 and 0.75" sizes). Do not re-use
snap ring.
4.4 Mount the topworks to the valve
1. Regulate the air pressure
If the topworks is ... Then regulate the air pressure ...
Fail open or double acting In the upper cover to extend the compressor.
Fail close In the lower cover to properly position the valve diaphragm.
2. Install the valve diaphragm.
For more information, see 4.10 Replace the valve diaphragm on page 12.
3. Assemble the valve body and tighten the bonnet fasteners.
For more information, see 4.5 Tighten the bonnet fasteners on page 10.
4.5 Tighten the bonnet fasteners
CAUTION:
Do not tighten fasteners while the system is pressurized or at elevated temperatures (greater
than 38°C | 100°F).
1. Depressurize the system.
2. Use regulated air pressure to position diaphragm so that valve is slightly open.
You may need to use air pressure to actuate the valve.
3. Tighten the bonnet fasteners in a crisscross pattern.
For more information, see 4.6 Fastener torque table for valve body to topworks on page 11.
4. Make multiple crisscross passes to build up torque to the final table value. Make additional criss-
cross passes using final table values to evenly tighten each fastener to within 5% of torque value.
5. Retighten the bonnet fasteners as noted above at ambient conditions after the system has cycled
through operating pressure and temperature.
6. Monitor the valve for leakage:
If leakage ... Then ...
Occurs at the body/bonnet
flange sealing area
Depressurize the system and retighten the bonnet fasteners as noted
above.
4.4 Mount the topworks to the valve
10 Advantage® 2.1 Actuator Installation and Operation Manual

If leakage ... Then ...
Continues Depressurize the system and retighten the bonnet fasteners as noted
above. (maximum 3rd re-torque)
Continues Replace the valve diaphragm.
For more information, see 4.10 Replace the valve diaphragm on page 12.
4.6 Fastener torque table for valve body to topworks
Values given are for lubricated fasteners.
Valve size Bolt size PTFE diaphragm Elastomer diaphragm
DN Inch Metric Imperial N-m in-lb N-m in-lb
Bio-Tek
(8, 10, 15)
Bio-Tek
(0.25, 0.375,
0.50)
M4 #6 2.3-2.8 20-25 2.3-2.8 20-25
15 0.50 M6 1/4" 2.8-6.8 25-60 2.3-4.5 20-40
20 0.75 M6 1/4" 5.7-9.1 50-65 2.3-5.7 20-50
25 1.00 M8 5/16" 7.4-11.3 65-90 5.1-7.9 45-70
40 1.50 M10 3/8" 23-25 200-225 8.5-14.7 75-130
50 2.00 M12 7/16" 25-31 225-275 11-20 100-180
4.7 Actuator operating pressure
Maximum permitted air supply pressure
bar kPA psi
6.2 620 90
Actuator pressure rating
The actuator will withstand pressures well in excess of the rated pressure without risk of bursting. Main-
taining operating pressure at or below the pressure rating will ensure optimum life of the operating com-
ponents, such as the actuator diaphragm. However, operation at pressures up to 10.3 bar | 150 psig, for
limited periods of time, will not noticeably affect the life of these components.
bar kPA psi
6.2 620 90
4.8 Set the adjustable opening stop
If you have a series 3, 5, 8, 16 actuator, then follow the steps below:
1. Remove the switch package, if present.
2. Using air pressure and a bleed type regulator, open the valve to the desired position.
3. Rotate the adjusting bushing counterclockwise until resistance is felt. The opening stop is now
set.
4. Adjust the valve closed switch.
4.6 Fastener torque table for valve body to topworks
Advantage® 2.1 Actuator Installation and Operation Manual 11

If you have a series 47 actuator, then follow the steps below:
1. Remove the switch package, if present.
2. Remove the clear plastic cap.
3. Using air pressure and a bleed type regulator, open the valve to desired position.
4. Rotate the adjusting bushing counterclockwise until resistance is felt. Count and record the num-
ber of turns.
5. Loosen the two jam nuts and turn the lower nut clockwise the same number of turns as recorded
above.
6. Lock the nuts together.
7. Remove the switch package, if present.
8. Using air pressure and a bleed type regulator, open the valve to the desired position.
9. Rotate the adjusting bushing counterclockwise until resistance is felt. The opening stop is now
set.
10. Adjust the valve closed switch.
11. Replace the clear plastic cap.
4.9 Disassemble the valve
1. Remove all line pressure.
2. If the actuator mode of operation is fail open or fail close, then load the actuator with air.
If the actuator mode of operation is ... Then ...
Fail open Load the actuator with sufficient air to partially close the valve.
Fail close Load the actuator with sufficient air to partially open the valve.
3. Remove the bonnet fasteners.
4. Lift the topworks assembly from the valve body.
5. If the actuator mode of operation is fail open, then remove pressure load from the actuator.
4.10 Replace the valve diaphragm
1. Disassemble the valve.
For more information, see 4.9 Disassemble the valve on page 12.
2. Unscrew the diaphragm from the compressor by turning the diaphragm counterclockwise.
The replacement diaphragm should be identical in size and grade to the original diaphragm.
3. If replacing a PTFE diaphragm, then follow these steps.
a) Install the new elastomer backing cushion over the tube nut.
b) Invert the PTFE diaphragm by pressing the center of the diaphragm face with your thumbs
while holding the edge of the diaphragm with your fingers.
4.9 Disassemble the valve
12 Advantage® 2.1 Actuator Installation and Operation Manual

c) Engage the threads of the diaphragm into the tube nut by rotating clockwise.
d) Continue rotating the PTFE diaphragm clockwise into the compressor while securing the back-
ing cushion from rotating.
4. Rotate the diaphragm until hard stop or heavy resistance is achieved and additional force does not
significantly rotate the diaphragm into the compressor.
5. If replacing a PTFE diaphragm, re-invert the diaphragm.
4.10 Replace the valve diaphragm
Advantage® 2.1 Actuator Installation and Operation Manual 13

6. If the actuator mode of operation is fail open or fail close, select one of these steps.
If the actuator
mode of opera-
tion is ...
Then ...
Fail open Reduce the air pressure until the back of the diaphragm is flat against the bonnet.
Fail close 1. Connect the air line to the bonnet’s cylinder.
2. Load the chamber with sufficient air to move the diaphragm upward until
the back of diaphragm is flat against the bonnet. Do not apply excessive
air pressure that results in inversion of the diaphragm.
7.
For more information, see 4.5 Tighten the bonnet fasteners on page 10.
8. If the actuator mode of operation is fail open, then release the air, allowing the valve to open.
4.10 Replace the valve diaphragm
14 Advantage® 2.1 Actuator Installation and Operation Manual

Visit our website for the latest version of
this document and more information:
www.engvalves.com
ITT Engineered Valves
33 Centerville Road
Lancaster, PA 17603
USA
ITT Industries Ltd.
Weycroft Avenue, Millwey Rise Industrial Estate
Axminster EX13 5HU
United Kingdom
©2020 ITT Inc. or its wholly-owned subsidiaries
The original instruction is in English. All non-English instructions are translations of the original instruction.
Form IO-Adv2.1.en-US.2020-03