Iwata Hi-Line HP-AH User manual

HI-LINE SERIES MANUAL & PARTS GUIDE
1
ANEST IWATA-MEDEA, INC.
Portland, Oregon U.S.A.
[phone]
www.Iwata-medea.com
ANEST IWATA AUSTRALIA PTY LTD.
Mt. Druitt, NSW
[phone]
www.anest-iwata.com.au
ANEST IWATA EUROPE S.R.L.
Torino, Italy
[phone]
www.anest-iwataeu.com
ANEST IWATA SOUTH-EAST ASIA CO., LTD.
Bangkok, Thailand
[phone]
www.anest-iwatasoutheastasia.com
ANEST IWATA SHANGHAI
Shanghai, China
[phone] / 15 / 16
www.anest-iwata-sh.com/ja
ANEST IWATA RUS LLC
Moscow, Russia
[phone]
www.anestiwata.ru
ANEST IWATA CORPORATION
Yokohama, Japan
[phone]
www.anest-iwata.co.jp
ANEST IWATA (U.K.) LTD.
Neots Cambs, England
[phone]
www.anest-iwata.co.jp
ANEST IWATA MOTHERSON LTD.
Uttar Pradesh, India
[phone] / 14 / 17
www.motherson.com
ANEST IWATA SOUTH AFRICA (PTY) LTD.
Johannesburg, Republic of South Africa
[phone]/2265/2223
ANEST IWATA DO BRASIL COMERCIAL LTDA.
Bairro do Paraiso, Sao Paulo
[phone]
www.anest-iwata.net.br
CENTURY TRADING CO., LTD.
Seoul, Korea
82-2-2163-0300
www.centrading.co.kr
If you have any issues with this product,
call ANEST IWATA-MEDEA (U.S.A.) 503-253-7308 (M-F 8am-4pm Pacic Time)
or your local ANEST IWATA aliate before returning to your place of purchase.
NEED ASSISTANCE
Iwata airbrushes are designed for the demanding professional. Modern precision machining and carefully selected materials are used in the
manufacturing process to ensure consistent high performance and long life. Each Iwata Hi-Line airbrush is spray-tested before shipment to assure
maximum performance and adherence to Iwata’s strict quality standards. To maintain your Hi-Line at their peak performance, proper care and
attention must be observed.
ONLY FROM IWATA-MEDEA
Hi-Control of Hi-Precision Work
distinguish these airbrushes as Hi-Line!

QUICK START GUIDE INCLUDED WITH YOUR AIRBRUSH
2
Turn your compressor on.
Using your index nger for
control, push down on the
trigger for air ow. With trigger
pushed down, pull back to
release paint ow. This is
called dual-action.
For ner lines, turn the air
compressor pressure (psi)
down, get close to paint
surface then push down and
pull back on trigger just a little.
Clean airbrush between color
changes and at the end of
your paint session.
BEGIN
1
PAINT
START AIRBRUSHING
PRE-SET AND/OR
CUT-AWAY HANDLES
2
3
MAC VALVE
TO AIR SOURCE
AIR
USE INDEX
FINGER
PRE-SET
KNOB
NEEDLE
CHUCKING NUT
MAC VALVE
AIR
PAINT
FLUID
CAVITY
Some Iwata airbrushes are also equipped
with the MAC Valve (Micro-Air Control
Valve). Turning the knob adjusts the air
ow (psi) for ne control of paint spray.
PAINT
PAINT
If your airbrush has a cup with a
lid, remove by pulling o. Put a
few drops of paint into the color
cup and push lid back on.
If your airbrush has no cup,
then put a drop or two of paint
directly into the uid cavity
found on top of airbrush.
To clean your airbrush, empty excess paint from cup or uid cavity and
wipe out as necessary. Flush out airbrush with the appropriate cleaner
for your medium (such as airbrush cleaner) or use water (good for
water-based mediums) and spray until airbrush sprays clear.
CLEANING
Begin by attaching the small
end of an Iwata air hose
(included with some models or
sold separately) to your airbrush.
Attach the other end of your
airbrush hose to your air source.
(Compressor sold separately
or included with kits.)
Some Iwata airbrushes are equipped with
a preset and/or cutaway handle. The knob
on the pre-set handle limits how far back
you can pull the trigger allowing you to set
a specic line width each time you spray.
The cut-away handle reveals the needle
chucking nut. Pull the needle chucking
nut back and push trigger down and back
when ushing cleaner through airbrush.

HI-LINE SERIES AIRBRUSHES
Obtain ultimate air control at your nozzle tip with Iwata’s Micro Air Control (MAC) Valve Technology. The Hi-Line Series doesn’t just change air pressure instantly - it changes
the way you airbrush.
Designed for artists who need extremely controlled detailed spray, this series uses larger diameter threads on the nozzle than the High Performance Series. This makes the
nozzle much stronger when tightening it onto the airbrush and ensures better centering of the nozzle when it screws onto the airbrush body.
• Solvent-proofPTFEneedlepacking
• Dual-purposecutaway,pre-sethandle
• One-pieceauxiliarylever/needlechuckingguide
• MicroAirControlValveforinstantaneousairowadjustments
• Gravity-feedcongurationallowstheabilitytosprayonjustonedropofpaint
• Strengthenedlargediameterthreadsforbetternozzletipcenteringintheairstream
3
Iwata Hi-Line HP-BH
Iwata Hi-Line HP-AH
Iwata Hi-Line HP-CH
·0.2 mm nozzle
·1/16 oz (1.8 ml) uid cup
·Funneled cup provides quick, easy clean ups
·0.2 mm nozzle
·1/32 oz (0.9 ml) uid cavity
·0.3 mm nozzle
·1/3 oz (9 ml) uid cup
·Funneled uid cup provides quick, easy clean ups
·Ideal airbrush for spraying various paints from
watercolors to solvent-based automotive paints

4
GENERAL OPERATION
Wide-Lines and Blending
1. Depress the main lever (#7).
2.Positiontheairbrushfrom1/2to6inchesawayfromthesurface.
3. Pull the main lever back much further to release more paint to cover
the bigger area.
•Alongerdistancetothepaintsurfaceproduceswiderlines.
•Ashorterdistancetothepaintsurfaceproducesnarrowerlines.
•Increasedairpressureincreasesspraywidth.
•Decreasedairpressuredecreasesspraywidth.
•Themaximumusablelinewidthisapproximately2inches.
Pre-Set Handle (#17)
A threaded adjusting screw mounted behind the handle limits the distance the main
lever can be pulled back.This provides accurate paint volume control and is especially
useful for repetitive, precision work.
Cutaway Handle
The cutaway handle allows quick paint clog removal without removing the handle
or needle.
1.Griptheexposedneedlechucklingnut(#16)withyourngers.
2. Pull it back while simultaneously depressing the main lever (#7).
3. Repeat this process several times until the airbrush is clog free and
spraying normally.
•Theincreasedpaintowpastneedleandnozzletipremovesmanyclogs.
•Don’tlettheneedle“snap”backintoplace.Thiscoulddamagethenozzle.
Micro Air Control (MAC) Valve
The MAC Valve (#29) enables innite airow control at the airbrush’s head providing
control between stipple, ne detail, and background spray effects.
•Spraycoarsestipplingeectsandincreasetofullatomizationinaquickturn.
•Finetunedairow.
•Maximizedpaintatomizationcontrol.
•Openthevalvefullyduringcleaning.Thehigherpressurepullsmorepaint
through the airbrush.
Stippling
Iwata airbrushes are designed to produce a wide range of stippling textures.
1. Unscrew the needle cap (#1).
2. Unscrew the nozzle cap (#2).
3.Adjusttheairpressurebetween8and60psi.
•Lowairpressurecreatescoarsestipples.
•Highairpressureprovidesnestippleeects.
•Paintviscosityalsoeectsstipplingtexture.
Air Pressure
Working pressures generally vary between 8 and 60 psi, depending on the type of
surface, the desired spray texture, and the paint’s viscosity.
Start spraying with 15 psi. If the spray is too grainy adjust the pressure up until the
desired spray consistency is reached.
• Different colors will behave differently.
• Different paint lines will behave differently.
• Spray thick paint with greater pressure.
• Spray thin paint with less pressure.
• Spray large paint amounts with greater pressure.
• Spray small paint amounts with less pressure.
WARNING: Do not exceed 98psi.
Paint Preparation
For non-specic airbrush paints, proper preparation, including ltering the paint
through a nylon mesh, is critical for best performance.Thin paint with its proper
solvent, and make repeated passes across the work to build up the color.This
improves your work’s quality and decreases your airbrush’s cleaning time.
• Airbrushes spray very thin paint easiest.
• Thin paint with its proper solvent.
• Filter paint through paint lters or mesh.
Safety Tips
•Alwayssprayinwellventilatedareas.
•Donotspraysolventbased(ammable)paintsaroundopenames.
•Usetheappropriaterespiratortosafelylteroutpaintvaporsparticulartoyour
specicpainttype.
•Weareyeprotectiontopreventpaintcontactwitheyes.
•Neverexceedtheairbrush’spressurelimit(98psi).
GETTING STARTED
Compressor
Though Hi-Line Series airbrushes can function on minimal amounts of air, their full
versatility requires an adjustable or regulated air source with an air storage tank.
Other compressor considerations include the length of use while spraying
and the environment, or amount of space, you spray in.
These Iwata Studio Series models come equipped with an air regulator for precise
air adjustment:
•SmartJetPro:Goodforsmallstudiosandnormaluse.
•PowerJetLite:Goodfornormalstudiosandextendeduse.
•PowerJet:Greatfornormalstudiosandgreatforextendeduse.
•PowerJetPro:Greatfornormalstudiosandgreatforextendeduse.
(Two regulators allow two airbrushes on same unit.)
Assembly
1. Screw the airhose onto the compressor.
2. Screw the airhose onto the airbrush.
3.IfusingaSmartJetPro,PowerJet,PowerJetLite,orPowerJetProcompressor,
adjustthepressuretobetween10and15psi.
4. Check for any air leaks in the compressor or airhoses.
5.Placeafewdropsofcleaningsolutionorwaterintotheairbrush’sbowl.
6.Pointtheairbrushawayfromyou.
7.Pressdownonthemainlever(#7)tostartairowthroughtheairbrush.
8. Pull the main lever back opening the airbrush’s nozzle.
9.Spraywaterthroughtheairbrushtoseehowitsprays.

5
Cleaning the Airbrush Between Colors
1. Dump out the color cup’s excess paint.
2. Rinse the cup with the appropriate cleaning solution.
3. Use a paper towel to wipe out any left over paint.
4. Fill the bottom of the cup with cleaner.
5.Spraycleaneruntilthesprayisclear.
6.Addthenextcolortothecolorcup.
7.Repeatcleaningprocedurewhennished.
Cleaning the Needle (#4)
1. Unscrew the handle (#17) from the airbrush body.
2.Loosentheneedlechuckingnut(#16).
3.Gentlypulltheneedle(#4)straightout.
4. Fold a soft cloth damp with cleaner over the needle.
5.Rotatetheneedletogentlywipetheresidualpainto.
6.Carefullyinserttheneedleintotheairbrushuntilitseatsfullyagainstthenozzle
(#3). You should feel a positive stop. If you feel a spongey stop, you still have debris
in your nozzle.
CAUTION:The most probable time to damage the needle is when the
needle passes through the main lever (#7) and through the needle packing
screw (#5).
If the needle stops abruptly, retract and examine the trigger mechanism
for proper assembly and re-insert the needle.
7.Tightentheneedlechuckingnutngertight.
•Pullthemainleverbackandforthtovisuallyconrmtheneedle’sabilitytomove.
8. Screw the handle back onto the airbrush body.
Before Each Session
Spray water or the appropriate paint solvent through the airbrush to make sure the
airbrush is working properly.
After Each Session
Or any time the airbrush becomes clogged.
1. Increase the air pressure.
2. Spray cleaning solution for a short time.
3. Clean the needle if necessary
This cleaning method helps clean the paint passage, the nozzle, and the
needle thoroughly.
Lubricating the Needle (#4)
To ensure smooth main lever (#7) action lubricate the needle when the trigger won’t
respond properly.
1. Unscrew the handle (#17).
2. Loosen the needle chucking nut (#16).
3. Remove the needle.
4. Coat the needle slightly with Medea Super Lube starting 1 inch behind the tip.
5.Wipe the needle with a soft, clean cloth, leaving a light coat of lube behind.
6. Re-insert the needle gently into the airbrush until you feel a positive stop.
7.Tighten the needle chucking nut.
8. Screw the handle onto the airbrush body.
DO NOT over-lube the needle; transferring excess lube into the nozzle may
cause severe paint ow problems.
DO NOT use light machine oil or WD-40 for lubrication.These lubes cause
the needle to stick when it moves through the needle
packing o-ring and can also get into the air system.
CAUTION: If it becomes absolutely necessary to dismantle the airbrush
remember that most situations do not require tools.
DO NOT use pliers.
Lubricating the Air Piston (#12)
To ensure smooth main lever (#7) action lubricate the air piston when the trigger
won’t respond properly.
1. Unscrew the handle (#17).
2. Unscrewtheneedlechuckingnut(#16).
3. Remove the needle (#4).
4. Unscrew the spring guide (#11).
5. Removetheneedlespring(#10).
6. Removetheneedlechuckingguide(#9).
7. Pull the main lever up and out.
8. Use tweezers to pull out the air valve piston.
9. Cleantheairpistonwithacottonswab.
10.Cleantheholeatthebottomofthetrigger
housing with a cotton swab.
a. Clean until a Cotton Swab comes back clean.
11. Dab a very small drop of Super Lube on the air piston shaft.
12. Insert the air piston back into the hole at the bottom of the trigger housing.
13. Place the main lever back into the trigger housing.
14. Press the main lever up and down a few times.
a. It should spring back up smoothly when depressed.
15. Placetheneedlechuckingguideintotheairbrushbody.
a. Check the parts guide for proper orientation.
b. Pull the small tab forward.
c. Angle the needle chucking guide’s tail end slightly up.
d. Insert the needle chucking guide into the airbrush body.
e. The small tab should stick up slightly behind the main lever.
16. Placetheneedlespringovertheneedlechuckingguide.
17. Screw the spring guide into the airbrush body.
18. Push down on the main lever at least once.
19. Carefullyinserttheneedle.
 a.Warning:Thisisthemostprobabletimetobendtheneedlepoint.
20. Screwtheneedlechuckingnutontotheneedlechuckingguide.
21. Screw the handle back into the airbrush body.
DO NOT over-lube the air piston; transferring excess lube into the air
system may cause severe paint ow problems.
DO NOT use light machine oil or WD-40 for lubrication.These lubes cause
the needle to stick when it moves through the needle packing o-ring.
CAUTION: If it becomes absolutely necessary to dismantle the airbrush
remember that most situations, unless otherwise directed, do not
require tools.
MAINTENANCE REFER TO MASTER PARTS LIST ON PAGE 7

Symptom Problem Solution
Not Spraying Loose needle chucking nut •Finger tighten (#11)
Needle stuck •Pull out/Break-free Needle (#10)
Improper air pressure •See specific compressor instructions
to raise or lower the air pressure
Paint too thick •See Paint Preparation
Clogged nozzle •See Head System (#1) and clean nozzle (#1C)
with toothpick
Cracked or damaged nozzle •See Head System (#1) to replace the head system
Skipping Dried paint on needle tip (Tip-Dry) •See Cleaning the Needle
Paint too thick •See Paint Preparation
*Improper nozzle to head system base connection •See Head System (#1) to reseat the nozzle
Dirty airbrush •See Cleaning the Airbrush Between Colors
•See Cleaning the Needle
Cracked or damaged nozzle •See Head System (#1) to replace the head system
TROUBLESHOOTING PROCEDURES
*Warning: The most likely time to damage the nozzle (#1C) is upon removal from the airbrush. Because the Head System can be removed
entirely the nozzle does not need to be removed at all. If the nozzle is never removed you do not have to worry about "improper nozzle to
head system base connections".
Symptom Problem Solution
Not Spraying Loose needle chucking nut •Finger tighten (#11)
Needle stuck •Pull out/Break-free Needle (#10)
Improper air pressure •See specific compressor instructions
to raise or lower the air pressure
Paint too thick •See Paint Preparation
Clogged nozzle •See Head System (#1) and clean nozzle (#1C)
with toothpick
Cracked or damaged nozzle •See Head System (#1) to replace the head system
Skipping Dried paint on needle tip (Tip-Dry) •See Cleaning the Needle
Paint too thick •See Paint Preparation
*Improper nozzle to head system base connection •See Head System (#1) to reseat the nozzle
Dirty airbrush •See Cleaning the Airbrush Between Colors
•See Cleaning the Needle
Cracked or damaged nozzle •See Head System (#1) to replace the head system
TROUBLESHOOTING PROCEDURES
*Warning: The most likely time to damage the nozzle (#1C) is upon removal from the airbrush. Because the Head System can be removed
entirely the nozzle does not need to be removed at all. If the nozzle is never removed you do not have to worry about "improper nozzle to
head system base connections".
Symptom Problem Solution
Bubbles in Color Cup or Bottle Loose nozzle cap •Tighten (#1B) finger tight
*Improper nozzle to head system base connection •See Head System (#1) to reseat the nozzle
Cracked or damaged nozzle •See Head System (#1) to replace the head system
Double Line Dried paint on needle tip (Tip-Dry) •See Cleaning the Needle
Dirty airbrush •See Cleaning the Airbrush Between Colors
•See Cleaning the Needle
Debris on nozzle tip •See Head System (#1) and clean nozzle (#1C)
with toothpick
Bent needle •See Needle (#10) to replace needle
Cracked or damaged nozzle •See Head System (#1) to replace the head system
TROUBLESHOOTING PROCEDURES
*Warning: The most likely time to damage the nozzle (#1C) is upon removal from the airbrush. Because the Head System can be removed
entirely the nozzle does not need to be removed at all. If the nozzle is never removed you do not have to worry about "improper nozzle to
head system base connections".
TROUBLESHOOTING PROCEDURES
Symptom Problem Solution
Spattering Dried paint on needle tip (Tip-Dry) •See Cleaning the Needle
Paint build-up in crown cap •Unscrew (#1A) and clean with cotton swab
Air pressure too low •See specific compressor instructions to raise
the air pressure
Paint too thick •See Paint Preparation
Dirty airbrush •See Cleaning the Airbrush between Colors
•See Cleaning the Needle
Trigger Sticks (back and forth) Dirty airbrush •See Cleaning the Airbrush between Colors
•See Cleaning the Needle
Trigger Sticks (up and down) Paint on air valve packing o-ring •See Lubricating the Air Piston
TROUBLESHOOTING PROCEDURES
6

7
IWATA HI-LINE SERIES
n= yes x= no opt = optional
13C
3
15
13A
13B
25
7
12
30
30
9
5
16
4
17
28
10
11
15B
15C
15D
15A
29
2
1
PRICE ITEM ALSO
# ITEM DESCRIPTION CODE # HP-AH HP-BH HP-CH FITS
1 Needle Cap B I 110 1 nnxHP-A/+
B I 110 2 xxnHP-C/+
2 Nozzle Cap D I 140 7 nnopt
D I 140 3 opt opt nHP-C/+
3 Fluid Nozzle 0.20 mm G I 080 7 nnopt HP+
0.30 mm G I 080 8 opt opt nHP+
4 Fluid Needle 0.20 mm C I 075 1 nnopt HP-A/+
0.30 mm C I 075 3 opt opt nHP-C/+
5 Needle Packing Screw B I 125 7 nnx
w/PTFE Needle Packing B I 725 1 xxnREV
7 Main Lever D I 100 2 nnnHP-C/+
9 Needle Chucking Guide C I 115 7 nnx
w/Auxiliary Lever C I 715 1 xxnREV
10 Needle Spring A I 135 2 nnxHP-A/+
A I 135 1 xxnECL/REV
11 Spring Guide A I 770 1 nnnREV
12 Valve Piston A I 175 1 nnnHP-A/+
13A Body* nxx
13B xnx
13C xxn 
14 PackingValve Piston (O-Ring) A I 145 1 nnnHP/+
PRICE ITEM ALSO
# ITEM DESCRIPTION CODE # HP-AH HP-BH HP-CH FITS
15 Air Valve Set G I 030 1 nnxHP-A/+
G I 030 4 xxnHP-C/+
15A Air Valve Guide A I 025 1 nnnHP/+
15B Air Valve Body D I 020 1 nnnHP/+
15C Air Valve B I 015 1 nnxHP-A/+
B I 015 4 xxnHP-C/+
15D Air Valve Spring A I 035 1 nnnHP/+
16 Needle Chucking Nut A I 120 1 nnnHP/+
17 Pre-Set Handle Set G I 155 6 nnn 
25 Fluid Cup Lid C I 618 1 xxnHP-C/+
28 Packing Handle (O-Ring) A I 605 1 nnnCM-C+
29 Micro Air Control (MAC)Valve D I 190 1 nnnCM-C+
30 Packing MAC Valve (O-Ring) A I 190 2 nnnCM-C+
Spanner (Nozzle Wrench) A I 165 1 nnnHP/+
Quick Fit Set I 160 3 opt opt opt
(QD Screws Onto Airhose and
Adaptor Screws Onto Airbrush)
Quick Fit Adaptor I 160 4 opt opt opt
(Adaptor Screws Onto Airbrush)
Adaptor (Iwata Airbrushes to J 001 optopt opt
Paasche Air Hose)
Adaptor (Iwata Airbrushes to J 002 optopt opt
T & C/Badger Air Hoses)
CA PROP
65
CA PROP
65
CA PROP
65
CA PROP
65
CA PROP
65
CALIFORNIA PROP 65 WARNING: Certain products identied with this symbol and oered for sale in this catalog contain lead,
a chemical known to the State of California to cause cancer, birth defects and other reproductive harm.
CA PROP
65
*Replacement parts not available.

Changing the Tip Size
To fully and completely change the airbrush’s tip size and maintain performance switch out the needle, nozzle, and
nozzle cap according to this chart.
HP-AH 0.2 mm Standard I 075 1 I 080 7 I 140 7 I 125 7
HP-AH 0.3 mm Optional I 075 3 I 080 8 I 140 3 I 725 1
HP-BH 0.2 mm Standard I 075 1 I 080 7 I 140 7 I 125 7
HP-BH 0.3 mm Optional I 075 3 I 080 8 I 140 3 I 725 1
HP-CH 0.2 mm Optional I 075 1 I 080 7 I 140 7 I 125 7
HP-CH 0.3 mm Standard I 075 3 I 080 8 I 140 3 I 725 1
Model Tip Size Setup Needle Nozzle Nozzle Cap PTFE O-Ring
REPLACEMENT PARTS AND ACCESSORIES
Nozzle (#3)
In time, the nozzle may wear or be damaged and may need to be replaced.
1. Unscrew the handle (#17).
2. Loosen the needle chucking nut (#16).
3. Gently pull the needle (#4) part way back. It doesn’t need to be fully pulled out.
4. Unscrew the nozzle cap (#2)
5. Unscrew the nozzle counter-clockwise with the provided wrench.
6. Screw the new nozzle into the airbrush body with your ngers.
7. Slightly tighten the nozzle with wrench. DO NOT OVER TIGHTEN!
8. Screw the nozzle cap onto the airbrush body.
9. Push the needle all the way forward until it seats with the new nozzle.
10.Tighten the needle chucking nut.
11. Screw the handle onto the airbrush body.
TIP: Keep a spare nozzle on hand for unforeseen accidents.
Needle (#4)
Iwata needles are precision ground, hardened stainless- steel capable of withstanding
prolonged use.They are, however, easily physically damaged because of the long, tapered,
extremely ne tip. If the needle point becomes severely bent, it must be straightened
before pulling it back through the nozzle. If not, the bent needle might damage the nozzle
as it’s pulled through.
TIP: Keep a spare needle on hand for unforeseen accidents.
• Needles are sharp.
• Needle tips are bent easily.
Crown Cap (Optional Accessory)
The crown cap physically protects the needle while spraying very ne lines. It also
adds to pigment build-up and spattering when spraying large backgrounds.
• Protects the needle
• Replaces the needle cap (#1)
• Adds to pigment build-up and spattering effects over large areas
Quick Disconnect (Optional Accessory)
A quick disconnect joint is screwed onto the airhose and a quick disconnect adapter is
screwed onto each airbrush.When using multiple airbrushes the quick disconnect joint
facilitates changing airbrushes on the same airhose quickly.
Pistol Grip Moisture Filter
The Iwata-Medea Pistol Grip Moisture Filter delivers clean, dry air to your airbrush.
Miniature in size, the super-ne, 5-micron lter element performs like a full-size
lter separator.
The clear lter bowl allows visual inspection of built up moisture. Release the water
by pulling the spring-loaded release valve.
8

Copyright©2014Iwata-MedeaInc.Allrightsreserved.TheIwata-Medealogo,Iwata-Medea®,IwataEclipse™,IwataRevolution™,IwataKustom™,IwataMicron™,SprintJet™,SmartJet™,PowerJetPro™,PowerJetLite™,MedeaSuperLube™,PistolGripFilter™,and
allproductsdenotedwith®or™areregisteredtrademarksortrademarksofIwata-MedeaInc.•Iwata®andtheIwatalogoareregisteredtrademarksofAnestIwataJapan.Formoreinformationvisitwww.iwata-medea.com
Rev211/2014
— www.IWATAAIRBRUSH.com —
ANEST IWATA-MEDEA, Inc.•1336N.MasonSt.,Portland,OR97217
tel: 503-253-7308     •     fax: 503-253-0721     •     [email protected]om
WARRANTY
All NEO for Iwata airbrushes are Warranted against all manufacturing defects of material and manufacture or workmanship for a period of FIVE years from the
dateofpurchase.Thiswarrantydoesnotcoveruidneedlesoruidnozzlessincethesepartsneedtobereplacedoccasionallyduetonormalwear.Anyotherpartor
material that is or becomes defective so as not to be usable within this period will be repaired or replaced. This warranty does not cover damage caused by negligence
or airbrushes that have been altered or abused in any way. Call or email Iwata-Medea before returning an airbrush for the appropriate procedure for warranty repairs.
9