IXYS Zilog S3F80QB User manual

S3 Family of Microcontrollers
S3F80QB Development
Kit
Copyright ©2016 Zilog®, Inc. All rights reserved.
www.zilog.com
UM026704-0816
User Manual

UM026704-0816 Disclaimer
S3F80QB Development Kit
User Manual
ii
DO NOT USE THIS PRODUCT IN LIFE SUPPORT SYSTEMS.
LIFE SUPPORT POLICY
ZILOG’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE
SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF
THE PRESIDENT AND GENERAL COUNSEL OF ZILOG CORPORATION.
As used herein
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b)
support or sustain life and whose failure to perform when properly used in accordance with instructions for
use provided in the labeling can be reasonably expected to result in a significant injury to the user. A criti-
cal component is any component in a life support device or system whose failure to perform can be reason-
ably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
Document Disclaimer
©2016 Zilog, Inc. All rights reserved. Information in this publication concerning the devices, applications,
or technology described is intended to suggest possible uses and may be superseded. ZILOG, INC. DOES
NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE
INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO
DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED
IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED
HEREIN OR OTHERWISE. The information contained within this document has been verified according
to the general principles of electrical and mechanical engineering.
S3 and Z8 are trademarks or registered trademarks of Zilog, Inc. All other product or service names are the
property of their respective owners.
Warning:

UM026704-0816 Revision History
S3F80QB Development Kit
User Manual
iii
Revision History
Each instance in this document’s revision history reflects a change from its previous edi-
tion. To learn more, refer to the corresponding page(s) or appropriate links furnished in the
table below.
Date
Revision
Level Description Page
Aug
2016
04 Updated for ZDS-S3 version 5.3.0. Removed ISP I support All
Oct
2014
03 Updated the Establish a Connection with the PC and High-Power Infrared-
Emitting Diode sections; added sample projects to Table 3.
4, 17,
21
Sep
2014
02 Updated the sections Start the Ledblink Sample Program and Install the S3
Flash ISP Driver for improved usability.
7, 23
Jun
2014
01 Original issue. n/a

UM026704-0816 Overview
S3F80QB Development Kit
User Manual
1
Overview
Zilog’s S3F80QB Development Kit, part number S3F80QB0100ZCOG, allows you to
evaluate your S3F80QB-based designs and applications. The Kit features a Development
Board consisting of the following components:
• Four LEDs
• Seventeen pushbuttons
• Buzzer/speaker
• Four high-power infrared (IR) emitting diodes
• IR receiver module
• Device pin headers
This user manual provides instructions for setting up and configuring the S3F80QB
Development Board. It includes schematic diagrams and a discussion of the Board fea-
tures and ZDSII.
The S3F80QB Development Board features an S3F80QB MCU in a 44-pin QFP package,
plus an S3 PGM connector to connect the Board to a host development PC using the S3
Flash In-System Programmer II (ISP). To learn more about the S3F80QB MCU, refer to
the S3F80QB Product Specification (PS0308) and/or the S3 Flash In-System Programmer.
This document guides you through the following tasks:
• Downloading and installing ZDSII software and documentation
• Connecting the S3 Flash ISP II and S3F80QB Development Board to your PC
• Starting the S3F80QB Ledblink sample program

UM026704-0816 Kit Contents
S3F80QB Development Kit
User Manual
2
Figure 1 shows the contents of the S3F80QB Development Kit.
Kit Contents
The S3F80QB Development Kit contains the following items:
• S3F80QB Development Board
• S3 Flash ISP II
• 10-circuit ribbon cable
• USB A (male) to Mini-B USB cable (2)
• S3F80QB Development Kit hardcopy insert
Figure 1. The S3F80QB Development Kit

UM026704-0816 Features
S3F80QB Development Kit
User Manual
3
Features
The S3F80QB Development Kit includes the following key items.
• S3F80QB Development Board, which contains the following features:
–S3F80QB 44-pin QFP MCU operating at 8MHz, with 63KB of internal Flash
memory and 1KB of internal RAM memory
–USB interface that provides power to the Board
–High-power infrared emitting diode
–Buzzer/Speaker
–IR receiver module
–Test points for all pins of the MCU
–MCU current measurement test points J7 and J8
–Power supply level adjustable with potentiometer R18
• S3 Flash In-System Programmer II
• ZDSII software, samples, and documentation available free for download
–Sample programs
Supported Host Environments
The S3F80QB Development Board supports the following operating systems:
• Microsoft Windows 7 (32-bit/64-bit)
• Microsoft Windows 8 (32-bit/64-bit)
Install the ZDSII Software and Documentation
Observe the following steps to download and install your ZDSII software and documenta-
tion.
If you have already installed ZDSII S3 <version> and have downloaded the software and
documentation by following the procedure on the paper insert in your kit (FL0166), skip
ahead to the next section.
Note:

UM026704-0816 Establish a Connection with the PC
S3F80QB Development Kit
User Manual
4
1. Prior to connecting the S3F80QB Development Board to your development PC,
download ZDSII for S3 Family devices version 5.3.0 (or later) from the Download-
able Software category in the Zilog Store.
2. When the download is complete, unzip the file to your hard drive. Double-click the
installation file named ZDSII – S3_<version>.exe, and follow the on-screen instruc-
tions.
Establish a Connection with the PC
Observe the following procedure to connect the S3 Flash ISP II and S3F80QB Develop-
ment Board to your PC.
Disconnect or turn off the power to the S3F80QB Development Board before connecting
or disconnecting the S3 Flash ISP II.
1. Connect the Mini-B side of the USB A (male)-to-Mini-B cable to the S3 Flash ISP II.
Connect the other end of this cable to the PC, as shown in Figure 2.
2. Connect the 10p 5x2 ribbon cable to the S3 Flash ISP II, as shown in Figure 3.
Figure 2. Connect the S3 Flash ISP II to the Development PC
Caution:

UM026704-0816 Establish a Connection with the PC
S3F80QB Development Kit
User Manual
5
3. Connect the other end of the ribbon cable to Jumper J6 on the Development Board.
Ensure that Pin 1 on the ribbon cable is aligned with Pin 1 on the target connector, as
indicated in Figure 4.
Figure 3. Connect the 10-Pin Ribbon Cable to the S3 Flash ISP II
Figure 4. Debug Connector J6

UM026704-0816 Establish a Connection with the PC
S3F80QB Development Kit
User Manual
6
When connecting the 10-pin ribbon cable, be sure to use the correct orientation to prevent
damage to the S3 Flash ISP II.
4. With the USB A (male) to Mini-B cable, connect Port P1 on the S3F80QB Develop-
ment Board to a USB port on the development PC to apply power to the Development
Board, as indicated in Figure 5.
After completing the procedure to connect the S3F80QB Development Board to the PC,
the complete setup appears as shown in Figure 6.
Figure 5. The Power Supply Port P1 Connector
Caution:

UM026704-0816 Start the Ledblink Sample Program
S3F80QB Development Kit
User Manual
7
Start the Ledblink Sample Program
The S3F80QB Development Kit includes a sample program that demonstrates an LED
blinking application. To get started with the S3F80QB Ledblink sample program, observe
the following procedure.
1. Launch ZDSII by navigating from the Windows Start menu to Programs →Zilog
ZDSII –S3 <Version> →ZDSII –S3 <Version>.
2. From the File menu in ZDSII, select Open Project as indicated in Figure 7, and navi-
gate to the following filepath:
<ZDS Install>\samples\S3F80QB\ledblink_asm
Figure 6. The Completed ISP II and Development Board Assembly