Jabra GN9010-BT User manual

GN9020-D
Digital Wireless System
GN9010-BT
Bluetooth™ Wireless System
User Guide

Assembling
1Connect all cords.
2Attach the base station to the stand.
Charging the Battery
3Insert the headset
into the base station
(either side can
be used). The
battery charging
indicator on the
base illuminates.
4The headset battery
is not charged
when delivered.
Place the headset
in the base for 3
hours before making
the following
adjustments. It takes
3 hours to fully
charge the battery.
When fully charged,
the battery charging
indicator flashes.
— A fully charged GN9020-D provides 7 hours
of talktime.
— A fully charge GN9010-BT provides 2 hours
of talktime.
Netcom

Checking the System
5If your telephone has volume control, set the
volume in the middle position.
6Press the headset/handset
selector to switch on the
headset. The headset mode
indicator on the base station
illuminates.
7The headset
mode indicator
on the headset
begins flashing
within 10
seconds. If the
headset mode
indicator does
not flash, recheck
assembly.
8The system is now working.
9If the lights are still off, the headset/handset selector
is in handset position. Press the headset/handset
selector once.
Adjusting to yourTelephone
10 Put on the headset.
11 Make sure the mute
function is off. If
you hear a beep
every 3 seconds, the
mute function is on.
Turn off the mute
function by pressing
the mute button
once.
12 Lift the handset
from your telephone
and listen for a dial
tone in your headset.
13 If there is no dial
tone, adjust the tele-
phone compatibility
setting until the dial
tone is clear. If dial
tone is clear for both
A and G, set to A.
¥1
¥2
¥3
¥4
¥5
¥6
¥7
¥8
¥A
¥B
¥C
¥D
¥E
¥F
¥G

Adjusting the MicrophoneVolume
14 Put on the headset.
15 Press the headset/handset selector
to switch to handset mode.
16 Call someone using your handset and ask the person
to help you evaluate the volume of your voice.
17 Using the
headset/handset selector
to toggle back and forth
between handset and
headset mode, adjust
the microphone volume
control from 1 to 8 by
first talking in the
handset and then in the
headset in each switch
position. Position 1 is
the lowest volume setting
and position 8 is the
highest volume setting.
18 When the person hears
no difference whether
you talk in the handset
or headset, you have the
correct setting. If the
setting is 7 or 8, it may
be necessary to move the
telephone compatibility
setting to G. Some
phone handsets may
always be louder than
the headset.
¥1
¥2
¥3
¥4
¥5
¥6
¥7
¥8
¥A
¥B
¥C
¥D
¥E
¥F
¥G

Answering and Placing Calls
19 Put on the headset.
20 Set the headset/handset selector
to headset position.
21 Lift the handset
from the phone.
Answer or place
the call.
22 You can now move
freely away from
the base station. If
you move out of
transmission range,
you will hear a beep
in the headset every
10 seconds.
23 To end the call,
replace the handset
on the phone.

Adjusting the ReceiveVolume
24 To increase or decrease the
volume, press the upper (+)
or lower (-) part of the
oval volume control on
the headset. When the
volume reaches maximum
or minimum, you will hear
a beep in your headset.
Muting the Microphone
25 To talk without the other
party hearing you, press
the mute button on the
headset. When the
microphone is muted,
you will hear a beep
every 3 seconds. When
the mute function is on,
you can still hear the
other party.
Recharging the Battery
26 To ensure optimum
battery life, when not
in use, place the headset
in the base station with
the headset/handset
selector in the handset
position. The battery
charging indicator
illuminates during
recharging. It takes 3
hours to fully charge
the battery. When fully
charged, the indicator
flashes. If battery
power gets too low,
you will hear a beep
in your headset every
20 seconds.

ComfortAdjustments
28 You can wear the
headset on your
right or left ear,
whichever side you
prefer. To switch
sides, simply rotate
the microphone
boom below the
headband. NOTE:
Do not force the
boom over the top
of the headset.
29 Adjust the length of
the headband so the
headset rests com-
fortably on your
head. The stabilizer
should be placed just
above your free ear.
Adjust the flexible
microphone boom so
the microphone is
positioned approxi-
mately 1/2” (12 mm)
from your mouth.
30 To change or clean
the leatherette ear
cushion, first
remove the earplate
by turning the
earplate 45 degrees
counter-clockwise.
Once removed, the
ear cushion can be
taken off the
earplate.
To use the optional
foam ear cushion,
first remove the
earplate and
leatherette cushion.
Then place the
foam cushion on
the earplate.
31 Gently remove the
microphone foam cover
to clean or change.

FrequentlyAsked Questions
Why can’t I hear a dial tone?
• Check that all cords are connected correctly.
• Be sure the AC power adapter is plugged in and power
is turned on.
• Be sure the headset/handset selector is in headset
position and the headset mode indicators are
illuminated.
• Be sure the battery is fully charged.
• Be sure the serial numbers on the base station and
headset match. The numbers must match for operation.
• Adjust the telephone compatibility setting.
Why doesn’t the other person hear me?
• Be sure the mute function is off.
• Re-adjust the microphone volume.
• Check the position of the microphone making sure
that it is placed at the corner of your mouth.
• You may be out of range. Move cl

Cautionary Notes to Computer Users
When using any headset with a computer, care should be taken in dry or low humidity environments to protect the user from electrostatic discharge from
the monitor (CRT). Computer monitors can induce a substantial electrostatic charge when turned on or off, or when there is a power failure, and the
resulting electrostatic discharge can be passed through the headset to ground.
A user in close proximity to or touching the computer may feel a common “shock” sensation, similar to touching a doorknob after walking across a carpet,
causing no harm to the user. This discharge is entirely due to the computer monitor; the headset is merely the shortest path to ground.
To minimize the possibility of electrostatic discharge through the headset, you can:
• Use a grounded screen in front of the monitor.
• Use static dissipative wrist straps.
• Increase the relative humidity in the room to 60% or more.
• Install static dissipative carpets or floor coverings (anti-static sprays can be helpful).
• Remove the headset before turning the computer on or off.
GN Netcom, Inc. headsets meet all OSHA, UL, FCC and CS standards.