jacarta interSeptor User manual
Ethernet Environmental Monitoring Unit
Quick Installation Guide
V 2.6
www.jacarta.com
T. +44 (0) 1672 511125
Email: [email protected]
Thank ou for purchasing the interSeptor
Please use the ollowing instructions to install the interSeptor
interSeptor Hardware Installation
For serial con iguration
1. Connect the supplied RJ45/DB9(M) serial cable rom the interSeptor’s RJ45
connector labeled “EMD-2” to the COM port on the PC.
2. Connect the supplied ‘straight-through’ CAT 5 cable rom the interSeptor’s RJ45
connector labeled “EMD-1” to the RJ45 port on the EMD.
3. I applicable, connect external sensors to the screw terminals on the EMD.
4. Insert the power connector into the interSeptor power inlet.
5. Plug in the power adapter o the interSeptor into the power socket.
6. Follow the “Con iguring interSeptor via the serial port” instructions.
For network con iguration
1. Connect a standard CAT5 straight through network cable between the interSeptor’s
network port and a spare network socket on your network.
2. Follow steps 2 through ive rom the “For Serial Con iguration” instructions.
3. Follow the “Con iguring interSeptor on the network” instructions.
Configuring interSeptor via the Serial Port
1. Start a Hyperterminal session on your Windows PC.
2. Enter a name or the interSeptor session and press
“OK”.
3. Select the correct COM port and press “OK”.
4. Con igure the port settings as shown (9600, 8,
None, 1, None) and press “OK”.
5. Set DIP switches on the rear panel o the interSeptor
to SW1=OFF, SW2=OFF.
6. Power up the interSeptor
7. Enter the de ault password “admin” and at the
prompt enter “1” and press enter, then press “1”
and enter again to open the System Group menu.
8. Assign an IP address or interSeptor, and the correct subnet mask.
NOTE: Both PC and interSeptor P addresses must be on the same P subnet.
9. Enter “0” and back to the interSeptor Configuration menu.
10. Enter “2” to go to the Control Group menu.
11. Disable the “BOOTP / DHCP” option.
12. Con igure the HTTP username using “HTTP login username”.
13. Con igure the administrator password using “Community read / write”.
14. Enter “0” and return, three times to exit.
15. Connect the interSeptor to the network using a standard CAT5 straight through
cable.
NOTE: The interSeptor email alerts facility is configurable through the browser
interface only.
Configuring interSeptor on the Network
1. Make sure that you have a TCP/IP network already installed.
2. interSeptor will initially try to acquire an IP address rom the DHCP network
service, i it exists on the network, unless the “BOOTP / DHCP” option has been
disabled.
NOTE: You can run the "iupgrade.exe" program provided on the interSeptor CD-
ROM to display the interSeptor’s current P address.
3. I a DHCP network service is not available, enter the ollowing command at the
DOS prompt:
route add 172.17.XXX.ZZZ <Workstation’s P address>
NOTE: The default P address of interSeptor is 172.17.XXX.ZZZ where XXX and
ZZZ are the last two pairs of the MAC address of the interSeptor in decimal.
The MAC address can be found on the bottom of the interSeptor (e.g.
00E0XXXXXXXX).
4. Enter TELNET <interSeptor’s IP address> at the DOS prompt and press enter.
5. TELNET uses the same inter ace as serial port con iguration.
interSeptor is now installed on your network
Start your web browser, enter the interSeptor’s IP address in the address text box, and
press enter to display the home page.
Default D: interSeptor
Default Password: admin
NOTE: f the Temperature and Humidity values do not appear then please
ensure Java Runtime Environment (JRE) is up to date (www.java.com).
Alert Centre (Voice and SMS)
The Jacarta Alert Centre acility is a subscription-based service that works in
conjunction with the interSeptor to provide automatic alarm noti ication via email, SMS
and voice alarm messages (to landline or mobile phones) or up to 6 recipients.
The alerting process ensures key personnel are noti ied and the alarm acted upon via
an escalation and acknowledgment process. Easy access to change personnel details,
contact numbers, etc. is available via the Jacarta Alert Centre Login acility on
www.jacarta.com/AlertCentre/login.aspx.
To receive li e time email and telephone technical support, please register each
interSeptor at www.jacarta.com/Support/Product-Registration.aspx.
Jacarta Ltd
Wagon Yard, London Road
Marlborough, Wiltshire SN8 1LH
United Kingdom
Tel: +44(0)1672 511125
Email: [email protected]
Table of contents
Other jacarta Measuring Instrument manuals
