jbc CLUP User manual

INSTRUCTION MANUAL
Senior Tip Cleaner with
Non-Metal Brushes
CLUP
www.jbctools.com

2

Contents
1. Packing List........................................................................................ 4
2. Features .............................................................................................. 5
3. Operation........................................................................................... 6
4. Brush replacement.......................................................................... 7
5. Collection tray .................................................................................. 7
6. Brushes range................................................................................... 8
7. Maintenance ..................................................................................... 9
8. USB Connector ................................................................................. 10
9. Safety.............................................................................................. 11
10. Specications.................................................................................... 12
www.jbctools.com
3

This manual corresponds to the following reference:
CLMU-PB
1. Packing List
The following items are included:
Senior Tip Cleaner with
Non-Metal Brushes
1 unit
Non-Metal Brushes HMP
for CLU & CLR
2 units
Ref. CLMU-P2
(brushes already installed inside the cleaner)
AC Adapter
1 unit
0022529
Manual
1 unit
0027496
EU US
4

2. Features and Connections
Locking tab
Splashguard
Feet for vertical
access
Power cord
socket
ESD safe
connector
USB-B
connector
Sensors window
Switch panel
Window
www.jbctools.com
5

3. Operation
Sensor
mode
Continuous
mode
On / Off
Led status
- White: Off
- Blue: Standby
- Green: Brushes activated
- Blinking Red: Brushes jammed
For best cleaning results, we recommend placing the tip between the two brushes
for just 1 second. Longer exposure time would lead to dewetting of tip surface
causing oxidation.
If excessive pressure is applied with the tool against any of the brushes, the cleaner
stops automatically in order to protect the motors. Putting the tool out of the sensor
detection area automatically reactivates the cleaner.
CLUP is automatically switched off if the splashguard is opened during operation.
6

4. Brush Replacement
1. Pull the locking tab to open the
splashguard.
2. Pull the used up brushes out of the
cleaner by pressing its two opposite
buttons. To replace the brushes
just push them without pressing the
buttons.
5. Collection Tray
Remove the solder collection tray for
disposal of solder waste.
The tray can be removed without
disassemble the brushes.
www.jbctools.com
7

6. Brush Range
Metal Brushes
for CLU & CLR
(Black core)
Ref. CLMU-A8
Blue Metal Brushes
for CLU & CLR
(Blue core)
Ref. CLMU-A7
Non-Metal Brushes
for CLU & CLR
(Black core)
Ref. CLMU-P1
Blue Non-metal Brushes
for CLU & CLR
(Blue core)
Ref. CLMU-P7
Non-Metal Brushes HMP
for CLU & CLR
(Black core)
Ref. CLMU-P2
Blue Non-metal Brushes HMP
for CLU & CLR
(Blue core)
Ref. CLMU-P8
When changing Brushes, see the table on next page for the different brush types.
8

7. Brush Range
Metal Brushes
Ref. CLMU-A8 CLMU-A7
Type Metal Metal
Cleaning Intensive Intensive
Max. time use 10 s 10 s
Recommended
time use 1-2 s 1-2 s
Life cycle* Long Long
Core** Black Blue
Ref. CLMU-P1 CLMU-P7 CLMU-P2 CLMU-P7
Type Non-metal Non-metal Non-metal
HMP
Non-metal
HMP
Cleaning Gentle Gentle Gentle Gentle
Max. time use 5 s 5 s 5 s 5 s
Recommended
time use 1-2 s 1-2 s 1-2 s 1-2 s
Life cycle* Extended Extended Extended Extended
Core** Black Blue Black Blue
Non-Metal Brushes
Only use the non-metal Brushes when they are turning. Incorrect use will
damage them.
* When used properly, the non-metal Brushes will have a longer life than the metal ones.
** The blue core is used to distinguish it from the black core when doing lead-free and leaded
soldering.
www.jbctools.com
9

9. Maintenance
Before carrying out maintenance or storage, always unplug the equipment from the
mains.
- Use a damp cloth to clean the splashguard and the inside.
- Check periodically that the sensors window is clean. Use a cotton bud with alcohol
to clean it.
- Maintain the brushes and the solder collection tray clean.
- Replace any defective or damaged piece. Use original JBC spare parts only.
- Repairs should be performed only by a JBC authorized technical service.
Sensor Window
10