JBL Venue SUB12 User manual

Venue™Series
SUB12
Amplifier/Subwoofer
SERVICE MANUAL
JBL Consumer Products
250 Crossways Park Dr.
Woodbury, New York 11797 Rev0 7/2006

- CONTENTS -
BASIC SPECIFICATIONS……………….….….….….…………….1
PACKAGING…………………………….………………………......2
DETAILED SPECIFICATIONS ……..…………….……………..3
CONNECTIONS..……………………………………………………5
OPERATION ………….……………………………..…………….7
TEST SET-UP AND PROCEDURE……………………………….8
EXPLODED VIEW/PARTS LIST…………………………………..9
BLOCK DIAGRAM..……………………………………….…........10
120V ELECTRICAL PARTS LIST ……………………………….11
PCB DRAWINGS………………..………………………………...14
INTEGRATED CIRCUIT/TRANSISTOR PINOUTS……………..16
120V SCHEMATICS.……….…………….…………..…. ………17
BASIC SPECIFICATIONS
SUB12 Subwoofer
Frequency response: 25Hz – 150Hz
Amplifier Power output: 250W Continuous RMS power
Amplifier Peak Dynamic Power†: 500W
Crossover Frequencies 50Hz – 150Hz, 24dB/octave, continuously variable
Woofer: 12" (305mm) PolyPlas™ cone
Dimensions (including grille): 19-3/4" x 14-3/8" x 18" (502mm x 365mm x 457mm)
Weight: 39.5 lb/18kg
† The Peak Dynamic Power is measured by recording the highest center-to-peak voltage measured across the
output of a resistive load equal to minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles
on, 17 cycles off.
Occasional refinements may be made to existing products without notice but will always meet or exceed original
specifications unless otherwise stated
1
VenueSUB12

2
VenueSUB12

VENUE SUB12 150W Powered Sub/ Plate Amp
LINE VOLTAGE Yes/No Hi/Lo Line Nom. Unit Notes
US 120vac/60Hz Yes 108-132 120 Vrms Normal Operation
EU 230vac/50-60Hz Yes 207-264 230 Vrms Normal operation, MOMS required
Parameter Specification Unit QA Test Limits Conditions Notes
Amp Section
Type (Class AB, D, other) D n/a n/a
Rated Output Power (120VAC) 150 Watts 140 Domestic version only 120 VAC-60 Hz
Rated Output Power (230VAC) 150 Watts 130 EU Version only 230 VAC-50 Hz
AVG RMS Dynamic Power 250 Watts 225 Average RMS power, 3/20 Cycles 50 Hz, Driven
6dB above its input sensitivity sensitivity
THD @ Rated Power 0.3 % 122k filter 145 Watts
THD @ 1 Watt 0.1 % 0.5 22k filter
DC Offset 10 mV-DC 30 @ Speaker Outputs
Damping factor >50 DF 35 Measured at amplifier board Measured at the speaker cable. 150 Watts @
THD < 0.1 % @ 50 Hz
Input Sensitivity
Input Frequency 50 Hz 50 Nominal Freq.
L&R 240 mVrms ±2dB To 150 Watts Single input driven
LFE input 240 mVrms ±2dB To 150 Watts Single input driven, LFE switch ON
Speaker/Hi Level Input 2.4 Vrms ±2dB To 150 Watts Single input driven
Signal to Noise
SNR-A-Weighted 90 dBA 70 relative to rated power A-Weighting filter
SNR-unweighted 85 dBr 70 relative to rated power 22k filter
SNR rel. 1W-unweighted 65 dBr 60 relative to 1W Output 22k filter
Residual Noise Floor 1 mVrms 2Volume @max, using RMS reading
DMM/VOM (or A/P) BW=20 Khz. Line level inputs must be terminated using 1KOHM
Residual Noise Floor 1.5 mVrms(max) 2
Volume @max, w/ A/P Swept
Bandpass Measurement (Line
freq.+ harmonics) (BW=20 Khz) Line level inputs must be terminated using 1KOHM
Input Impedance
Line Input (L, R,LFE) 10K ohms n/a Nominal
Speaker/Hi Level Input > 4.7K ohms n/a Nominal
Filters
LP filter 4th order fixed 60-180 Hz ± 10 See AP curves 2nd order variable + 2nd order
fix-24 db/Octave
Subsonic filter (HPF) 3rd Order Fixed
LFE Low pass 2nd order 200>LP<1K Hz LFE input driven only
HP speaker out connector 200 Hz ± 10 Speaker input driven - Speaker out
loaded with 4 Ohms (Applies only to 230V Model)
Note: 120V Models do not
have speaker output 100 Hz ± 10 Speaker input driven - Speaker out
loaded with 8 Ohms (Applies only to 230V Model)
Limiter
THD at Max. Output Power n/a n/a functional Maximum Output Power Maximum THD as a result of limiting.
Features --
Volume pot Taper (lin/log) LOG -- functional A Taper
HP Speaker out 230v version functional Refer to Filter section
Phase switch 0-180 deg functional
LP Filter defeat switch YES functional Disables LP filter, intended for LFE
Input Configuration
Line In (L,R) & LFE YES -- functional Dual RCA jack
Spkr/Hi Level In YES -- functional Binding post connector L&R
Signal Sensing (ATO)
Auto-Turn-On (yes/no) YES functional
ATO Input test frequency 50 Hz functional
ATO Level LFE Input 4 mV functional Maximum acceptable level.
ATO Level Speaker in 50 mV functional Maximum acceptable level.
ATO Turn-on time 5 ms functional Amp connected and AC on, then
input signal applied
Auto Mute/ Turn-OFF Time 15 minutes 15 T before muting, after signal is
removed Auto turn of time (T) must be 5 > T < 15 Minutes
Power on Delay time 3 sec. 4AC Power Applied
3
VenueSUB12

Parameter Specification Unit QA Test Limits Conditions Notes
Transients/Pops
ATO Transient 5 mV-peak n/a @ Speaker Outputs
Turn-on Transient 50 mV-peak 2v-pp @ Speaker Outputs AC Line cycled from OFF to ON
Turn-off Transient 50 mV-peak 2v-pp @ Speaker Outputs AC Line cycled from ON to OFF
Efficiency
Efficiency 65 % 64 Nominal Line voltage 120 VAC
Stand-by Input Power 24 Watts 26 @ nom. line voltage
Maximum allowable input power under nominal
Input voltage and frequency, HOT or COLD
operation.
Power Cons. @ rated power 234 Watts 240 @ nom. line voltage 150 Watts @ 5.6 Ohms nominal line voltage
Protections
Short Circuit Protection YES functional Direct short at output Amplifier should resume operation after short
circuit condition removal
Thermal Protection YES functional @1/8 max unclipped Power at 1.06
times the input voltage
Temperature rise in accessible metal parts
should not exceed 35K rise for domestic version
or 30K rise for European versions (refer to
requirements sheet).
DC Offset Protection YES -DC present at Speaker Out leads
Design must insure no Offset at the speaker
output under any operating condition including
abnormal operation
Line Fuse Rating
USA-Domestic 2 Amps 2Type-T or Slo Blo-250 V Internal fuse with UL/SEMKO rated holder
EU 1.25 Amps 1.25 Type-T or Slo Blo-250 V, Low
Breaking capacity Internal fuse with UL/SEMKO rated holder
4
VenueSUB12

Rear Panel
CONTROLS AND CONNECTIONS
¡Subwoofer-Level Control
™LFE/Normal Selector
£Phase Switch
¢Crossover Adjustment
∞Line-Level/LFE Input
§High (Speaker)-Level Inputs
¶Power Switch
•Status LED
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CROSSOVER
FREQUENCY
LEVEL
LINE LEVEL IN
PHASE
Min Max
L
R
L R
For LFE use L or R
Green: On
Red: Standby
+ –
50Hz
0º
80Hz
150Hz
POWER
ON
¡
£
¢
∞
§
•
™
LFE NORMAL
180º
HIGH
LEVEL
IN
¶
120V
60Hz
OFF
WARNING: TO REDUCE THE RISK OFFIRE OR ELECTRICAL
SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
AVERTISSEMENT: POUR PRÉVENIR LES RISQUES D'INCENDIE OU DE CHOC
ÉLECTRIQUE, ÉVITER D'EXPOSER CET APPAREILALA PLUIE OU A L'HUMIDITÉ.
NRTL/C
CSA 22.2
UL1492
JBL Venue
SUB12
Venue Sub OM 1/27/06 9:26 AM Page 6
5
VenueSUB12

SYSTEM CONNECTIONS
If you have a Dolby®Digital or DTS®receiver/processor with a
low-frequency-effects (LFE) or subwoofer output: If your receiver/processor does not have subwoofer outputs
for the left and right channels or an LFE output, connect
speaker wire from your receiver/amplifier to your speakers
and subwoofer using two sets of speaker wire:
5
If your receiver/processor does not contain a Dolby Digital
or DTS processor, but has subwoofer outputs:
Set line-level/LFE switch to
“Normal.”
NOTE: If your receiver/processor
has only one sub out, you may
use either the L or R input.
CROSSOVER
FREQUENCY
LEVEL
LINE LEVEL IN
PHASE
Min Max
L
R
LR
For LFE use Lor R
LFE NORMAL
HIGH
LEVEL
IN
50Hz
0º 180º
150Hz
RECEIVER/AMPLIFIER
Front Speaker Output
80Hz
Green: On
Red: Standby
PS-10/PS-12
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
120V
60Hz
CROSSOVER
FREQUENCY
LEVEL
LINE LEVEL IN
PHASE
Min Max
L
R
L R
For LFE use Lor R
LFE NORMAL
HIGH
LEVEL
IN
+ –
50Hz
0º180º
150Hz
POWER
ON OFF
RECEIVER/PROCESSOR
80Hz
L R
Green: On
Red: Standby
PS-10/PS-12
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
120V
60Hz
CROSSOVER
FREQUENCY
LEVEL
LINE LEVEL IN
PHASE
Min Max
L
R
LR
For LFE use L or R
LFE NORMAL
HIGH
LEVEL
IN
L
R
HIGH
LEVEL
OUT
+ –
50Hz
0º180º
150Hz
POWER
ON OFF
SUBWOOFER OR
LFE OUTPUT
80Hz
Green: On
Red: Standby
Set LFE/Normal switch to “LFE.”
This figure shows how to connect bare wires to the terminals.
Venue Sub OM 1/27/06 9:26 AM Page 7
6
VenueSUB12

Power On
Plug your subwoofer’s AC cord into a wall outlet. Do not use the outlets on the
back of the receiver.
Initially set the Subwoofer-Level Control ¡to the “min” position.
Turn on your sub by pressing the Power Switch ¶on the rear panel.
Turn on your entire audio system and start a CD or movie soundtrack at a
moderate level.
Auto On/Standby
With the Power Switch ¶in the ON position, the Status LED •on the
back panel will remain lit in red or green to indicate the On/Standby mode
of the subwoofer.
RED = STANDBY (No signal detected, Amp Off)
GREEN = ON (Signal detected, Amp On)
The subwoofer will automatically enter the Standby mode after approximately
10 minutes when no signal is detected from your system. The subwoofer will
then power ON instantly when a signal is detected. During periods of normal
use, the Power Switch ¶can be left on. You may turn off the Power Switch
¶for extended periods of nonoperation, e.g., when you are away on vacation.
Adjust Gain
Turn your Subwoofer-Level Control ¡up to the halfway position. If no sound
emanates from the subwoofer, check the AC-line cord and input cables. Are the
connectors on the cables making proper contact? Is the AC plug connected to
a“live” receptacle? Has the Power Switch ¶been pressed to the “On” posi-
tion? Once you have confirmed that the subwoofer is active, proceed by play-
ing a CD, record or cassette. Use a selection that has ample bass information.
Set the overall volume control of the preamplifier or stereo to a comfortable
level. Adjust the Subwoofer-Level Control ¡until you obtain a pleasing blend
of bass. Bass response should not overpower the room but rather be adjusted
so there is a harmonious blend across the entire musical range. Many users
have a tendency to set the subwoofer volume too loud, adhering to the belief
that a subwoofer is there to produce lots of bass. This is not entirely true. A
subwoofer is there to enhance bass, extending the response of the entire sys-
tem so the bass can be felt as well as heard. However, overall balance must
be maintained or the music will not sound natural. An experienced listener will
set the volume of the subwoofer so its impact on bass response is always
there but never obtrusive.
Phase Control
The Phase Switch £determines whether the subwoofer speaker’s pistonlike
action moves in and out with the main speakers, 0˚, or opposite the main
speakers, 180˚. Proper phase adjustment depends on several variables such
as room size, subwoofer placement and listener position. Adjust the phase
switch to maximize bass output at the listening position.
Crossover Adjustment
The Crossover Adjustment Control ¢determines the highest frequency at
which the subwoofer reproduces sounds. If your main speakers can comfortably
reproduce some low-frequency sounds, set this control to a lower frequency
setting, between 50Hz and 100Hz. This will concentrate the subwoofer’s
efforts on the ultradeep bass sounds required by today’sfilms and music.
If you are using smaller bookshelf speakers that do not extend to the lower
bass frequencies, set the Crossover Adjustment control to a higher setting,
between 120Hz and 150Hz.
NOTE: This control will have no effect if the LFE/Normal Selector ™is set
to LFE. If you have a Dolby Digital or DTS processor/receiver, the Low-Pass
Frequency is set by the processor/receiver. Consult your owner’s manual
to learn how to view or change this setting.
The enclosure may be cleaned using a soft cloth to remove fingerprints or to
wipe off dust.
The grille may be gently vacuumed. Stains may be removed with an aerosol
cleaner, following its instructions. Do not use any solvents on the grille.
All wiring connections should be inspected and cleaned or remade periodically.
The frequency of maintenance depends on the metals involved in the connections,
atmospheric conditions and other factors, but once per year is the minimum.
If a problem occurs, make sure that all connections are properly made and
clean. If a problem exists in one loudspeaker, reverse the connection wires to
the left and right system. If the problem remains in the same speaker, then the
fault is with the loudspeaker. If the problem appears in the opposite speaker,
the cause is in another component or cable. In the event that your subwoofer
ever needs service, contact your local JBL dealer or visit www.jbl.com for
aservice center near you.
OPERATION MAINTENANCE AND SERVICE
Venue Sub OM 1/27/06 9:26 AM Page 8
7
VenueSUB12

SUB12 Test Set Up and Procedure
Equipment needed:
•Function/signal generator/sweep generator
•Integrated Amplifier
•Multimeter
•Speaker cables
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect line level (RCA) cables to the Subwoofer Line Level Input jacks L/R on
the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs.
2) Turn the CROSSOVER control to maximum (150).
3) Turn the LEVEL control on the UUT to completely counterclockwise (MIN).
4) Phase switch position = does not matter; LFE/Normal switch should be on NORMAL
5) Turn on generator; adjust to 150mV, 50 Hz.
6) Plug in UUT; turn the power switch ON. LED should switch from Red to Green.
7) Turn LEVEL control full clockwise (MAX); immediate and vigorous bass response should be heard and felt
from port tube opening on the bottom.
8) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable.
9) Connect one pair of speaker cables to Speaker Level input terminal (IN) on UUT. Cables should be
connected to an integrated amplifier fed by the signal generator.
10)Turn on generator and adjust so that speaker level input at the amplifier is 3.3V, 50 Hz. Turn LEVEL control
full clockwise (MAX).
11)Green LED should light; immediate and vigorous bass response should be heard and felt from the port
tube opening.
Sweep Function
1) Follow steps 8-10 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet (instructions on exploded view drawing); detach + and - wire clips.
2) Check DC resistance of woofer; it should be 4.8 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier
fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
8
VenueSUB12

9
VenueSUB12

10
VenueSUB12

SUB12 120V Electrical parts list
Part numbe
r
Description Qt
y
Reference Desi
g
nato
r
MAIN/PREAMP PC
B
Resistors
021-220202-120Z
S
MOF resistor 22R 2W(S) J MB TY 1 R10
021-120403-020Z
S
GS MOF Resisto
r
1K2 3WS J 8x20 Kin
k
1R9
021-120405-020Z
S
GS MOF Resisto
r
1K2 5WS J 8x25 Kin
k
1R6
024-000098-120Z
S
GS SMD Resisto
r
0R 1/8W J 0805 2 R125,126
024-100398-120Z
S
GS SMD Resisto
r
100R 1/8W J 0805 1 R62
024-100598-120Z
S
GS SMD Resisto
r
10K 1/8W J 0805 13 R17,19,37,54,58,63,71,72,111,123,124,20,21
024-100698-120Z
S
GS SMD Resisto
r
100K 1/8W J 0805 4 R22~25
024-100898-120Z
S
GS SMD Resisto
r
10M 1/8W J 0805 1 R121
024-120698-120Z
S
GS SMD Resisto
r
120K 1/8W J 0805 1 R39
024-121598-100Z
S
GS SMD Resisto
r
12K1 1/8W F 0805 1 R38
024-137698-100Z
S
GS SMD Resisto
r
137K 1/8W F 0805 1 R32
024-150498-120Z
S
GS SMD Resisto
r
1K5 1/8W J 0805 T 2 R67,68
024-180598-120Z
S
GS SMD Resisto
r
18K 1/8W J 0805 T 1 R29
024-187698-100Z
S
GS SMD Resisto
r
187K 1/8W F 0805 1 R45
024-220498-121Z
S
GS SMD Resisto
r
2K2 1/8W J 0805 T 1 R61
024-237598-120Z
S
GS SMD Resisto
r
23K7 1/8W F 0805 1 R48
024-243698-100Z
S
GS SMD Resisto
r
243K 1/8W F 0805 1 R36
024-270498-120Z
S
GS SMD Resisto
r
2K7 1/8W J 0805 T 1 R64
024-300398-120Z
S
GS SMD Resisto
r
300R 1/8W J 0805 1 R55
024-300598-120Z
S
GS SMD Resisto
r
30K 1/8W J 0805 T 1 R56
024-330498-120Z
S
GS SMD Resisto
r
3K3 1/8W J 0805 T 5 R12-15,59
024-332498-100Z
S
GS SMD Resisto
r
3K32 1/8W F 0805 2 R26,27,
024-360498-120Z
S
GS SMD Resisto
r
3K6 1/8W J 0805 T 1 R28
024-453598-100Z
S
GS SMD Resisto
r
45K3 1/8W F 0805 1 R30
024-470598-120Z
S
GS SMD Resisto
r
47K 1/8W J 0805 T 3 R44,47,49
024-470698-120Z
S
GS SMD Resisto
r
470K 1/8W J 0805 1 R70
024-470798-120Z
S
GS SMD Resisto
r
4M7 1/8W J 0805 T 1 R60
024-487498-100Z
S
GS SMD Resisto
r
4K87 1/8W F 0805 2 R51,53
024-510398-120Z
S
GS SMD Resisto
r
510R 1/8W J 0805 1 R57
024-560598-120Z
S
GS SMD Resisto
r
56K 1/8W J 0805 T 1 R122
024-620398-100Z
S
GS SMD Resisto
r
620R 1/8W F 0805 2 R16,18
024-680498-120Z
S
GS SMD Resisto
r
6K8 1/8W J 0805 T 5 R46,40,41,43,4
2
024-680598-120Z
S
GS SMD Resisto
r
68K 1/8W J 0805 T 4 R33,34,31,
5
024-820598-120Z
S
GS SMD Resisto
r
82K 1/8W J 0805 T 1 R69
024-330598-120Z
S
GS SMD Resisto
r
33K 1/8W J 0805 T 2 R4,5
024-330498-120Z
S
GS SMD Resisto
r
3K3 1/8W J 0805 T 2 R7,8
020-220497-120Z
S
GS film resistor 2K2 1/4W J 1 R11
021-100401-120Z
S
GS MOF resistor 1K 1W J Kink 1 R103
022-500003-020Z
S
GS Resistor KNP 0R05 3WS J FK TYP 1 R104
024-100298-120Z
S
GS SMD resistor 10R 1/8W J 0805 T 2 R81,82
024-100498-120Z
S
GS SMD resistor 1K 1/8W J 0805 TA 8 R79,83,92,95,96,105,108,11
0
024-100598-120ZS GS SMD resistor 10K 1/8W J 0805 T 19 R2,74,75,84,88,89,97,106,109,113-117,119,
120,138,139,141
024-100698-120Z
S
GS SMD resistor 100K 1/8W J 0805 2 R3,112,
024-110598-100Z
S
GS SMD resistor 11K 1/8W F 0805 T 1 R98
024-200598-120Z
S
GS SMD resistor 20K 1/8W J 0805 T 1 R94
024-220398-120Z
S
GS SMD resistor 220R 1/8W J 0805 1 R90
024-220498-121Z
S
GS SMD resistor 2K2 1/8W J 0805 T 2 R1,87
024-220598-120Z
S
GS SMD resistor 22K 1/8W J 0805 T 1 R118
024-220798-120Z
S
GS SMD resistor 2M2 1/8W J 0805 T 1 R80
024-270498-120Z
S
GS SMD resistor 2K7 1/8W J 0805 T 1 R73
024-390498-120Z
S
GS SMD resistor 3K9 1/8W J 0805 T 1 R93
024-390598-120Z
S
GS SMD resistor 39K 1/8W J 0805 T 1 R77
024-430498-100Z
S
GS SMD resistor 4K3 1/8W F 0805 T 1 R78
024-470298-120Z
S
GS SMD resistor 47R 1/8W J 0805 T 2 R101,102
024-470398-120Z
S
GS SMD resistor 470R 1/8W J 0805 3 R76,99,100
024-470498-120Z
S
GS SMD resistor 4K7 1/8W J 0805 T 2 R85,86
024-470598-120Z
S
GS SMD resistor 47K 1/8W J 0805 T 1 R107
024-560498-120Z
S
GS SMD resistor 5K6 1/8W J 0805 T 1 R140
11
VenueSUB12

Part numbe
r
Description Qt
y
Reference Desi
g
nato
r
024-680498-120Z
S
GS SMD resistor 6K8 1/8W J 0805 T 1 R91
026-200595-269Z
S
GS VR 20k x 2 CROSSOVE
R
PN:RD163121R03D-
2
1 VR2
026-500495-005Z
S
GS VR 5K LEVE
L
PN:RD163111R22B-
5
1 VR1
Semiconductor
s
054-414803-100Z
S
GS SMD DIODE PN:LL4148 MINI-ME 15 D3,4,10~22
051-005600-100Z
R
GR Transistor PNP PN:MPSW56RLRAR TO 1 Q3
054-045580-100Z
S
GS SMD IC:(Dual Op-amp) PN:NJM4558M-TE3-* 1 U4
054-007200-100Z
R
GR SMD IC (Dual Op-amp) PN:TL072CDR SO-
8
1U5
050-505200-001Z
S
GS LED PN:LT-2402-21 1
054-000100-100Z
S
GS SMD DIODE PN:ES1D 200V 1A 2 D38,39
054-008407-000Z
R
GR SMD ZENER DIODE 15V, 0.35W PN:BZX84C15-7-F
S
3 D6,7,9
051-003100-000Z
S
GS Transistor NPN PN:TIP 31C TO-220 1 Q4
052-400080-000Z
R
GR Bridge Rectifie
r
PN:RS804 400V,8
A
1 BR1
054-540100-100Z
R
GR SMD Transistor PNP PN:MMBT5401 LT1
S
2 Q24,26
054-033904-100Z
R
GR SMD Transisto
r
PN:MMBT3904LT1G
S
5 Q5~9
054-007400-100Z
R
GR SMD IC:(Quad Op-amp
)
PN:TL074CDR 2 U2,3
054-011400-100Z
R
GR SMD Transisto
r
PN:DTC114TKA SMT
3
1Q7
051-000600-100Z
R
GR Transistor NPN PN:MPSW06RLRA TO- 2 Q2,Q16
051-222200-100Z
R
GR Transistor NPN (ON PN:MPS2222ARLRA
R
1 Q21
051-290700-100Z
R
GR Transistor PNP (ON PN:MPS2907A RLRA
R
2 Q19,23
051-540101-000Z
R
GR Transistor PNP(FAI PN:2N5401 TO-92
T
1Q1
051-555100-000Z
R
GR Transistor NPN PN:2N5551 TO-92
T
1 Q17
051-640001-000Z
R
GR MOSFET N-Chann PN:IRF640NPBF TO
-
2 Q18,22
053-211100-000Z
R
GR IC:DIP,DRIVE
R
PN:IR2111 8PIN (I 1 U7
054-000100-100Z
S
GS SMD DIODE: PN:ES1D 200V 1A
T
4 D5,26,29,33
054-007200-100Z
R
GR SMD IC (Dual Op-amp) PN:TL072CDR SO-
8
2 U6,8
054-008406-000Z
R
GR SMD ZNR DIODE 10V 350MW )PN:BZX84C10-7-F S 1 D35
054-008408-000Z
R
GR SMD ZNR DIODE 5.6V 350MW PN:BZX84C5V6-7-
F
3 D24,36,37
054-033904-100Z
R
GR SMD (TRANSISTOR
)
PN:MMBT3904LT1G
S
3 Q11,14,13
054-033906-100Z
R
GR SMD Transistor (ON) PN:MMBT3906LT1G
S
3 Q10,12,15
054-414803-100Z
S
GS SMD DIODE: PN:LL4148 MINI-ME 10 D1,2,23,27,28,30-32,34,4
4
054-540100-100Z
R
GR SMD Transistor PNP PN:MMBT5401 LT1
S
3 Q20,24,26
054-555100-100Z
R
GR SMD Transistor (NPN PN:MMBT5551 LT1
R
1 Q25
Capacitor
s
039-100384-100Z
R
GR Safety Capacitor 0u1/250
V
PN:HQX0.1K275VAC
x
1 CXAC1
034-100525-300Z
S
GS Elect. Cap. 10uF/25V M (R)051 1 C35
034-220525-301Z
S
GS Elect. Cap. 22uF/25V M (R)5x1 4 C4,9,41,39,
031-100244-100Z
S
GS SMD Ceramic cap. 0u01/50V K 0805 X 7R 3 C33,5,10
031-100343-100Z
S
GS SMD Cap. 100pF/50V J 0805 NPO 2 C36,16
031-100344-100Z
S
GS SMD Cap. 0u1/50V K 0805 X7R 1 C11
031-100384-100RZ
S
GS SMD Cap. 0u1/250V K 1206
X
2 C3,7
031-220344-100Z
S
GS SMD Cap. 220pF/50V J 0805 NPO 4 C20,21,19,1
031-330444-300Z
S
GS SMD Cap. 3300pF/50V K 0805 X7R 2 C40,34
034-220525-301Z
S
GS Elect. Cap. 22uF/25V M (R)5x1 4 C4,9,41,39
034-330615-300Z
S
GS Elect. Cap. 330uF/16V M (R)0
8
1 C12
034-330780-300Z
R
GR Electrolytic cap. 85℃3300uF/80V M (R)2 2 C6,8
034-470415-301Z
S
GS Elect. Cap. 4u7/50V M (R)0511 1 C2
034-470515-200Z
R
GR Electrolytic cap. 47uF/16V M (R)051 1 C37
038-100363-300Z
R
GR MPE Cap. P:5 0u1/100V J 5 C26,27,28,29,3
0
038-150393-300Z
R
GR MPECap. P:5 0u15/63V J 1 C25
038-330393-300Z
R
GR MPE Cap. P:5 0u33/63V J 1 C31
032-100484-200Z
S
GS END Mylar cap. 1uF/250V K P:1
5
1 C70B
031-100244-100Z
S
GS SMD Ceramic cap. 0u01/50V K 0805
X
4 C45,51,66,6
7
031-100343-100Z
S
GS SMD Cap. 100pF/50V J 080
5
1 C58
031-100344-100Z
S
GS SMD cap. 0u1/50V K 0805 X
7
17 C42-44,46-49,52,54,55,60,63,71,74,77,82,81
031-470244-102Z
S
GS SMD cap. 0u047/50V K 080
5
2 C62,59
031-560243-100Z
S
GS SMD cap. 56pF/50V J 0805 N 2 C57,61
031-560343-102Z
S
GS SMD cap. 560pF/50V J 080
5
1 C56
032-100484-200Z
S
GS END Mylar cap. 1uF/250V K P:1
5
1 C70
033-470444-270Z
S
GS NPE cap. 印ELY
T
4u7/50V K10 (R)8
x
1 C73
033-680464-270Z
S
GS NPE cap.印ELY
T
6u8/100V K10 (R)1 1 C72
034-100625-300Z
S
GS Electrolytic cap. 100uF/25V M (R)6. 1 C64
12
VenueSUB12

Part numbe
r
Description Qt
y
Reference Desi
g
nato
r
034-220525-301Z
S
GS Electrolytic cap. 22uF/25V M (R)5x1 2 C50,53
034-330525-300Z
R
GR Electro. Cap. 33uF/25V M (R)051 1 C1
034-330615-300Z
S
GS Electrolytic cap. 330uF/16V M (R)0
8
1 C78
034-470515-307Z
R
GS Electrolytic cap. LOW ES 47uF/16V M (R)0
5
1 C65
038-100363-300Z
R
GR MPE cap. P:5 0u1/100V J 2 C68,69
Miscellaneou
s
041-115001-000Z
R
GR BEAD COIL PN:YT-10911 1 L5
043-300101-000Z
R
GR INDUCTO
R
PN:YT-10033 30uH 1 L2
043-560200-000Z
R
GR INDUCTO
R
56uH YT-1077
9
1L1
043-700101-000Z
R
GR TOROIDAL INDUC 70uH YT-1068
2
1L3
025-010300-000Z
R
GR Thermiste
r
PN:NTSE103KZ072
K
1 TH1,
044-100100-000Z
S
GS SMD FERRITE BE PN:321611 600R/1
0
2 FB1,FB2
061-700044-000Z
R
GR Mica 13x18mm TO-220無3
063-010012-000Z
R
GR Bracket for Transistor P/N:TRK-1 4
074-300018-000Z
R
GR RELA
Y
1
073-032315-601Z
S
GS Heatsin
k
1
072-040064-000Z
R
GR Terminal (PCB TYPE) PC250 (t=0.8m/m) S+)
077-100102-100Z
R
GR Connecto
r
PN:JS-1001-02 P=2 1 CONN3
A
GR Terminal (PCB TYPE) PC205 (t=0.8m/m) S-)
043-324300-000Z
R
GR INDUCTO
R
324uH YT-1077
8
1L4
MISCELLANEOUS/MECHANICA
L
061-020000-000Z
S
GS Knob ABS HTS-1 φ20x15m/m UL94V
-
2 Level, crossove
r
074-030002-000Z
R
GR TOGGLE SW PN:L101-T2B4QE
(
點2 SW5,SW6
061-400014-000BZ
R
GR RUBBER FOO
T
ID:6.2 OD:11.5 t= 4 for Transforme
r
072-040096-000Z
R
GR T187MA(PCB (t=0.8mm) PC187(0 7 AC1,AC3,T1,
086-021818-005Z
R
GR Power Cord NIS 2L=1830mm 105C+T1
8
1
093-105202-300Z
R
GR FUSE:UL GSL(2
A
FUSE:2A,250V,5*2
0
1F1
072-060170-000Z
R
GR B.P Binding post se
t
2 BP/IP
073-050001-000Z
S
GS FUSE CLIP P/N:CT-FH1206 2 for F1
074-020018-000Z
R
GR ROCKER SW (Power) PN:RF1003-BB4-
0
1
072-010058-000ZR RCA jacks Dual 1 CONN1
042-010053-003Z
R
GR Transformer, Main 120
v
YT-10616-4 1
063-321101-000Z
R
Plastic Panel 322x105.7x15mm B
L
1
063-531808-000Z
R
Plastic Bucket 322x105.7x146.5m
m
1
008-060303-042Z
R
GR GASKET 25.4x25.4x38mmPO
R
1 for X'former
008-061215-000Z
R
GR GASKET C430
5
12x15 t=5mm CR 1 for Thermister
008-062002-002Z
R
GR GASKET (PB10/12
)
PN:L-32 200x20m
m
1
008-062002-012Z
R
GR GASKET (PB10/12
)
200x20mm t=2mm C
R
1 COVE
R
底
008-063208-000Z
R
GR GASKET C430
5
321x8 t=1mm CR 2 COVERx2
008-069304-000Z
R
GR GASKET C430
5
93x4 t=1mm CR 2 COVERx2
13
VenueSUB12

14
VenueSUB12

15
VenueSUB12

16
VenueSUB12

音 律 電 子 股 份 有 限 公 司
17
Venue SUB12

18
Venue SUB12