Jefferson JEFTRCH24 User manual

Compact and lightweight for easy portability
Constructed from tough and durable ABS thermoplastic
140° reex angle for easy adjusting and enhanced functionality
Three working modes: High, Low, SOS On/Off Flash
Magnetic base allows for hands-free usage
Built-in Lithium-ion rechargeable battery
Battery life indicator light bar
FEATURES
www.jeffersontools.com
User Manual
v.1.1
JEFTRCH24
1. SAFETY
WARNING! Use only the supplied mains
charger. Failure to comply with this instruction
could cause injury or cause a re, and will
invalidate the warranty.
WARNING! It is the user’s responsibility
to read, understand and comply with the
following electrical instructions:
• Inspect the charger plug, cable and
connector for damage before connecting
to the mains power supply to ensure
it is safe to use.
• Ensure the inspection lamp is fully charged
before initial use.
• Do not expose the light to damp or wet
conditions whilst charging.
• Do not handle, move or turn the inspection
lamp on during the charging period.
• Avoid shining the light in the direction of
another person’s or an animal’s eyes.
• Keep away from children.
• If the battery or the inspection lamp casing
is damaged, do not use.
• Charge before use and recharge the battery
pack every 3 months if it is not being used
for a long time. Always recharge the
battery after used.
• Do not open, disassemble, modify or
service the battery.
• Replace only with the correct battery
for this product.
• Recycle or dispose of used battery as
stipulated by local regulation.
• If the electrolyte in the cells gets on
your skin, thoroughly wash with
soap and water. If it gets in your eyes,
rinse thoroughly with cool water and seek
immediate medical attention.
JEFTRCH24
COB LED RECHARGEABLE
MULTI-FUNCTIONAL
INSPECTION
LAMP
2. CHARGING & BATTERIES
WARNING! Ensure the correct rechargeable
batteries are installed before charging.
• Insert USB cable into mains plug and plug
into mains supply.
• Remove USB socket cover on side of
main body of inspection lamp.
• Connect the USB lead to the port on the
side of the main body and a USB power
socket (see g 1).
Turn on the power supply.
• When charging has completed all four light
bars will illuminate to indicate
that the batteries have fully charged.
Turn off the power supply and remove
charging lead and replace socket cover.
INSTALLING BRC 18650 BATTERIES
Installing 2 x BRC 18650 batteries
• Twist the base of the inspection lamp in a
clockwise direction until the base complete
detaches from the body.
• Insert 2 x BRC 18650 batteries into the
allocated battery slot ensuring the polarity
is matching the polarity indicated on the
battery compartment (g.2).
• Re-attach the battery compartment by
twisting the base unit in a clockwise
direction until it is fully tightened.
RUNNING
TIME
USB
RECHARGEABLE
CHARGING TIME
Fig.1
1000
3.5 HRS
4.5 HRS
1000 LUMENS
BEAM
RANGE
Fig.2
Fig.3
The worklight is operated via the
ON/OFF switch (Fig 3)
1 Press once for high beam
2 Press twice for low beam
3 Press three times for SOS ashing light
4 Press four times for quick strobe light
5 Press fth time to switch off
3. OPERATION
WARNING! Ensure the
correct rechargeable
batteries are installed
before attaching the
USB recharging cable
WARNING! Ensure the
correct rechargeable
batteries are installed
before attaching the
USB recharging cable
+
-

Jefferson Professional Tools & Equipment, or hereafter “Jefferson” warrants its customers that
its products will be free of defects in workmanship or material. Jefferson shall, upon suitable
notication, correct any defects, by repair or replacement, of any parts or components of this
product that are determined by Jefferson to be faulty or defective.
This warranty is void if the equipment has been subjected to improper installation, storage,
alteration, abnormal operations, improper care, service or repair.
Warranty Period
Jefferson will assume both the parts and labour expense of correcting defects during the
stated warranty periods below.
All warranty periods start from the date of purchase from an authorised Jefferson dealer. If
proof of purchase is unavailable from the end user, then the date of purchase will be deemed
to be 3 months after the initial sale to the distributor.
1 Year
• Jefferson 1000 Lumens COB LED Rechargeable Multi-Functional Inspection lamp
(JEFTRCH24).
90 Days
• All replacement parts purchased outside of the warranty period
Important: All parts used in the repair or replacement of warranty covered equipment will be
subject to a minimum of 90 days cover or the remaining duration of the warranty period from
the original date of purchase.
Warranty Registration / Activation
You can register and activate your warranty by visiting the Jefferson Tools website using the
following address:
www.jeffersontools.com/warranty and completing the online form.
Online warranty registration is recommended as it eliminates the need to provide proof of
purchase should a warranty claim be necessary.
Warranty Repair
Should Jefferson confirm the existence of any defect covered by this warranty the defect will
be corrected by repair or replacement at an authorized Jefferson dealer or repair centre.
Packaging & Freight Costs
The customer is responsible for the packaging of the equipment and making it ready for
collection. Jefferson will arrange collection and transportation of any equipment returned under
warranty. Upon inspection of the equipment, if no defect can be found or the equipment is not
covered under the terms of the Jefferson warranty, the customer will be liable for any labour
and return transportation costs incurred. These costs will be agreed with the customer before
the machine is returned.
NOTE: * Jefferson reserve the right to void any warranty for damages identified as being
caused through misuse *
Warranty Limitations
Jefferson will not accept responsibility or liability for repairs made by unauthorised technicians
or engineers. Jefferson’s liability under this warranty will not exceed the cost of correcting the
defect of the Jefferson products.
Jefferson will not be liable for incidental or consequential damages (such as loss of business
or hire of substitute equipment etc.) caused by the defect or the time involved to correct the
defect. This written warranty is the only express warranty provided by Jefferson with respect to
its products.
Any warranties of merchantability are limited to the duration of this limited warranty for the
equipment involved.
Claiming Warranty Coverage
The end user must contact Jefferson Professional Tools & Equipment:
(Tel: [phone]) or their nearest authorised Jefferson dealer where final
determination of the warranty coverage can be ascertained.
Step 1 - Reporting the Defect
Online Method:
Visit our website www.jeffersontools.com/warranty and complete the Warranty Returns form.
You can complete the form online and submit it to us directly or download the form to print out
and return by post.
Telephone Method:
Contact your Jefferson dealer or sales representative with the following information:
• Model number
• Serial number (usually located on the specification plate)
• Date of purchase
A Warranty Returns form will be sent to you for completion and return by post or fax, together
with details of your nearest authorised Jefferson repair centre. On receipt of this form Jefferson
will arrange to collect the equipment from you at the earliest convenience.
Step 2 - Returning the Equipment
It is the customer’s responsibility to ensure that the equipment is appropriately and securely
packaged for collection, together with a copy of the original proof of purchase. Please note
that Jefferson cannot assume any responsibility for any damage incurred to equipment during
transit. Any claims against a third party courier will be dealt with under the terms & conditions
of their road haulage association directives.
NOTE: Jefferson will be unable to collect or process any warranty requests without a copy of
the original proof of purchase.
Step 3 - Assessment and Repair
On receipt, the equipment will be assessed by an authorised Jefferson engineer and it will
be determined if the equipment is defective and in need of repair and any repairs needed are
covered by the warranty policy. In order to qualify for warranty cover all equipment presented
must have been used, serviced and maintained as instructed in the user manual.
Where repair is not covered by the warranty a quotation for repair, labour costs and return
delivery will be sent to the customer (normally within 7 working days). Note: If the repair
quotation is not accepted Jefferson Professional Tools & Equipment will invoice 1 hour labour
time at £30 per hour plus return carriage costs (plus VAT).
In cases where no fault can be found with the equipment, or, if incorrect operation of the
equipment is identified as the cause of the problem, a minimum of 1 hour labour at £30 per
hour plus carriage costs will be required before the equipment will be despatched back to the
customer.
Any equipment repaired or replaced under warranty will normally be ready for shipment back to
the customer within 7 working days upon receipt of the equipment at an authorised Jefferson
Repair centre (subject to part availability). Where parts are not immediately available Jefferson
will contact you with a revised date for completion of the repair.
General Warranty Enquiries
For any further information relating to Jefferson warranty cover please call:
[phone] or send your enquiry via email to [email protected]
Disclaimer:
The information in this document is to the best of our knowledge true and accurate, but all
recommendations or suggestions are made without guarantee. Since the conditions of use are
beyond their control, Jefferson Tools® disclaim any liability for loss or damage suffered from
the use of this data or suggestions. Furthermore, no liability is accepted if use of any product
in accordance with this data or suggestions infringes any patent. Jefferson Tools® reserve the
right to change product specifications and warranty statements without further notification. All
images are for illustration purposes only.
LIMITED WARRANTY STATEMENT
www.jeffersontools.com
User Manual
v.1.1
EC DECLARATION OF CONFORMITY
We, Jefferson Professional Tools & Equipment, as the authorised European Community representative of
the manufacturer, declare that this equipment conforms to the requirements of the following Directives:
Name and address of manufacturer
or authorised representative:
Jefferson Tools, Herons Way, Chester Business Park,
Chester, United Kingdom, CH4 9QR
Telephone: [phone]
Fax: [phone]
Email: [email protected]
www.jeffersontools.com
2014/30/EU - Electromagnetic compatibility
Signed By: Stephen McIntyre Date: 26th June 2019
JEFTRCH24