Jenn-Air CVEX4100 Series User manual

rINSTALLATION
INSTRUCTIONS ExpressionsConvertible ,_=JENN..AIR
CooktopSenes [ wE600_,_,REET_H,_
Models CVEX4100, CVEX4270 & CVEX4370
IMPORTANT
•InstallationshouldbeperformedbyaJenn-Airauthorizedservicerorotherqualifiedinstaller.
•ReadSafetyPrecautionsintheUse&Caremanualbeforeusingthisappliance.
INSTALLER
•Saveinstallationinstructionsforlocalelectricalinspector'suse.
•Leaveinstallationinstructionswiththeappliance,
CONSUMER
•Retaininstallationinstructionswiththeappliance.
_ay berotatedforhorizontal
orverticaldirectionby loosening
nutsaroundblowerinlet.Accessible
insideventilationchamber.
I
g20_"-+ 1/16" +_1/16"or + .16cm
52.23 cm + .16cm A Cul_ut 8"
Cutout 20.30cm
2Y8"
5.40 cm _,°
IMPORTAN"
CUTOUT
DIMENSIONS
No_sARE CRITICAL
A B C D E
CUTOUT CUTOUT DUCT DUCT MIN. CABINET
WIDTH DEPTH OPENING OPENING WIDTH
inches cm inches cm inches cm inches cm inches cm
SingleBay 18 11116 47.48 20 9/16 52.23 6 916 16.03 147/16 36.67 21 53.34
DoubleBay 307/16 77.34 20 9/16 52.23 17 3/4 45.08 147/16 36.67 33 83.82
Triple Bay 41 31/32 160.60 209/16 52.23 173/4 45.08 147/16 36.67 45 114.30 8101P414-60
(lo-ol-oo)

SINGLE
See side clearance )1 I<----
notebelow.TT__-'_ 314,
Clearance/ IIn _
Required,_ I LI I _ _-_"t-
171/2"[ I I] 1"-1-3 Grease /
44.460m/I II I I I , ContainerKSEE NOTE
/ I II I LI I BELOW
J"12 1i2"-_1BELOW
31.76 cm
DOUBLE
See side clearance )J 1(--i 14J-J#4c
note below, r $
I. m
.,n [] --LEp--
I
Clearance_ 1"
Required .,_11 7/16"--_.- _ L
17 1/2"29.06 cm KSEE NOTE
44.46 cm BELOW
,JSEE NOTE
[.( 12 1/2_--,-BELOW
31.76 cm
TRIPLE
See side clearance ) I _
note below. -- "l" t- '4 3/4"
I L 12.01 cm J,
Min. T
Clearancet
Required KSEE NOTE
171/2_ 29"06cm _ I__BELOW
44.46cm J SEE NOTE
BELOW
I_ 30 1/8" "
76.52 cm
Instructions For Installer:
• Save installation instructions for local inspector's use.
• Leave installation instructions with the appliance.
• Refer to "Installer Installation Suggestions" on page 3 before cutting.
•Dimensions shown in both inchesand centimeters.
•Consult ducting guidefor proper instruction.
•Dimensions "A"&"B"-tolerances +/-1/16"or +/-,16 cm.
•Dimension "J"-provide2"min, (5.08 cm) cabinet clearancetomotor for cooling purpose.
NOTE:Wherepossible, 6"(15,24 cm) is recommended formotor blower service.
•Dimension "K"-provide 6-1/4"(15.88 cm) requiredfor removalof(supplied) greasecontainer(s).
Installed dimension for(supplied) greasecontainer(s)is 5-1/2"(13.97 cm),
•Side Clearance - grills installed near a side wall must allowa minimum clearance of 6"(15.24 cm) between cooktop
and sidewall for maximum performance. Minimum clearance of 1" (2.54 cm) is required to sidewalls and 314"
(1.905 cm) to rear wall.
• Electrical Hookup - the unit must be properly circuit protected and wired according to local electricalcodes.See
electrical wiring information on page 3. Unit power requirements are located on the serial plate.
2

Installing Cabinetry Over Your Electrical Wiring Information
Jenn-Air Grill Theneutralofthisunitisgroundedtotheframethrough
the green grounding wire. If used on newbranch-circuit
A = 30"(76.2 cm) minimum clearance between the top of installations (1996 NEC), mobile homes, recreational
the cooking platform and the bottom of an vehicles, or in an area where local codesprohibit
unprotected wood or metal cabinet, grounding through the neutral conductor, untwist or
disconnect the green wire and connect the green wire to
A = 24"(60.96 cm) minimum when bottom of wood or
metal cabinet is protected by not less than 1/4"ground in accordance with local code. Connect the white
(0.635 cm). FLAME RETARDANT millboardcovered neutraltotheserviceneutral.Connect all wires to the
with no less than no. 28 MSG sheet steel, 0.015" branch circuitwith approved connectors. Use copper or
(0.038 cm) stainless steel, 0.024"(0.061 cm) aluminum wire. If aluminum wire is used, use connectors
aluminum or copper, recognized for joining aluminum tocopper.
*To eliminate the risk of burns or fire by reaching over
heated surface units, cabinet storagespace located Proper Electrical Supply
above the surface units should be avoided.If cabinet You must provide an adequate electrical supply system
storage is to be provided, the risk can be reduced by as required for your cooktop. All wire connections must be
installing a range hood that projects horizontally a in accordance with local codes and properly insulated.
minimum of 5 inches beyond the bottom ofthe cabinets.Checkwith local utility for governing electrical codes and
ordinances. In the absenceof local electrical codes, the
National Electrical Code,NFPA No.70, governing electric
DOTTEDLINES Fcooktop installations must be followed.A copy of the
[NDICATE
RANGEHOOD I_ National Electrical Code, NFPA No. 70,can be obtained
CONSTRUCTION_ by writing to:
t National Fire Protection Association
* A BatterymarchPark
Quincy, Massachusetts 02269
I
A three-wire, single phase, A.C. 1201240 volt 60 cycle
electrical system (properly circuit protectedto meet local
Installer Installation Suggestions Codes of NFPA No. 70)must be provided. Unit must be
1.Chamferallexposededges ofdecorativelaminateto properlygroundedinaccordancewithlocalwiringcode,
preventdamagefromchipping. Thechartbelowrecommendsthe minimumcircuit
protector and wire size if the appliance isthe only unit on
2.Radius corners of cutout and file to insure smooth the circuit.If smaller sizes of wire are used, the unit
edges and prevent corner cracking, efficiency will be reduced and a fire hazard may be
created. It is advisable that the electrical wiring and
3. Roughedges, inside corners which have not been hookup be accomplished by a competent electrician.
rounded and forced fits can contribute to cracking of
the countertop laminate.
4. Countertop must be supportedwithin 3"(7.62 cm) of
cutout. RECOMMENDEDMINIMUM
K,W.RATING CIRCUITPROTECTION WIRESIZE
CAUTION o. SERIALPLATE INAMPERS(AWG)
Warrantyis voidon Jenn-Airequipment 0- 4.9 2012
installedotherthan as recommendedby 5.0- 6.9 30 10
manufacturer.Recommendedwallcapsand 7.O-9.9 408
transitions must be utilized for proper lO,0-11.9 50 8
operationandinstallation. 12.0-14.9 60 6

Preparing Unit For Assembly In Countertop
1. Unpack Unit.
2. Providecutoutforcountertopandductopeningsas
required per page 1.
3.Place unit in the cutout, and slide unit all the way to the
left hand side of cutout. (Figure 1).
4. HOLDING DOWN UNIT TO COUNTERTOP: Use the
hold down straps, provided in the hardware package, to _."",,_.,.,,,,_-,_:!."-",
secure unit tothe countertop.These straps may be ,-------._ _
positioned on the left, front, and back sides of the unit.
(See figure 1A).To install, pre-thread the bolt into the
strap about 2 inches. With the unit positioned in the
cutout as desired,reach through the cabinet door
opening and push up along the wall of the burner box
flange.If it doesn't hook, pull strap down, move it left or FIGURE 1A FIGURE 1
right about an inch and push up again. Once strap is
hooked, thread bolt intostrap until it meets resistance
against bottom of countertop. Then tighten slowly until
unit top bottomsagainst countertop. __._
5. Connect outlet of blower housing to vent duct. Loosen
cap nuts inside plenum to rotate blower housing to CO.'mOLgOX _
desired position. __
6.Remove attachment screw and cover from junction
box. Connect BX Cable power supply to knockout in ,_J-"---//, _ Q'_ _ exc,eu_
side of box. Make wire connections, push wires into
box. Re-attach cover. Consult focal codes for proper
power hookup. (Figure 2). ,u,c'r,o,,,ox|_'_" _ _k
7. Test to insure electronic surface control operates all
elements properly. FIGURE 2

2nOEowardsStreet,SE
Ceve!_nd.Tennessee37311
Tei:423-472-3333
Fax:-t23-478-67]0
I0. FLOOR VENT CUTOUT (JOISTS AS SHOWN)
-Check the directionof the floor joists (see illustration). If thejoists" .directionis as shown, locate
the cutout on the "T" as illustrated.The cutout must miss the floorjoists!
-Cutout may be moved from side to side on line to clearfloor _ist.
- Recheck your dimensions and make the cutout.
11. FLOORVENT CUTOUT (JOISTS AS SHOWN)
- Check the direction of the floor joists (see illustration). Ifthe joists' direction is as shown,locate
the cutouton the "T"as illustrated. The cutout must miss the floor jolstsl
- Cutoutmaybe moved from frontto back on line to clearfloor joist.
- Recheck yourdimensions and make the cutout.
ONTHISUNE [
k I ,
---_ !
12. WALL VENT CUTOUT
- Locate the vertical studs in the rear wall. Studsare us_liy 16" (40.64 cm)center to center.
- Will the vent duct be 6"(15.24 cm) round through the wall or 3 1/4" x10" (8.26 cmx 25,4 cm)
rectangle,vertically iuside the wall?
- See Ducting Instructions for rear duct inside the wall. NOTE: Cutout inwall must clear 3 1/4" x
10"(8.26 cm x 25.4 cm) transition elbow.
- Locate the closest stud to your proposed vent hole location. Use the following chart to figure the
"X" dimension. See the illustration tbrthe other dimeusions.
:[VERTICAL DUCT INSIDE WALL
1
6" Round('f5.24 ¢m) 3%"x10"
(8.26 em x 25.4 cm)
I "X"MINIMUM 4"(10.16era) 6"(15.24cm)
- A 1" (2.54 cm) length of duct must protrude through the wall for connection to the Blower.
111.59eml
\
_'_.MAYL_GAdmiral?| ....... JENN-,_ * MLagi¢_._.et

2&OEawards$tree!, SE
C;a'leiand,Tennessee37311
TeJ:J-23-,:77_-_333
Fax:_23--;78-_7!0
13. INSTALL BLOWER (PRIORTO INSTALLING RANGE)
- Refer to your vent plan. Itmay be desirable to attach part of the ducting to the blowerbefore it
is installed.
- Position the blower (see illustration) and attach it to the floor withat least two (2) screws.
-Apply duct tape around blower exhaust/duct joint. THROUGH THROUGH
OUT$1OEWALL THEFLOOR
14,INSTALL ELECTRICAL oucrTAPE
- NOTE: Observe all local electrical codes.
- CAUTION: Make sure power to cable is OFF:
- Locate the electric power supply in the floor or wall, any place in the shaded areas which will
clear the blower.
- Direct Connect. Pull through 5' (152.4 era) of electrical cable.
- Use three or four conductor copper stranded power cable (see front cover for proper wire size). If
four conductor wire is used, see #16 for connection to range.
-See frontcover for proper supply connection, j 1
4'ho(11.43_ -- J
t
5 FE_=TOF
ELECTRICAL CABLE
15. COI_E:CT ELECTRICAL (THREE CONDUCTORW1KE)
- CAUTION: Make sure power to cable is OFF.
- Remove the range electrical service cover,located on the back,lower lefthand corner.
- l_tall a 3/4"(1.91 cm) clamp in the hole provided below the terminal block.
- Strip 3" (7.62 cm) of outer insulation from the cable.
- Strip I/2" (1.27 era) of insulation from each wire.
- Pull the cable through the cable clamp. Attach the BLACK, RED, and WHITE wires (see
illustration). Tighten the terminal block nuts and the cable clamp and i_tall cover.
_C,_,BLECLAMP

2_0EdwardsStreet,SE
Cieve!and,Ten_esse_37311
Tei:_13-472-3_3
Fax:a23-47S-87tO
16. CONNECT ELECTRICAL (FOUR CONDUCTOR WIRE)
- CAUTION: Make surepowerto cable is OFF.
-Remove the range electrical service coverlocated on the back, lowerleft-band corner. Remove the
ground strapscrew and bend thestrap up as shown.
- install a 3/4"(1.19 cm)cableclamp in theholeprovided,below the terminalblock.
-Strip3"(7.62cm)of outer insulation from the cable.
-Strip 1/2" (1.27 cm) of insulationfrom each wire.
- Pull thecable through thecableclamp.
- Makea loop in the bareground wireand attach it to therangewith thesCrewthat held theground
strap.
- Attach theBLACK, RED,and WHITE wires(see #15). Tightenthe terminal block nuts andthe
cable clamp.
-Tapethe ground stra to the WHITE wire as shown. InstaLlelectrical cover.
upII I I
17.INSTALL OPTIONS
- If a backsplashor side panels are tobe used, install according to instructions includedwith those
accessories.
,/i I i :
: /
0-I I il
18. POSITION RANGE
- Free-Standing: Adjust therange feet sothe range and cabinet height will be approximately the
same. Slide the range into place, taking care not to daraage floor covering.
- Slide-In: Carefully lit_ and place the range on the cabinet top.

Z_OE_watdsStreet.SE
C',eveiend.Tennessee37311
Te!:422-_72-3333
7-ax:_23-_78-67:0
19.ANTI-TIP BRACKET INSTALLATION
-With the unit installed inthe final location, establish left side and backof the unit.
-Locate left bracket 5/8"(1.58cm) in from the left of the unit.
- Locate the right bracket 27 7/8"(70,80 cm) to the right of the left bracket.
- Locate the rear of both brackets flush to the back of the unitifa backsplash is not used.
* If a lighted backsplashis used, move back of brackets forward 1/8"(.318 era), If a non-lighted
backsplashis used, moveback of brackets forward 1/4"(.635 eta).
- NOTE: Leg levelers mustbe screwed out I 1/2 turns. If the flOorwill not accept the wood
screwssupplied, alternate fastenerstaust be supplied by theinstaller.
_TERNA_SCREWHOLEtFw_0
t_ 27',t"(70.80erni
%"(1.58cm)
20. LEVEL RANGE
- Free-Standing: Adjustthe leveler feet to levelrange with the countertop.
-Slide-In:Adjust the leveler feet totakesome of the weightoffofthe ccuntertop.
-Unit mustbe level for optimumbakingperformance.
i--- r-'[_o I _, I_ ! o©
B
21. CONNECT BLOWER ELECTRICAL
- Connect the blower power cord to the power cord onthe range.(See illustration).
BLOWER !!
POWERCORD
(
1

2.40EdwardsStree[.SE
C;eveiana,Tennessee373]l
Tei:422-477_-,2333
Fax:_t22-._7_-6770
22. INSTALL FLEXDUCT
- Attach theflex ducttothe blower and range (See illustration). Using a screwdriver, securely tighten
duct clamp at each connection.
23. CHECK OPERATION
- Unpack and in.stallgrill elementin one sideand cooking cartridge in other side.
- 8e sureto remove all packagingmaterials fromunit prior to applying power.
- Switch the electrical circuit breaker tothe ON position.
- Consult Owner's Manual for operation.
- Check range top elements. Fancomesonautomatically whengrill is turned on, cooking
cartridge does not energize fan automatically.
- Check oven.
-Check vent fan.
- Withvent fan on, check all vent duct connections to the outside to make sure there are no airleaks.
24.INSTAL[,LOWER DOOR
-After'check for air leaks at duct connections, install thelower rangedoor.