Jenn-Air RADIANT COOKTOP CVE3401 User manual

RadiantDowndraftCooktop]JENN-AIR
ModelCVE3401 J_WEST_00RTHSTRE_,O_,H.,_ON,_
INSTALLATION
INSTALLER -SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.
Installation should be performed only by an authorized Jenn-AirService Contractor orother qualified installer.
Read Safety Precautionsin the Use & Care Manual before using this appliance.
INSTRUCTIONSTO INSTALLER: SideClearance-Unitmay be safelyinstalledas nearas 0"(0 cm) froma sidewall
if spacelimitationsrequires.However,asideclearanceof atleast6" (15.24cm) is recommendedforoptimumventilation.
NOTICE TO INSTALLER: Leave these instructionswith the appliance.
NOTICE TO CONSUMER: Retain these instructionsfor future reference.
29 3/4"_
[75.27cm] _..._\
_ \ "22.
'_ 28 7/8"_1/16"_21 1/8" ±1/8"
[73.05cn_,16 cm [53,66cm±.52 cm]
tO"CUTOUT
I_I SELECTAPPROPRIATE
I_ _ DUCTCUTOUT.
L•// BLOWERMAY BE ROTATED
_./"_/FORt"K_IZONTAL OR
_"_,n// VERTICAL DIRECTION BY
_ _ _ /_/ LOOSENINGNUTS AROUND
"_'_ _ ..,,f/'J¢ fTHE BLOWERINLET,
(SEE OUCTING INSTRUCTIORS.)
_"_ 2g 3/4 ° ,.I
l[75,27 cm] ,
J11,75cm _J
,, ,/2 (_ II_,
_""°=J I U I1"-,._, .
I I ._1 II-,--12_/2" •
MINIMUM CABINET lI..,_
TO MOTORCLEARANCE --'_ ]21.'2-
FOR COOLINGPURPOSE. _-[31.76 cm|
8101P419-60
(10-01-00)

Installing Cabinetry Over Your ElectricalWiring Information
Cooktop The neutral of thisunit is grounded to the frame through
A = 30" (76.2 cm) minimum clearance between the top of the green grounding wire. If used on new branch-circuit
the cooktop and the bottom of an unprotected wood installations (1996 NEC), mobile homes, recreational
or metal cabinet, vehicles,or in an area where local codes prohibit
grounding through the neutral conductor, untwist or
A = 24"(60.96 cm) minimum when bottom of wood or disconnect the greenwire and connect thegreenwireto
metal cabinet is protected by not less than 1/4" ground in accordance with localcode, Connect the white
(0.635cm). FLAME RETARDANT millboard covered neutral to theservice neutral, Connect all wires to the
with not less than no. 28 MSG sheet steel, 0.015" branch circuit with approvedconnectors.Use copper or
(0.038 cm) stainless steel, 0.024"(0.061 cm) aluminumwire,If aluminum wire is used, use connectors
aluminum or copper,recognized for joining aluminum to copper.
* To eliminate the risk of burns or fire by reaching over
heated surface units, cabinetstorage space located Proper ElectricalSupply
above the surface units should be avoided,If cabinet
storage is to be provided, the risk can be reduced by You must provide an adequate electrical supplysystem
installing arange hood that projects horizontally a as required for your cooktop.All wireconnectionsmust be
minimum of 5 inches beyond the bottom of the cabinets, in accordance with local codes and properly insulated.
Check with local utilityfor governing electrical codesand
ordinances. In the absence of local electrical codes, the
iF'-"-' National ElectricalCode, NFPA No. 70, governing electric
DOTTEDLINES range installations must be followed. A copy of the
INDICATE
RANGEHOOD U National Electrical Code, NFPA No. 70, can be obtained
CONSTRUCTION..,._%_ by writingto:
"../_ National Fire Protection Association
Batterymarch Park
J:_*Quincy, Massachusetts02269
k _A._.._._.__ A three-wire, singlephase, A,C. 120/240volt 60 cycle
L_..-.-..,-... electrical system (properly circuit protected to meet Local
Codes of NFPA No. 70) must be provided. Unit must be
Installer Installation Suggestions properly grounded inaccordance with localwiring code.
The chart belowrecommendsthe minimum circuit
1.Chamfer allexposed edges of decorative laminate to protector and wire size if the appliance isthe only unit on
prevent damage from chipping, the circuit. If smaller sizes of wireare used,the unit
efficiency will be reduced and a fire hazard may be
2.Radiuscorners of cutout and file to insure smooth created. It isadvisable that the electrical wiring and
edges and prevent corner cracking, hookup be accomplished bya competent electrician.
3. Rough edges, inside corners which have not been
rounded and forced fitscan contribute tocracking of RECOMMENDEDMINIMUM
thecountertop laminate. K.W.RATING CIRCUITPROTECTION WIRESIZE
ONSERIALPLATE INAMPERS (AWG)
4. Countertopmustbesupportedwithin3"(7,62 cm) of
cutout.0- 4,9 2012
5.0- 6,9 3010
7.0- 9,9 408
10.0-11.9508
12.0-14,9 60 6

NoticeTo Installer InstallationOf Appliance
Followaccompanying instructions carefully.1.Unpack unit.
2. Provide cutout for countertop and duct opening as
This appliance isdesigned to always be vented outdoors. required per page 1.
This appliance should be ducted separately from other 3. Place unit in the cutout.
vented appliances. 4. Loosen cap nutsinsideplenumto rotateblower
housing to desired position. Connect outlet blower
CAUTION housing tovent duct. Tighten capnuts inside plenum.
Neveruse ametal bladeto pryknob off. Ifknob 5. Remove attachment screw and cover from junction
cannot be easily removed, tuck foldsof a box.ConnectBXcabletoknockoutonsideofthe
junction box. Make wire connections, pushwires into
dishtowelunderknobskirtand pullupwardwith junctfonbox.Re-attachcover.Consuttlocalcodesfor
steady, even pressure, proper power hookup (figure 1).
6. Test to insure control knobs operateall elements
properly.
NBOX
BXCABLE-_'_'_,_f_ RIGHTCENTER
FIGURE 1

240Edwards$[reer. SE
Cleveland,Tennessee373;;
Te}:_23-472-3333
Fax:[phone]
7.SLIDE-INCUTOUT
-Check yourmarked-updimensionscarefully.The reardimensionsshownintheillustrationmust
bemaintained.
-NOTE: Where thisisnotdone,itwillbe necessarytorelieveaportionoftheundersideoftbe
countenopand/orsupportmembers tocleartherangerearpanel.
-Cutting toleranceis 4- 1/16"(.16 cm). ._.., _=" _,_
-Carefully mark the cutout.___,,._Top ""-. ,,_-tltu.--
aT_)
I%" I
8.OVER-RANGE CABINETS %
- To eliminate the hazard of reaching overa heated surface unit, cabinet storage space above the
range should be avoided.However, if over-rangecabinets are necessary, observe the following:
B=30" (76.2 cm) minimum clearance between thetop oftbe cooking platform and the
bottom of an unprotected wood ormetal cabinet.
B=24" (60.96 era) minimum when bottom of wood ormetal cabinetis protected bynot
less than 1/4" (0.635 era) FLAME RETARDANT millboardcovered with not less than
No. 28 MSG sheet steel, 0.015"(0.038 era)stainless st_l, 0.024" (0.061 cm) aluminum
or copper.
-If unit will be vented through the wall, go to #12.
- Using a square and marking pen, draw the "T" cutout line on the floor (see illustration). Recheck
your dimensions.
- If floor will be concrete slab, see enclosed ducting instructions.
-For left and right hand venting through cabinet toe space, see enclosed ducting instructions.
•10%_
j S"
'7- L_...J .,-Y
/(le.sa,=mj- i_..wt='_)
[],MAY1-AG Admlr,al 7J _ JENN-,.MI:I ._ ._ditcJl¢ C.,_e.f

2nOEowardsStreet,SE
Ceve!_nd.Tennessee37311
Tei:423-472-3333
Fax:-t23-478-67]0
I0. FLOOR VENT CUTOUT (JOISTS AS SHOWN)
-Check the directionof the floor joists (see illustration). If thejoists" .directionis as shown, locate
the cutout on the "T" as illustrated.The cutout must miss the floorjoists!
-Cutout may be moved from side to side on line to clearfloor _ist.
- Recheck your dimensions and make the cutout.
11. FLOORVENT CUTOUT (JOISTS AS SHOWN)
- Check the direction of the floor joists (see illustration). Ifthe joists' direction is as shown,locate
the cutouton the "T"as illustrated. The cutout must miss the floor jolstsl
- Cutoutmaybe moved from frontto back on line to clearfloor joist.
- Recheck yourdimensions and make the cutout.
ONTHISUNE [
k I ,
---_ !
12. WALL VENT CUTOUT
- Locate the vertical studs in the rear wall. Studsare us_liy 16" (40.64 cm)center to center.
- Will the vent duct be 6"(15.24 cm) round through the wall or 3 1/4" x10" (8.26 cmx 25,4 cm)
rectangle,vertically iuside the wall?
- See Ducting Instructions for rear duct inside the wall. NOTE: Cutout inwall must clear 3 1/4" x
10"(8.26 cm x 25.4 cm) transition elbow.
- Locate the closest stud to your proposed vent hole location. Use the following chart to figure the
"X" dimension. See the illustration tbrthe other dimeusions.
:[VERTICAL DUCT INSIDE WALL
1
6" Round('f5.24 ¢m) 3%"x10"
(8.26 em x 25.4 cm)
I "X"MINIMUM 4"(10.16era) 6"(15.24cm)
- A 1" (2.54 cm) length of duct must protrude through the wall for connection to the Blower.
111.59eml
\
_'_.MAYL_GAdmiral?| ....... JENN-,_ * MLagi¢_._.et

2&OEawards$tree!, SE
C;a'leiand,Tennessee37311
TeJ:J-23-,:77_-_333
Fax:_23--;78-_7!0
13. INSTALL BLOWER (PRIORTO INSTALLING RANGE)
- Refer to your vent plan. Itmay be desirable to attach part of the ducting to the blowerbefore it
is installed.
- Position the blower (see illustration) and attach it to the floor withat least two (2) screws.
-Apply duct tape around blower exhaust/duct joint. THROUGH THROUGH
OUT$1OEWALL THEFLOOR
14,INSTALL ELECTRICAL oucrTAPE
- NOTE: Observe all local electrical codes.
- CAUTION: Make sure power to cable is OFF:
- Locate the electric power supply in the floor or wall, any place in the shaded areas which will
clear the blower.
- Direct Connect. Pull through 5' (152.4 era) of electrical cable.
- Use three or four conductor copper stranded power cable (see front cover for proper wire size). If
four conductor wire is used, see #16 for connection to range.
-See frontcover for proper supply connection, j 1
4'ho(11.43_ -- J
t
5 FE_=TOF
ELECTRICAL CABLE
15. COI_E:CT ELECTRICAL (THREE CONDUCTORW1KE)
- CAUTION: Make sure power to cable is OFF.
- Remove the range electrical service cover,located on the back,lower lefthand corner.
- l_tall a 3/4"(1.91 cm) clamp in the hole provided below the terminal block.
- Strip 3" (7.62 cm) of outer insulation from the cable.
- Strip I/2" (1.27 era) of insulation from each wire.
- Pull the cable through the cable clamp. Attach the BLACK, RED, and WHITE wires (see
illustration). Tighten the terminal block nuts and the cable clamp and i_tall cover.
_C,_,BLECLAMP

2_0EdwardsStreet,SE
Cieve!and,Ten_esse_37311
Tei:_13-472-3_3
Fax:a23-47S-87tO
16. CONNECT ELECTRICAL (FOUR CONDUCTOR WIRE)
- CAUTION: Make surepowerto cable is OFF.
-Remove the range electrical service coverlocated on the back, lowerleft-band corner. Remove the
ground strapscrew and bend thestrap up as shown.
- install a 3/4"(1.19 cm)cableclamp in theholeprovided,below the terminalblock.
-Strip3"(7.62cm)of outer insulation from the cable.
-Strip 1/2" (1.27 cm) of insulationfrom each wire.
- Pull thecable through thecableclamp.
- Makea loop in the bareground wireand attach it to therangewith thesCrewthat held theground
strap.
- Attach theBLACK, RED,and WHITE wires(see #15). Tightenthe terminal block nuts andthe
cable clamp.
-Tapethe ground stra to the WHITE wire as shown. InstaLlelectrical cover.
upII I I
17.INSTALL OPTIONS
- If a backsplashor side panels are tobe used, install according to instructions includedwith those
accessories.
,/i I i :
: /
0-I I il
18. POSITION RANGE
- Free-Standing: Adjust therange feet sothe range and cabinet height will be approximately the
same. Slide the range into place, taking care not to daraage floor covering.
- Slide-In: Carefully lit_ and place the range on the cabinet top.

Z_OE_watdsStreet.SE
C',eveiend.Tennessee37311
Te!:422-_72-3333
7-ax:_23-_78-67:0
19.ANTI-TIP BRACKET INSTALLATION
-With the unit installed inthe final location, establish left side and backof the unit.
-Locate left bracket 5/8"(1.58cm) in from the left of the unit.
- Locate the right bracket 27 7/8"(70,80 cm) to the right of the left bracket.
- Locate the rear of both brackets flush to the back of the unitifa backsplash is not used.
* If a lighted backsplashis used, move back of brackets forward 1/8"(.318 era), If a non-lighted
backsplashis used, moveback of brackets forward 1/4"(.635 eta).
- NOTE: Leg levelers mustbe screwed out I 1/2 turns. If the flOorwill not accept the wood
screwssupplied, alternate fastenerstaust be supplied by theinstaller.
_TERNA_SCREWHOLEtFw_0
t_ 27',t"(70.80erni
%"(1.58cm)
20. LEVEL RANGE
- Free-Standing: Adjustthe leveler feet to levelrange with the countertop.
-Slide-In:Adjust the leveler feet totakesome of the weightoffofthe ccuntertop.
-Unit mustbe level for optimumbakingperformance.
i--- r-'[_o I _, I_ ! o©
B
21. CONNECT BLOWER ELECTRICAL
- Connect the blower power cord to the power cord onthe range.(See illustration).
BLOWER !!
POWERCORD
(
1

2.40EdwardsStree[.SE
C;eveiana,Tennessee373]l
Tei:422-477_-,2333
Fax:_t22-._7_-6770
22. INSTALL FLEXDUCT
- Attach theflex ducttothe blower and range (See illustration). Using a screwdriver, securely tighten
duct clamp at each connection.
23. CHECK OPERATION
- Unpack and in.stallgrill elementin one sideand cooking cartridge in other side.
- 8e sureto remove all packagingmaterials fromunit prior to applying power.
- Switch the electrical circuit breaker tothe ON position.
- Consult Owner's Manual for operation.
- Check range top elements. Fancomesonautomatically whengrill is turned on, cooking
cartridge does not energize fan automatically.
- Check oven.
-Check vent fan.
- Withvent fan on, check all vent duct connections to the outside to make sure there are no airleaks.
24.INSTAL[,LOWER DOOR
-After'check for air leaks at duct connections, install thelower rangedoor.