Jensen JWM10A User manual

Mode Menu
Power
App Info
App download and operation:
jControl app controls all of
the primary fu nctions of the
JWM10A directly from your
phone or tablet. It can be
found by searching for
After downloading and installing app, pair
your device to the JWM10A as instructed
in “Bluetooth Operation” section in this
guide. Once your device is paired, open
the app and use as instructed. (Device
must be paired to JWM10A before
opening and using app).
Tablet Interface
JWM10A
QUICK REFERENCE GUIDE
Basic Operation
AM/FM Tuner Controls App Control
AS/PS: Press to SCAN through
currently stored presets. Press &
hole to STORE strongest broad-
cast stations in your area.
BAND: Press to select between two AM
BANDS (AM1, AM2) & three FM
BANDS(FM1,FM2,FM3).
STATION STORE PRESETS:
Press & hole to store current
station. Press once to recall stored
channel.
NOTE: Up to 18 FM & 12 AM
channels can be stored.
VOLUME: Press the VOLUME UP
(M)button to increase volume
or Press the VOLUME DOWN
(H) button to decrease volume.
MODE: Press repeatedly until you
reach TUNER mode displayed as
a frequency.
TUNE/SEEK/TRACK: Press >>
button to tune frequency higher.
Press << button to tune frequency
lower. Press and hold to scan to
next strongest station.
|
|
POWER/MODE: Push to turn on.
Press to cycle through sources.
Press & hold to turn OFF and
enter standby mode.
AUDIO/SETTINGS: Press to
bring up AUDIO ADJUSTMENT
options: BASS, TREBLE, &
BALANCE (left to right).
Press & hold to bring up SETTING
MENU options: BLUETOOTH
(ON/OFF), BEEP, ADJUST LCD
BRIGHTNESS, PRESET
VOLUME and RESET. Press
VOLUME UP/DOWN buttons will
adjust each SETTING option
except 'RESET'.
AUX IN: Insert 3.5mm cable from
your portable media device.
RESET: Use a ball point pen or
thin metal object to press the
reser buttons.
BACK: Press to exit any menu.
ZONES OUTPUT: Press any zone button
(ZONE A and ZONE B) to control
corresponding speaker output from the
radio, SPK A, SPK B will appear on the
display.
VOLUME: Press the VOLUME UP (M)
button to increase volume or Press the
VOLUME DOWN (H) button to
decrease volume.
MUTE: Press to MUTE volume.
Press again to resume volume.
“JENSEN jControl”.
Back For ward Volume Control
Play/Pause/Mute
Zone Volume
and Settings

Bluetooth Operation
For owner’s manual, please visit http://www.asaelectronics.com/manuals-guides.
QRG-JWM10A-0717R1
©Copyright 2017 ASA,LLC
MODE: Press repeatedly until
you reach BLUETOOTH mode.
TUNE/SEEK/TRACK: Advance or
reverse tracks on your device.
SETTINGS: Press & hold to
navigate through menu options,
until BT menu options is reached.
Press ENTER to select DEVICE
LIST or PAIR.
ANSWERING PHONE: BT audio
will automatically pause when a
call is answered. It will then
resume once call has ended. In
some cases, it may be necessary
to press the play button to resume
the BT audio.
ALARM ON/OFF: Press & hold
AUDIO/SETTING button to
navigate through menu options,
until Alarm ON/OFF menu option
is reached. Press VOLUME
UP/DOWN to turn ALARM ON or
OFF.
ALARM SET: Press & hold
AUDIO/SETTING button to
navigate through menu options,
until ALARM SET mode is
reached.
In Sleep mode menu, Press the
VOLUME UP/DOWN to set Sleep
timer: 15, 30, 45, 60, 0 minutes.
VIEW/SET: Press to access CLOCK VIEW mode.
Press & hold to set CLOCK time.
TIME SET: Press VOLUME DOWN ▼ (H)
to adjust Hours and VOLUME UP ▲ (M) to
adjust minutes when setting either
CLOCK or ALARM time.
PAIR DEVICE VIA BLUETOOTH: (Make sure the device you intend to pair
with is on and Bluetooth is enabled.) While in Bluetooth mode, press & hold
PAIR to start the process. The JWM10A will then display 'PAIR' and be
able to be paired with for 120 seconds. With your device in Bluetooth
settings, 'JWM10A' should appear as an available device. Tap 'JWM10A' to
connect. Enter the pairing (0000), if requested.
Clock with Alarm