Jensen SMPS-750 User manual

BLUETOOTH ALL-IN-ONE HI-FI MUSIC SYSTEM
WITH PA
MODEL : SMPS-750
USER MANUAL
PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS
UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

E-
1
WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN
BE FULLY INSERTED TO PREVENT BLADE EXPOSURE TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE
The Caution Marking is located at the back enclosure of the a aratus.
The Rating late is located at the back enclosure of the a aratus
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Kee these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this a aratus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation o enings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
a aratus (including am lifiers) that roduct heat.
9. AC ada ter is used as disconnect device and it should remain readily o erable during
intended use. In order to disconnect the a aratus from the mains com letely, the AC
ada ter should be disconnected form the mains socket outlet com letely.
10. Only use attachments/accessories s ecified by the manufacturer.
11. Use only with a cart, stand, tri od, bracket, or table recommended by
the manufacturer, or sold with the roduct. When a cart is used, use
caution when moving the cart/a aratus combination to avoid injury from
ti -over.
12. Un lug this a aratus during lightning storms or when unused for a long
eriods of time.
13. Refer all servicing to qualified service ersonnel. Servicing is required when the a aratus
has been damaged in any way, such as ower-su ly cord or lug is damaged, liquid has
been s illed or objects have fallen into the a aratus, the a aratus has been ex osed
to rain or moisture, does not o erate normally, or has been dro ed.
14. This a liance shall not be ex osed to dri ing or s lashing water and that no object filled
with liquids such as vases shall be laced on the a aratus.
15. Do not overload wall outlet. Use only ower source as indicated.

E-
2
16. Use re lacement art as s ecified by the manufacturer.
17. U on com letion of any service or re airs to this roduct, ask the service technician to
erform safety checks.
18. Power Sources - This roduct should be o erated only from the ty e of ower source
indicated on the marking label. If you are not sure of the ty e of ower su ly to your
home, consult your roduct dealer or local ower com any. For roducts intended to
o erate from battery ower, or other sources, refer to the o erating instruction.
19. Object and Liquid Entry - Never ush objects of any kind into this roduct through
o enings as they may touch dangerous voltage oints or short-out arts that could result
in a fire or electric shock. Never s ill liquid of any kind on the roduct.
20. Damage Requiring Service - Un lug this roduct from the wall outlet and refer servicing
to qualified service ersonnel under the following conditions:
a) When the ower-su ly cord or lug is damaged,
b) If liquid has been s illed, or objects have fallen into the roduct,
c) If the roduct has been ex osed to rain or water,
d) If the roduct does not o erate normally by following the o erating instructions.
Adjust only those controls that are covered by the o erating instructions as an
im ro er adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the roduct to its normal o eration.
If the roduct has been dro ed or damaged in any way, and
e) When the roduct exhibits a distinct change in erformance - this indicates a need
for service.
21. Battery shall not be ex osed to excessive heat such as sunshine, fire or the like.
22. Excessive sound ressure from ear hones and head hone can cause hearing loss
23. Minimum distances of 10 cm around the a aratus for sufficient ventilation.
24. The ventilation should not be im eded by covering the ventilation o enings with items,
such as news a ers, table-cloths, curtains, etc.
25. No naked flame sources, such as lighted candles, should be laced on the a aratus.
26. The use of a aratus in moderate climates.
27. Attention should be drawn to the environmental as ects of battery dis osal.
SAVE THESE INSTRUCTIONS

E-
3
COMPLIANCE WITH FCC REGULATIONS
FCC ID : RSBSMPS-750
This device com lies with Part 15 of the FCC Rules. O eration is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must acce t any interference received, including interference that may
cause undesired o eration.
Note: This equi ment has been tested and found to com ly with the limits for a Class B
digital device, ursuant to Part 15 of the FCC Rules. These limits are designed to rovide
reasonable rotection against harmful interference in a residential installation. This
equi ment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
articular installation. If this equi ment does cause harmful interference to radio or television
rece tion, which can be determined by turning the equi ment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the se aration between the equi ment and receiver.
- Connect the equi ment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an ex erienced radio/TV technician for hel .
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment
PRECAUTIONS BEFORE USE
•DO NOT CONNECT THE AC ADAPTER TO THE MAINS BEFORE CHECKING THE
MAINS VOLTAGE AND UNTIL ALL OTHER CONNECTIONS HAVE BEEN MADE.
•DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF
SEVERAL INCHES AROUND THE UNIT FOR VENTILATION.
IMPORTANT NOTES
•Sto o eration immediately if any liquid or solid object should fall into the cabinet.
•If the unit is not to be used for a long eriod of time, make sure that all ower sources
are disconnected from the unit. Remove the battery from the remote control battery
com artment, and un lug the AC ada ter from the wall outlet. Make it a ractice to
remove the AC ada ter by gras ing the lug and not by ulling the cord.
•Places ex osed to direct sunlight or close to heat radiating a liances such as electric
heaters.
•Places subject to constant vibration.
•Dusty, humid or moist laces.
•Un lug the unit’s AC ada ter from the electrical ower outlet immediately in case of
malfunction.

E-
4
PROTECT YOUR FURNITURE
This model is equi ed with non-skid rubber 'feet' to revent the roduct from moving when
you o erate the controls. These 'feet' are made from non-migrating rubber material s ecially
formulated to avoid leaving any marks or stains on your furniture. However certain ty es of
oil based furniture olishes, wood reservatives, or cleaning s rays may cause the 'feet' to
soften, and leave marks or a rubber residue on the furniture. To revent any damage to your
furniture we strongly recommend that you urchase small self-adhesive felt ads, available
at hardware stores and home im rovement centers everywhere, and a ly these ads to
the bottom of the rubber 'feet' before you lace the roduct on fine wooden furniture.
DEAR JENSEN CUSTOMER
Selecting fine audio equi ment such as the unit you've just urchased is only the start of
your musical enjoyment. Now it's time to consider how you can maximize the fun and
excitement your equi ment offers. This manufacturer and the Electronic Industries
Association's Consumer Electronics Grou want you to get the most out of your equi ment
by laying it at a safe level. One that lets the sound come through loud and clear without
annoying blaring or distortion and, most im ortantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing "comfort level" ada ts to higher volumes
of sound. So what sounds "normal" can actually be loud and harmful to your hearing. Guard
against this by setting your equi ment at a safe level BEFORE your hearing ada ts.
To establish a safe level:
•Start your volume control at a low setting.
•Slowly increase the sound until you can hear it comfortably and clearly, and without
distortion.
•Once you have established a comfortable sound level : Set the dial and leave it there.
Taking a minute to do this now will hel to revent hearing damage or loss in the future.
After all, we want you listening for a lifetime.
We Want You Listening For a Lifetime
Used wisely, your new sound equi ment will rovide a lifetime of
fun and enjoyment. Since hearing damage from loud noise is
often undetectable until it is too late, this manufacturer and the
Electronic Industries Association's Consumer Electronics Grou
recommend you avoid rolonged ex osure to excessive noise.
Customer's Record:
The serial number of this roduct is found on its back cover. You should note the serial
number of this unit in the s ace rovided as a ermanent record of your urchase to aid in
identification in the event of theft or loss.
Model Number: SMPS-750 Serial Number: ____________________

E-
5
LOCATION OF CONTROLS
MAIN UNIT
1. AUX IN 12. MODE/STANDBY
2. LED ON/OFF SWITCH 13. / CH-
3. ECHO CONTROL 14. / SCAN
4. USB PORT 15. / CH+
5. SD CARD SLOT 16. LED DISPLAY
6. EQ ADJUSTMENT CONTROL 17. REPEAT
7. MIC IN 18. MASTER VOLUME
8. GUITAR IN 19. POWER SWITCH
9. TREBLE CONTROL 20. DC IN JACK
10. BASS CONTROL 21. AUX OUT
11. MIC/GUITAR VOLUME

E-
6
REMOTE CONTROL
The remote control o erates on one CR2025 battery (included).
To activate the remote control, remove the insulation tab inserted in the battery com artment.
When the o eration of the remote control becomes intermittent or unsatisfactory, re lace
the original battery with a new 3V lithium battery.
1. Press down on the com artment cover, slide out the battery holder from the remote
control case.
2. Re lace the 3V CR2025 battery. Be sure the battery is installed correctly. The
remote will not work if the battery is installed with the wrong olarity.
CAUTION:
1. Danger of ex losion if the battery is re laced incorrectly.
2. Re lace only with the same or equivalent ty e battery.
Note: Only use a well-known brand of battery to ensure the longest life and best
erformance.
WARNING
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
The remote control su lied with this roduct contains a coin/button cell battery. If the
coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and
can lead to death.
Kee new and used batteries away from children. If the battery com artment does not
close securely, sto using the roduct and kee it away from children.
If you think batteries might have been swallowed or laced inside any art of the body, seek
immediate medical attention.

E-
7
CONTROLLING THE VOLUME
This unit features a MASTER VOLUME CONTROL (#18) located on the main unit. The
out ut volume level is initially controlled based on where this control is set.
It’s im ortant that if you use the remote control to adjust the volume, make sure the MASTER
VOLUME CONTROL (#18) is always set to maximum rior to using the remote control.
Note: If the MASTER VOLUME CONTROL (#18) is set below the maximum volume level,
the out ut volume level will be reduced if you use the remote control. Exam le: if the
MASTER VOLUME CONTROL (#18) is set to 50%, you will only be able to adjust between
0 and 50% of the full volume when using the remote control.
When using the remote control to adjust the volume level, you will notice that the LED dis lay
shows V00-V30 as you adjust the volume level. V00 meaning the lowest volume level, and
V30 is maximum. Make sure the volume level on the remote control is always left at V30 if
you decide to switch to using the MASTER VOLUME CONTROL (#18) instead of the remote
control. Leaving the remote control volume level set below V30 will reduce the audio out ut
on the SMPS-750. Turning the POWER SWITCH (#19) OFF and then ON again will reset
the volume control setting in the main unit, and restore full use of the MASTER VOLUME
CONTROL (#18).
LED DISPLAY
The LED dis lay will show the following codes when that feature is active.
bt = dis lays when you are in BLUETOOTH mode
LInE = dis lays when you are in AUX mode
OnE = dis lays when “Re eat One” is selected during layback
ALL = dis lays when “Re eat ALL” is selected during layback
nOr = dis lays when “No Re eat” is selected during layback
6 Preset EQ Settings - Only accessible when using the "EQ" button on the remote control
nOr = dis lays when “NORMAL” EQ setting is selected
POP = dis lays when “POP” EQ setting is selected
rOC = dis lays when “ROCK” EQ setting is selected
JAZ = dis lays when “JAZZ” EQ setting is selected
CLA = dis lays when “CLASSIC” EQ setting is selected
Cut = dis lays when “COUNTRY” EQ setting is selected
Note: The reset EQ settings are only available when in Bluetooth or USB/SD modes.
Volume Level – Only shows when using the "VOLUME" buttons on the remote control V00
to V30
Note: The volume level range controlled by the remote control is limited by the MASTER
VOLUME CONTROL (#18). The MASTER VOLUME CONTROL (#18) should be set around
the half way oint on the dial before you first ower u the unit.

E-
8
POWER SOURCE
An AC 120V ~ 60Hz ower ada ter with an out ut voltage of DC15V 3A is included with the
SMPS-750.
POWER CONNECTION
1. Insert the DC lug of the AC ada ter into the DC IN Jack (#20) on the unit.
2. Plug the AC ada ter into an AC wall outlet.
3. Set the POWER Switch (#19) and the LED Switch (#2) to ON.
4. The SMPS-750 will turn ON, and all the LEDs on the to anel and in the s eakers will
light.
Note:
Please remove the AC ada ter from the wall outlet and un lug it from the SMPS-750 if the
unit is not being used for extended eriods of time.
CAUTION :
Only use the AC ada ter included with the SMPS-750. Using a different ada ter could
damage the unit and void the warranty.
RADIO OPERATION
The following ste s can also be com leted using the remote control. Check the remote control
diagram for the corres onding buttons.
1. Press the POWER SWITCH (#19) located on the back of the SMPS-750 to turn ON the
unit. Press and hold the MODE/STANDBY BUTTON (#12) to wake u the system if
necessary.
2. Ta the MODE/STANDBY BUTTON (#12) re eatedly to select FM mode. The frequency
will show on the LED DISPLAY (#16).
3. Press the BUTTON (#15) or BUTTON (#13) re eatedly to manually tune to a
desired station.
4. To automatically search for stations with strong signals, ress and hold the
BUTTON (#15) or BUTTON (#13) until the frequency read out on dis lay begins to
scan then release the button. The tuner will sto on the first strong station signal it finds.
5. Adjust the MASTER VOLUME CONTROL (#18) to the desired sound level.
To set / recall the radio presets
• The unit can automatically search and store the reset memories. Press and hold the
PLAY/PAUSE BUTTON (#14) for 4~5 seconds to activate auto reset mode and the
total number of stations can be stored de ends on the signal strength of broadcasting
stations.
• To recall one of the reset stations already rogrammed, ta the PLAY/PAUSE
BUTTON (#14) re eatedly until you reach the desired reset number/radio station.
Notes:
• Use manual tuning to select weaker stations that might be ski ed or missed during
automatic tuning.
• If the automatic tuning does not sto on the exact frequency of the station, for exam le,
it sto s on 100.9MHz instead of 100.8MHz, use the manual tuning method to "fine tune"
to the exact frequency of the desired station.
• You can also direct enter the frequency by using the remote control.
For exam le, 88.1MHz (enter 881 with remote control), 100.8MHz (enter 1008 with
remote control).

E-
9
TIPS FOR BEST RECEPTION
FM - During FM rece tion, always kee the FM Wire Antenna fully extended and
hanging high u on the wall. If rece tion is weak, try re ositioning the FM Wire Antenna
until you find the strongest signal.
BLUETOOTH OPERATION
Pairing a Bluetooth enabled device with the SMPS-750.
1. Turn on the SMPS-750.
2. Ta the MODE BUTTON (#12) re eatedly to select Bluetooth mode. “bt” will a ear on
the LED DISPLAY (#16) and flash. You will hear four (4) “bee s” confirming you are in
airing mode.
3. Turn on the Bluetooth function of the device you want to link to and enable the search
or scan function to find the SMPS-750.
4. Select "SMPS-750" from the device list when it a ears on your device screen. If
required, enter the ass code “0000” to air (link) SMPS-750 with your device.
5. If you are airing (linking) your com uter to the s eaker using Bluetooth, you may need
to set the SMPS-750 as your com uter’s default sound device.
6. After successfully airing the SMPS-750 with your Bluetooth device. You will hear two
(2) “bee s” confirming that the device is connected.
7. If you want to air (link) the SMPS-750 with another Bluetooth device, disconnect the
connection by using the connected BT device. You will hear a disconnect tone which are
three (3) “bee s”. Re eat ste s 3 & 4. You will hear a confirmation tone to confirm that
the new airing is successful.
Now you can lay music from your Bluetooth device wirelessly to the SMPS-750.
1. Select your favorite song, ress the Play/Pause on your Bluetooth device or the
PLAY/PAUSE BUTTON (#15) on the SMPS-750 to lay or ause the song from your
Bluetooth device.
2. Ta the BUTTON (#12) or BUTTON (#13) to select the Next or Previous track.
3. Slowly adjust both the volume control of your SMPS-750 and your Bluetooth device until
you reach a comfortable listening level.
Notes:
• Refer to the manual of your cell hone, tablet PC, com uter or other Bluetooth
enabled devices for Bluetooth o eration since it may vary from model to model.
• If your Bluetooth enabled device does not su ort A2DP rofile, it will not lay the
music through the s eaker, even if aired (linked).
• Remember to turn off the SMPS-750 when you have finished listening.
• Don't forget to switch off the ower of your Bluetooth device as well.
• The re eat function does not a ly to the Bluetooth o eration.

E-10
USB/SD PLAYER OPERATION
The SMPS-750 is com atible with, and will lay MP3 files that are stored on a USB flash
drive or SD memory card.
1. Press the POWER SWITCH (#19) to turn the unit ON.
2. Plug a USB flash drive into the USB ort (#4) or insert a SD CARD into the SD SLOT
(#5). The unit will automatically switch modes and begin reading the flash drive or SD
card. The total number of tracks will show on the LED DISPLAY (#16).
3. Press the PLAY/PAUSE BUTTON (#14) to ause the USB or SD card layback,
and ress again to resume.
4. During PLAY mode, ta the BUTTON (#15) or BUTTON (#13), the layer will
go to next or revious track.
5. During PLAY mode, ress and hold the BUTTON (#15) or BUTTON (#13), the
layer will lay fast forward or fast backward.
6. Ta the REPEAT BUTTON on the remote control re eatedly during layback to select
re eat ONE, re eat ALL and cancel re eat.
AUX IN OPERATION
You can lay other music sources (iPod, MP3 or other digital audio layers) through the
s eakers of the SMPS-750 by connecting the AUX IN Jack (#1) to your external layer’s
audio out jack or head hone jack.
1. Plug one end of an audio cable (not included) into the AUX IN Jack (#1) and the other end
of the cable to the head hone jack of your digital audio layer.
2. Turn on the SMPS-750 and your external audio device.
3. Press the MODE BUTTON (#12) re eatedly to select the AUX IN mode. ”LInE” will light
on the LED DISPLAY (#16).
4. The volume level can now be controlled through the main unit. O erate all other
functions on the auxiliary device as usual.
Notes:
• If you connect the SMPS-750 to the Line-Out Jack of your external device, you only
need to adjust the MASTER VOLUME CONTROL (#18) on your SMPS-750. If you
connect to the Head hone Jack of your external device, you may need to adjust both
the volume controls of your external device and the SMPS-750 to obtain the desirable
listening level.
• Remember to turn off the SMPS-750 when you have finished listening. Don't forget to
switch off the ower of your external audio device as well.

E-11
AUX OUT CONNECTION
You can connect the SMPS-750 to an external Hi-Fi / AMPLIFIER system by connecting the
AUX OUT JACK (#21) to the auxiliary in ut jack on your Hi-Fi / Am lifier system with 3.5mm
cable (included).
Now you can adjust both the volume control of your external Hi-Fi / AMPLIFIER system and
the MASTER VOLUME CONTROL (#18) of the SMPS-750 to find the most desirable volume
setting.
USING THE UNIT AS A PUBLIC ADDRESS SYSTEM
This unit can also be used as a PA (Public Address System).
1. Plug the micro hone or guitar (not included) into the MIC IN (#7)/GUITAR IN (#8) jack on
the to of the SMPS-750.
2. Turn on the SMPS-750.
3. Turn on your micro hone or guitar (not included) and start your erformance.
4. Adjust the MASTER VOLUME CONTROL (#18), MIC/GUITAR VOLUME (#11) and
ECHO CONTROL (#3) if necessary.
Note: To revent feedback or loud whistling from occurring, lease be sure that the
micro hone is not held too close to the s eakers on the SMPS-750.
RESETTING THE SMPS-750
In case of malfunction due to electrostatic discharge, reset the unit by disconnecting the DC
lug of the AC Ada ter from its rear DC IN JACK (#20). Wait at least for 3 minutes before
reconnecting the DC lug to the DC IN JACK (#20).
CARE AND MAINTENANCE
• Do not subject the unit to excessive force, shock, dust or extreme tem eratures.
• Do not tam er the internal com onents of the unit.
• Clean your unit with a dry cloth. Solvent or detergent should never be used.
• Avoid leaving your unit in direct sunlight or in hot, humid or dusty laces.
• Kee your unit away from heating a liances and sources of electrical noise such as
fluorescent lam s or motors.
CAUTION:
Never allow any water of other liquids to get inside the unit while cleaning.
Note: This unit is not magnetically shielded and may cause color distortion on the screen of
some TVs or video monitors. To avoid this, you may need to move the unit further away
from the TV or monitor if unnatural color shifts or image distortion occurs.

E-12
TROUBLESHOOTING
If you ex erience difficulties in the use of this music system, lease check the following or
call 1-800-777-5331 for Customer Service.
Fault
Possible Cause
s
Solution
s
No sound 1. No in ut sound source.
2. Volume is too low.
1. Use a better music signal.
2. Adjust volume.
Distortion of
sound
1. Volume too high.
2. The s eakers may be damaged.
1. Turn down the volume.
2. Contact Customer Service for
re air instructions.
Karaoke
does not
work
1. Micro hone lug is not fully
inserted.
2. Micro hone switch is not on.
3. Micro hone volume knob is too
low.
1. Plug micro hone ro erly into
the socket.
2. Turn on micro hone switch.
3. Increase the micro hone
volume.
MP3 does
not lay
1. The song format in the flash
drive is incom atible.
2. Im ro er o eration has caused
a rocess disorder.
3. Flash drive/SD card are
disconnected.
1.
Load MP3 songs into the flash
drive or SD card.
2. Turn off the machine and then
turn on again.
3. Insert flash drive/SD card
ro erly.
SPECIFICATIONS
Power requirement:
AC ada ter: In ut AC 120V ~ 60Hz
Out ut DC 15V 3A
Main Unit DC in ut: DC 15V 3A
Battery for Remote Control: 1 x 3V CR2025 Lithium Battery
Frequency Range
Radio Band: FM 87.5 ~ 108 MHz
At S ectra, environmental and social res onsibility is a core value
of our business. We are dedicated to continuous im lementation
of res onsible initiatives with an aim to conserve and maintain the
environment through res onsible recycling.
Please visit us at htt ://www.s ectraintl.com/green.htm for more information on S ectra’s
green initiatives or to find a recycler in your area.
The Bluetooth
®
word mark and logos are registered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by S ectra Merchandising International, Inc. is under license.
Other trademarks and trade names are those of their res ective owners.

E-13
90 DAY LIMITED WARRANTY AND SERVICE
VALID IN THE U S A ONLY
SPECTRA MERCHANDISING INTERNATIONAL, INC. warrants this unit to be free from
defective materials or factory workmanshi for a eriod of 90 days from the date of original
customer urchase and rovided the roduct is utilized within the U.S.A. This warranty is
not assignable or transferable. Our obligation under this warranty is the re air or
re lacement of the defective unit or any art thereof, exce t batteries, when it is returned to
the SPECTRA Service De artment, accom anied by roof of the date of original consumer
urchase, such as a du licate co y of a sales recei t.
You must ay all shi ing charges required to shi the roduct to SPECTRA for warranty
service. If the roduct is re aired or re laced under warranty, the return charges will be at
SPECTRA’s ex ense. There are no other ex ress warranties other than those stated herein.
This warranty is valid only in accordance with the conditions set forth below:
1. The warranty a lies to the SPECTRA roduct only while:
a. It remains in the ossession of the original urchaser and roof of urchase is
demonstrated.
b. It has not been subjected to accident, misuse, abuse, im ro er service, usage
outside the descri tions and warnings covered within the user manual or non-
SPECTRA a roved modifications.
c. Claims are made within the warranty eriod.
2. This warranty does not cover damage or equi ment failure caused by electrical wiring not
in com liance with electrical codes or SPECTRA user manual s ecifications, or failure to
rovide reasonable care and necessary maintenance as outlined in the user manual.
3. Warranty of all SPECTRA roducts a lies to residential use only and is void when
roducts are used in a nonresidential environment or installed outside the United States.
This warranty gives you s ecific legal rights, and you may also have other rights which vary
from state to state. TO OBTAIN SERVICE lease remove all batteries (if any) and ack the
unit carefully and send it freight re aid to SPECTRA at the address shown below. IF THE
UNIT IS RETURNED WITHIN THE WARRANTY PERIOD shown above, lease include a
roof of urchase (dated cash register recei t) so that we may establish your eligibility for
warranty service and re air of the unit without cost. Also include a note with a descri tion
ex laining how the unit is defective. A customer service re resentative may need to contact
you regarding the status of your re air, so lease include your name, address, hone
number and email address to ex edite the rocess.
IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD, lease include a check for $60 00
to cover the cost of re air, handling and return ostage. All out of warranty returns must be
sent re aid.
It is recommended that you contact SPECTRA first at 1-800-777-5331 or by email at
custserv@s ectraintl.com for u dated information on the unit requiring service. In some
cases the model you have may be discontinued, and SPECTRA reserves the right to offer
alternative o tions for re air or re lacement.
SPECTRA MERCHANDISING INTERNATIONAL, INC.
4230 North Normandy Avenue,
Chicago, IL 60634, USA.
1-800-777-5331
To register your roduct, visit the link on the website below to enter your information.
htt ://www.s ectraintl.com/wform.htm
0717 Printed in China