Jet 728200 Datasheet

JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-728200
Ph.: 800-274-6848 Edition 2 03/2022
www.jettools.com Copyright © 2022 JET
728200 Flip-Top Stand
Instructions and Parts List
IMPORTANT SAFETY INSTRUCTIONS
•Review all instructions before assembling the table.
Improper assembly can cause personal injury and/or
property damage.
•Do not exceed maximum load for the stand.
•Do not stand on this product.
•WARNING: This product can expose you to
chemicals including lead and cadmium which are
known to the State of California to cause cancer and
birth defects or other reproductive harm. For more
information go to http://www.p65warnings.ca.gov.
Tools required for assembly
10mm and 16mm wrenches
(a manual ratcheting socket wrench will speed
assembly time)
Shipping contents
1 Table Assembly
4 Lower Braces (2 Long, 2 Short)
4 Vertical Legs
4 Adjustment Legs
4 Leveling Pads
1 Instructions and Parts List
1 Product Registration Card
1 Hardware Package (728200-HP)
44 Carriage Bolt M6-1.0x16 –AA
44 Flat Washer 6mm–BB
44 Lock Washers 6mm –CC
44 Hex Nut M6-1.0–DD
Assembly instructions
Use the exploded view and parts list as guides to
assembly. Make all leg and brace fasteners only
finger tight until the entire unit has been assembled.
1. Turn table assembly upside down; use a mat or
piece of cardboard underneath to prevent
scratching.
2. Assemble the four main legs (#20) to the table
brackets (#8/26). Finger tighten only.
3. Determine the height desired, then connect the
adjustment legs (#21) to the main legs. These
can be repositioned later if needed. (It is
recommended that each adjustment leg be
secured by at least 4 screws to the main leg.)
4. Determine placement of lower braces (#24/25)
and assemble them to the main legs/adjustment
legs.
5. Install the leveling foot pads (#22) and tighten
each hex nut (#23) against the adjustment leg. (If
using the optional swivel casters, install those
instead of the pads.)
6. Turn the unit over and push down lightly to make
sure stand rests evenly upon the floor.
7. Fully tighten all fasteners. Take care to not
overtighten.
Holes are provided in the lower braces for attaching a
user-made shelf, not provided.

2
see page 4 for operating instructions
728200 Flip-Top Stand –Exploded View

3
To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m.
CST. Having the Model Number and Serial Number of your machine available when you call will allow us to serve
you quickly and accurately.
728200 Flip-Top Stand –Parts List
Index No. Part No. Description Size Qty
1.................TS-1541011 ................Nylon Lock Hex Nut.....................................................M5-0.8.............................2
2.................728200-002.................Flip-Top Table Locking Knob....................................... ........................................2
3.................728200-003.................Spring .......................................................................... ........................................2
4.................728200-004.................Long Pin....................................................................... ........................................2
6 ................TS-1541041 ................Nylon Lock Hex Nut.....................................................M10-1.5...........................2
7.....................TS-1550071 ................Flat Washer..................................................................10mm..............................2
8......................728200-008.................Flip-Top Table Bracket (L) (#8-1 thru 8-3) ................... ........................................1
8-1......................................................Support Plate............................................................... ........................................2
8-2......................................................Sleeve A....................................................................... ........................................2
8-3......................................................Sleeve B....................................................................... ........................................2
9.....................728200-009................. Spring .......................................................................... ........................................2
10...............TS-1522021 ................Socket Set Screw ........................................................ M5-0.8x8.........................2
11...................728200-011.................Pin................................................................................ ........................................2
12...................728200-012.................Flanged Hex Nut..........................................................M6-1.0.............................8
13...............728200-013................. Flip-Top Table Connecting Plate (#13-1 thru 13-2)...... ........................................2
13-1............ .................................... U Plate......................................................................... ........................................2
13-2............ .................................... Shaft ............................................................................ ........................................2
14...............728200-014.................Carriage Bolt................................................................M6-1.0x35.......................8
15...............728200-015.................Table (Plywood Top).................................................... ........................................1
15.0............728200-015.0..............Table Assembly (#1 thru 15, #26)................................ ........................................1
16...................728100-008.................Carriage Bolt................................................................ M6-1.0x16.....................44
17...............TS-1550041 ................Flat Washer..................................................................6mm..............................44
18...............TS-2361061 ................Lock Washer................................................................6mm..............................44
19...............TS-2311061 ................Hex Nut........................................................................M6-1.0...........................44
20 ..................728100-009................. Vertical Leg.................................................................. ........................................4
21...............728100-010.................Adjustment Leg Weldment (#21-1 thru 21-3)............... ........................................4
21-1...................................................Adjustment Leg............................................................ ........................................4
21-2...................................................Plate............................................................................. ........................................4
21-3............ .................................... Hex Nut........................................................................M10-1.5...........................4
22...................728100-012.................Bolt with Leveling Pad..................................................M10-1.5...........................4
23....................TS-2311101................Hex Nut........................................................................M10-1.5...........................4
24....................728100-013.................Lower Brace Short....................................................... ........................................2
25....................728100-014.................Lower Brace Long........................................................ ........................................2
26...................728200-026.................Flip-Top Table Bracket (R) (#8-1 thru 8-3)................... ........................................1
27...............728100-015.................JET Logo with Adhesive .............................................4.75”x3.3” ........................1
...................728200-030.................ID Label 728200 (not shown)....................................... ........................................1
...................728200-031.................Flip-Top Stand Decal (not shown)................................ ........................................1
...................728200-HP..................Hardware Package (#16 thru 19)................................. ........................................1
Optional Accessory* –Swivel Caster
28...............98-0129.......................Swivel Casters (set of 4).............................................. ..................................1 set
* Optional Accessory –see your dealer to order.

4
Operation
CAUTION: If the optional casters are used, make
sure they are locked in place.
To tilt table:
1. Pull out left and right handles and rotate them 90-
degrees to keep them disengaged.
2. Begin tilting front edge of table downward until it
just clears the handle pins, then turn handles 90-
degrees and allow them to slide back in.
3. Continue to tilt table slowly, while helping
stabilize the machine(s), until table passes the
beveled pins at the rear and snaps into level
position.
When machines are
mounted to table, tilt table slowly and help
stabilize the machines throughout the tilt
process. Do not allow the table to swing
uncontrollably. Failure to comply may cause
personal injury and/or unnecessary stress
upon stand components.
Machine selection
The stand will accept most bench top machines up to
load capacity and within the table size range (see
specifications). Secure the machine to the table with
appropriate fasteners (not provided). Make sure
machine(s) are securely fastened before attempting to
tilt the table.
Position of machines upon the table is user’s choice;
however, consideration should always be given to the
machines’ center of balance and weight distribution.
Ideally, they are centered upon the table. But the
design of some machines may require them to be
shifted off center for optimum position and/or easier
tilting to the down position.
(machines and user-made shelf not provided)
Specifications for JET Flip-Top Stand
Stock number
728200
Table size (D x W)
20 x 25 in. (508 x 635 mm)
Height range
29 to 34 in. (736.6 to 863.6 mm)
Height adjustment
5.10 in. (130 mm)
Load capacity
300 lb. (136 kg)
Table material
MDF/Vinyl
Assembled weight
45 lb. (20 kg)
Shipping weight
49 lb. (22 kg)
The 728200 Flip-Top Stand will accommodate most bench top machines, including the following models:
Brand
Model
Stock No.
Notes
JET
13” Planer
722130
JET
8” Jointer/Planer
707400
JET
8” Grinder
726101
JET
1020 Drum Sander
723510
JET
9” Belt/Disc Sander
708595
JET
Spindle Sander 5”
708404
JET
18” Scroll Saw
727300B
JET
22” Scroll Saw
727200B
JET
10” Miter Saw
707210
Secure miter arm before tilting underneath.
JET
12” Miter Saw
707212
Secure miter arm before tilting underneath.
JET
JET Mortiser
708580
Remove handle if needed before tilting underneath.
Powermatic
PM Mortiser
1791310
Remove handle if needed before tilting underneath.
JET
10” Band saw
714400
JET
12” Drill Press
716000
JET
15” Drill Press
716200
Powermatic
PM1250 Air Filtration
1791250