JETWAY 994ANR4A User manual

994AN/994AN-L
994AS/994AS-L
USER'S MANUAL
PCI/ AGP Mainboard
For Pentium

II/ III or Socket 370
The author assumes no responsibility for any errors or omissions which
may appear in this document nor does it make a commitment to update
the information contained herein.
NO. G03-994ANR4A
Release date: NOV 2000
** Year 2000 compliant **
Trademark:
* Pentium is registered trademark andMMX is a trademark of Intel corporation,
the other names and brands are the property of their respective owners.
* Specifications and Information contained in this documentation are furnished for information use only, and are subject to
change at any time without notice, and should not be construed as a commitment by manufacturer.

i
Chapter 1
1-1 Preface.............................................................................................................1
1-2 Feature of motherboard....................................................................................1
1-2-1 Overview..............................................................................................1
1-2-2 Key Feature.........................................................................................2
Chapter 2
Hardware Installation..................................................................................3
2-1 Unpacking........................................................................................................3
2-2 Mainboard Diagram..........................................................................................4
2-3 Quick Reference for Jumpers, Connectors & Expansion Socket.......................5
2-4 Installation Steps..............................................................................................6
2-5 Jumper Settings ...............................................................................................6
2-6 System Memory (DRAM)..................................................................................7
2-7 Central Processing Unit (CPU).........................................................................7
2-8 Expansion Cards..............................................................................................10
2-9 External Connectors.........................................................................................11
Chapter 3
AWARD BIOS SETUP..................................................................................17
3-1 STANDARD CMOS FEATURES......................................................................18
3-2 ADVANCED BIOS FEATURES........................................................................19
3-3 ADVANCED CHIPSET FEATURES .................................................................21
3-4 INTEGRATED PERIPHERALS.........................................................................22
3-5 POWER MANAGEMENT SETUP ....................................................................23
3-6 PnP/PCI CONFIGURATIONS ..........................................................................24
3-7 PC HEALTH STATUS......................................................................................25
3-8 FREQUENCY/VOLTAGE CONTROL...............................................................26
3-9 LOAD OPTIMAL DEFAULTS............................................................................26
3-10 LOAD STANDARD DEFAULTS........................................................................27
3-11 SET SUPERVISOR/USER PASSWORD .........................................................27
3-12 SAVE & EXIT SETUP/EXIT WITHOUT SAVING..............................................27
Chapter 4
Software Installation............................................................................................28
4-1 Mainboard Driver Install in Win9X,WinNT.........................................................28
4-2 PC HEALTH MONITOR-III................................................................................29
4-3 SOUND Driver (Option for motherboard that embedded Audio chip)................31
APPENDIX-A Magic Install........................................................................46
TABLE OF CONTENT

1
Chapter 1
1-1 Preface
Thank you for purchasing this multifunction motherboard. It has the most flexibility you can find
in today’s computer market. The mainboard integrates both Intel Pentium®II / Pentium®III &
Celeron™(Slot 1) / Coppermine processor and Celeron™ (Socket 370) PPGA / FCPGA
processor interface into a compact PC/ATX compatible system along with next generation of 4X
AGP specification, 133MHz FSB, Ultra DMA66, and optional 3D Stereo Sound System audio
chip. Moreover, this mainboard allows you conditionally approach 140MHz* of Front Side Bus
Frequency to accelerate your CPU speed.
1-2 Feature of motherboard
This motherboard is design for the PC user who wants highest possible quality and value in a
small package. It includes following main features：
1-2-1 Overview
•Support both Slot 1 & Socket 370 CPU interface (You can only use one CPU interface
at a time).
•Support Ultra DMA 66 for newer hard disk interface.
•Support Jump-less solution for setting Front Side Bus Frequency (CPU Host Clock)
and CPU ratio under CPU Host/PCI clock of CHIPSET FEATURES SETUP.
•Support CPU Host Clock and DRAM Clock Asynchronous/Synchronous mode, please
refer page 25 “ DRAM Clock”.
•Conditionally support 66MHz~140MHz* of Front Side Bus Frequency. This function
allow user select CPU Bus Frequency by the BIOS to approach Over-Clock possibility.
•Provide PC Health Monitoring to track CPU temperature, system temperature, system
voltage, and fan speed. When CPU current temperature is over CPU warning
temperature, system will slow down automatically in order to reduce the CPU’s
temperature. (Option for motherboard that embedded PC Health chip)
•Logo-DIY: Provide CBROM utility for user to create their own loge in the BIOS.
•Built in high quality PCI-Based HRTF 3D Extension Positional Audio Chip (Option for
motherboard that embedded Audio chip)
-Supports rear side speakers, C3DX positional audio in 4 channels speaker mode.
-Professional digital audio interface to support 24-bit SPDIF IN and OUT (44.1K and 48K
format).
-HRTF-base 3D positional audio, supporting DirectSound™ 3D and Aural A3D™ interface.
- Digital functions that capable to provide hi-fi stereo, Dolby, 3D surround effects, and
playing MP3 music.
•You can add our Optical kit (Option for motherboard that embedded Audio chip) to
connect any optical Input/Output device for super high quality sound transaction,
such as playing & recording MD(Mini Disk)/CD; CD-ROM directly recording to MD;
combine with DVD player to create a home theater system (This upgrade kit includes
Optical Module, Optical Cable, and Software DVD Driver).
1-2-2 Key Feature

2
•Multi-Speed Support ：Provide 66/75*/83*/95*/100/112*/117*/124*/133*/140*MHz Front
Side Bus Frequency to support Intel Pentium®II / Pentium®III / Coppermine / Celeron
processor for Slot1 interface or Intel Celeron PPGA / FCPGA on a ZIP Socket 370 interface.
•Chipset：VIA 82C694X Apollo Pro-133A Chipset.
•DRAM Memory Support：Support 3 x 168-pin DIMM sockets (3.3V) for memory from 8M
Byte to 1.5GB Byte in either EDO (66MHz only) or SDRAM (66MHz/100MHz/133 MHz) type
module with ECC or parity check.
•AGP, ISA, and PCI expansion Slots：Provide a 4X AGP slot, one 16-bit ISA slot, and four
32-bit PCI master slots.
•Super Multi-I/O: Provides two high-Speed UART compatible serial ports and one parallel
port with EPP and ECP capabilities. Two floppy drives of either 5.25” or 3.5” (1.44MB or
2.88MB) are also supported without an external card.
•PCI Bus Master IDE Controller and ULTRA DMA 33/66 : On-board PCI Bus Master IDE
controller with two connectors that supports four IDE devices in two channels, provides
faster data transfer rates, and supports Enhanced IDE devices such as Tape Backup, CD-
ROM, ZIP,LS-120 Drives. This controller also supports PIO Modes and Bus Master IDE
Ultra DMA 33/66Mbyte/Second.
•ACPI supporting for OS Directed Power Management.
Ring-In Wake up: When Ring-In the system can wake up from SMI Mode.
Ring-In Power On: When Ring-In the system can power on automatic by this function.
RTC Power On: Enabled RTC Power On function, you can set RTC alarm to power on the
system at the time length that correspond to your setting.
Power Button: Press the button will place the system power on/off.
Wake on LAN : The system can power on by server in Network.
Support Software Power Off function.
•Power Support: Efficient PWM switching power instead of traditional Linear Voltage
Regulator to prevent power component from being burned-out.
•PC 99 ready
•PS/2 Mouse: This mainboard support PS/2 mouse set.
•USB Port Connector: This mainboard supports two USB port connectors for USB devices.
•Optional IrDA: This mainboard supports an optional infrared port module for wireless
interface, with independent 3rd UART (32-byte FIFO).
•4X AGP: Accelerated Graphics Port to support up to 1GB/sec data transfer rate and
266MHz 4X mode for AD and SBA signaling.
•ATX Form Factor: Dimensions 30.5cm x 19cm.
* Your memory module(s) must be PC133 compliant SDRAM chips and specified to run
on 133MHz or 140MHz.
* When you are running at 140MHz, make sure all of your PCI devices have enough
tolerance to run on 37.5MHz . Otherwise, it may cause your system become very
unstable. Chapter 2

3
Hardware Installation
2-1 Unpacking
This mainboard package should contain the following:
•The mainboard
•USER’S MANUAL for mainboard
•Cable set for Ultra DMA 66 IDE x1, Floppy x1
•CD for Drivers PACK
The mainboard contains sensitive electronic components that can be easily damaged by
electron-static, so the mainboard should be left in its original packing until it is installed.
Unpacking and installation should be done on a grounded anti-static mat.
The operator should be wearing an anti static wristband, grounded at the same point as the anti-
static mat.
Inspect the mainboard carton for obvious damage. Shipping and handling may cause damage to
your board. Be sure there are no shipping andhandling damages on the board before proceeding.
After opening the mainboard carton, extract the system board and place it only on a grounded
anti-static surface component side up. Again inspect the board for damage.
Press down on the entire socket IC’s to make sure that they are properly inserted. Do this only
on with the board placed on a firm flat surface.
Warning: Do not apply power to the board if it has been damaged.
You are now ready to install your mainboard. The mounting hole pattern on the mainboard
matches the ATX system board.
It is assumed that the chassis is designed for a standard ATXmain board mounting. Place the
chassis on the anti-static mat and remove the cover.
Take the plastic clips, Nylon stand-off and screws for mounting the system board, and keep
them separate.
2-2 Mainboard Diagram

4
U8
SLOT-1
J3
MINI-
DIN
COM2
COM2 COM1
POR
T
J5
J2
+
BATT.
BT1
VIA82C694X
U12
VIA82C596B
U17
J1
US
B
J4
ATX POWER CONN.
PL1
IDE2
IDE2
IDE1
PCI 2
PCI2
PCI 1
P
C
I1
MIC LINE-I
N
LINE-OUT
AGC
GAME1
PCI3
PCI 3
PCI4
P
C
I 4
ZIF SOCKET 370
CP
U
U10
DIMM2
DIMM3
DIMM2
DIMM3
DIMM1
DIMM1
SL1
JP15
AG
P1
AGP
J
P2
J
P
3
IR1
JP16
SYSFAN
IDE1
CPUFAN
BIOS
U4
FDD
FDD
JP9
WOL
KEYLOCK
RST TBLE
D
TBSW
HDLED
PS-ON
SPEAKER
CMI8738
U7
SMI
U20
U19
ALI M5135
U3
SPDIFIN 1
JP1 SPDIFOUT
J
P4
SPKIN 1
Figure 2-2
Option for motherboard that embedded with Audio Chip
2-3 Quick Reference for Jumpers, Connectors & Expansion Socket
Jumpers

5
Jumper Name Description Page
U19 CPU Bus Frequency Selection Refer to page 6 p. 6
U20 CPU Ratio Selector Refer to page 6 p. 6
JP16 CMOS RAM Clear 1-2 Normal ,2-3 Clear CMOS p. 7
Connectors
Connector Name Description Page
PL1 ATX Power Connector 20-Pin Block p.9
MINI-DIN PS/2 Keyboard/PS/2 Mouse 6-Pin Female p.9
USB USB Port Connector 5-Pin Connector p.9
PRINT Parallel Port Connector 26-Pin Female p.9
COM1, COM2 Serial Port COMA , COMB 9-Pin Connector p.10
FDD Floppy Driver Connector 34-Pin Block p.10
IDE1 Primary IDE Connector 40-Pin Block p.10
IDE2 Secondary IDE Connector 40-Pin Block p.10
HDLED IDE activity LED 2-Pin Connector p.11
SMI SMI Suspend Switch 2-Pin Connector p.11
JP15 Front Panel Connector 16-Pin Block p.11
IR1 Infrared Module Connector 10-Pin Block p.12
CPUFAN, SYSFAN FAN Connector Extra fanning system connectors p.12
PS-ON ATX power button/soft power button 2-Pin Connector p.12
WOL Wake On LAN 3-pin Block P.12
Jumpers & Connectors (Option for motherboard that embedded Audio chip)
Item number Name Description Page
JP4 On-Board Sound Enable/Disable 1-2 : Disabled , 2-3 : Enabled p.13
JP1 AUX IN 4-pin Block p.13
JP2 CD-Audio 4-pin Block p.13
JP3 CD-Audio 4-pin Block p.13
AGC Line IN/Line Out/MIC /Game Connector 15-pin Connector + 3 phone jack p.13
SPKIN 1 PC Speaker In 2-pin Block p.14
SPDIFIN 1 SPDIF (Sony/Philips Digital Interface) IN 3-pin Block p.14
SPDIFOUT SPDIF (Sony/Philips Digital Interface) OUT 2-pin Block p.14
JP9 For Optional Optical Kit Connector 10-pin Connector p.14
Expansion Sockets
Socket/Slot Name Description
DIMM1,DIMM2, DIMM3 DIMM Module Socket 168-Pins DIMM SDRAM Module Expansion Socket
Slot1 CPU Slot Pentium II/III / Coppermine CPU Slot
Zip Socket370 CPU Socket Celeron PPGA / FCPGA CPU Socket
AGP SLOT 4X AGP SLOT AGP Expansion Slot
PCI1, PCI2,PCI3 ,PCI4 PCI Slot 32-bit PCI Local Bus Expansion slots
SL1 ISA Slot 16-bit ISA Bus Expansion slot
2-4 Installation Steps
Before using your computer, you must follow the steps as follows:
1. Set Jumpers on the Mainboard

6
2. Install the CPU
3. Install DRAM Modules
4. Install Expansion card
5. Connect Cables, Wires, and Power Supply
2-5 Jumper Settings
1. CPU Bus Frequency Selection : U19
U20
5678
1234
U19
1234
5678
•Users also can setting the CPU Bus frequency in the “CPU Host/PCI clock” in
CHIPSET FEATURES SETUP.(Please refer to page 25)
2. CPU Ratio Selector：U20
Ratio 1-5 2-6 3-7 4-8 Ratio 1-5 2-6 3-3 4-8
3.0x ON OFF ON ON 5.5x OFF OFF OFF ON
3.5x OFF OFF ON ON 6.0x ON ON ON OFF
4.0x ON ON OFF ON 6.5x OFF ON ON OFF
4.5x OFF ON OFF ON 7.0x ON OFF ON OFF
5.0x ON OFF OFF ON 7.5x OFF OFF ON OFF
8.0x ON ON OFF OFF
Table for the Pentium III and Celeron Socket 370 CPU
Celeron Pentium III Pentium III
Speed Bus Ratio Speed Bus Ratio Speed Bus Ratio
300/66 66MHz 4.5x 500E/100 100MHz 5.0x 733/133 133MHz 5.5x
333/66 66MHz 5.0x 533EB/133 133MHz 4.0x 750/100 100MHz 7.5x
366/66 66MHz 5.5x 550E/100 100MHz 5.5x 800/100 100MHz 8.0x
400/66 66MHz 6.0x 600E/100 100MHz 6.0x 800EB/133 133MHz 6.0x
466/66 66MHz 7.0x 600EB/133 133MHz 4.5x 850/100 100MHz 8.5x
500/66 66MHz 7.5x 650/100 100MHz 6.5x 866/133 133MHz 6.5x
533/66 66MHz 8.0x 667/133 133MHz 5.0x 933/133 133MHz 7.0x
533A/66 66MHz 8.0x 700/100 100MHz 7.0x 1.0GHz/133 133MHz 7.5x
566/66 66MHz 8.5x
600/66 66MHz 9.0x
633/66 66MHz 9.5x
667/66 66MHz 10.0x
700/66 66MHz 10.5x
733/66 66MHz 11.0x
766/66 66MHz 11.5x
∗Because the Ratio are fixed by CPU Manufacture, users don’t need
to setting ratio any more, this table just for reference use.
2. CMOS RAM Clear: JP16 (Yellow color selector)
WARNING: Make sure your computer is POWER OFF when you CLEAR CMOS.
CPU External Frequenc
y
：U19
CPU 1-5 2-6 3-7 4-8
66.8 OFF OFF ON ON
75 OFF ON ON ON
83 ON OFF ON ON
100 OFF OFF OFF ON
124 ON OFF OFF OFF
133 OFF OFF OFF OFF
*Your Memory must meet the requirement to run on 133MHz or 140MHz
condition. In order to run 140MHz, Please set jumper at 133MHz condition and
then change the setting to140MHz from the BIOS.

7
Connect a jumper Cap over this jumper for a few seconds, will clears information stored in the
CMOS RAM Chip that input by user, such as hard disk information and passwords. After
CLEAR CMOS, you must enter the BIOS setup (by holding down <DEL> during power-up) to re-
enter BIOS information (see BIOS SETUP).
Selections JP16
Normal 1-2 (Default)
Clear CMOS 2-3 (momentarily)
CMOS RAM
(
Normal / Clear CMOS Data
)
JP16 JP16
Normal
1
2
3
Clear CMOS
1
2
3
2-6 System Memory (DRAM)
This mainboard supports three 168-pins DIMM modules, the Max Memory Size is 1.5GByte.
DIMM 1 DIMM 2 DIMM 3 System can be Accept or Not
168-pin DIMM x x Accept
168-pin DIMM 168-pin DIMM x Accept
168-pin DIMM 168-pin DIMM 168-pin DIMM Accept
2-7 Central Processing Unit (CPU)
2-7-1 The mainboard provides a Slot-1 for Pentium II/III processor. The CPU on board must
have a fan or heat sink attached to prevent overheating.
WARNING: Without a fan or heat sink, the CPU will overheat and cause damage to both the CPU
and the mainboard.
To install a CPU, first turn off your system and remove its cover. Locate the Slot- 1 and place
RETENTION MODULE as following:
IMPORTANT: You must set jumper U19,U20 for “Bus Frequency Selection” and “CPU Ratio” on
page6 depending on the CPU that you install.
1. Attach heat sink to the CPU.
2. Place Part A on Slot-1 and gently screw four corners on top of the main- board.
PART A
2-7-2 The mainboard also provides a 370-pin ZIF Socket 370. The CPU on mainboard must
have a fan attached to prevent overheating.
To install a CPU, first turn off your system and remove its cover. Locate the ZIF Socket and
open it by first pulling the lever sideways away from the socket then upwards to a 90-degree

8
right angle. Insert the CPU with the white dot as your guide. The white dot should point towards
the end of the level. The CPU has a corner pin for three of the four corners, the CPU will only fit
in the one orientation as shown as follow. With the added weight of the CPU fan, no force is
required to insert the CPU. Once completely inserted, hold down on the fan and close the
Socket’s lever.
IMPORTANT: You can setting the CPU ratio and Host Frequency in the BIOS setup on page 18
CPU ZIF Socket 370
Lock
Socket 370
Blank
Lever
White Dot
Socket 370
CPU
2-7-3 Intel®Pentium®III Processor (256K) in the FC-PGA form factor: Mechanical Features
The FC-PGA package has the processor’s silicon die directly mounted to a pinned interposer substrate.
The pin grid array is partially populated and there may be surface mount components in the unpopulated
central area of the pin field.
Intel®Pentium®III Processor in the FC-PGA form factor: Mechanical Features
Reference Design: Heatsink
Substrate
Flip Chip Die
Pins
Fillet Epoxy
(Not to scale)
Flip-Chip Si Core
C4 Solder bumps
Surface mounted
pins
Fillet Epoxy
(Not to scale)
Multi-layer
substrate
FC-PGA with the reference
design heatsink
zIntel’s reference design thermal solution is an
active heatsink; an extruded aluminum heatsink
base and a fan attached to the top on the fin
array.
• Heatsinks for the PPGA will not work with the
FC-PGA. A pedestal is required on the
underside of the heatsink to clear the socket
cam box
zRecommended thermal interface
material: Chomerics* XTS454.

9
Heatsink Attachment
FC-PGA with a PPGA heatsink
CPU Insertion Step 1
Open the socket by raising the actuation lever.
Step 2
Insert the processor.
Ensure proper pin 1 orientation by aligning the FC-PGA
corner marking with the socket corner closest to the
actuation arm tip. The pin field is keyed to prevent mis-
oriented insertion.
Don’t force processor into socket. If it does not go in easily,
check for mis-orientation and debris.
Make sure the processor is fully inserted into the socket
on all sides.
Step 3
Close the socket by lowering and locking the actuation lever.
Step 1
Remove the protective liner from the thermal interface
material on the underside of the heatsink.
This liner is not normally present on the Intel reference
active heatsink.
Step 2
Orient the heatsink with the keyed edge of
heatsink along the cam box side of the
processor.
The clip should be oriented so that the thumb tab will
engage on the cam box side of the socket.
Step 3
Seat the heatsink onto the processor and
engage the clip opposite from the cam box onto

10
2-8 Expansion Cards
You must read the documentation come with expansion card for any hardware or software
settings that may be required to setup your specific card.
Installation Procedure:
1. Read the documentation from your expansion card.
2. Set any necessary jumpers on your expansion card.
3. Remove your computer’s cover.
4. Remove the bracket on the slot you intend to use.
5. Carefully align the card’s connectors and press firmly.
6. Secure the card on the slot with the screw you remove in step 4.
7. Replace the computer’s cover.
8. Setup the BIOS if necessary.
9. Install the necessary software drivers for your expansion card.
Assigning IRQs for Expansion Cards
Some expansion cards may require an IRQ to operate. Generally an IRQ must be exclusively
assigned to only one device. In an standard design there are 16 IRQs available but most of
them are occupied by the system and leaves 6 free for expansion cards.
With most recent device, the BIOS automatically assign an IRQ number to PCI expansion cards.
Please make sure there are no any of two devices use same IRQs, otherwise your computer
may experience some problems when those two devices are in use at the same time.
Assigning DMA Channels for Expansion Cards

11
Some devices may also need to use a DMA (Direct Memory Access) channel. DMA
assignments for this mainboard are handled the same way as the IRQ assignment process
described above. You can select a DMA channel in the PCI and PnP configuration section of the
BIOS Setup utility.
2-9 External Connectors
1. Power Connector: ATX Power Connector (20-pin block): PL1
ATX Power Supply connector. This is a new defined 20-pins connector that usually comes
with ATX case. The ATX Power Supply allows to use soft power on momentary switch that
connect from the front panel switch to 2-pins Power On jumper pole on the mainboard.
When the power switch on the back of the ATX power supply turned on, the full power will
not come into the system board until the front panel switch is momentarily pressed. Press
this switch again will turn off the power to the system board.
PIN ROW2 ROW1
1 3.3V 3.3V
2 -12V 3.3V
3 GND GND
4 Soft Power On 5V
5 GND GND
6 GND 5V
7 GND GND
8 -5V Power OK
9 +5V +5VSB (for Soft Logic)
10 +5V +12V
ATX Power Connector
PIN 1
2. PS/2 Mouse & PS/2 Keyboard Connector: MINI-DIN
The connectors for PS/2 keyboard and PS/2 Mouse.
3. USB Port connector: USB
The connectors are 4-pins connector that connect USB devices to the system board.
USB Port Connector
USB
4. Parallel Port Connector (25-pin female): PRINT
Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The On-board
Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3
“INTEGRATED PERIPHERALS SETUP” section for more detail information.
PS/2 Keyboard
PS/2 Mouse

12
Parallel Port Connector
5. Serial Port COMA, COMB: COM1, COM2
COMA is the 9-pin D-Subminiature mail connector. The On-board serial port can be disabled
through BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHERALS SETUP”
section for more detail information.
COM1
Serial
p
ort COMA,COMB Connector
COM2
6. Floppy drive Connector (34-pin block): FDD
This connector supports the provided floppy drive ribbon cable. After connecting the single plug
end to mainboard, connect the two plugs at other end to the floppy drives.
Floppy drive Connector
Pin 1
7. Primary IDE Connector (40-pin block): IDE1
This connector supports the provided IDE hard disk ribbon cable. After connecting the single
plug end to mainboard, connect the two plugs at other end to your hard disk(s). If you install
two hard disks, you must configure the second drive to Slave mode by setting its jumpers
accordingly. Please refer to the documentation of your hard disk for the jumper settings.
Primary IDE Connector
Pin 1
8. Secondary IDE Connector (40-pin block): IDE2
This connector connects to the next set of Master and Slave hard disks. Follow the same
procedure described for the primary IDE connector. You may also configure two hard disks

13
to be both Masters using one ribbon cable on the primary IDE connector and another ribbon
cable on the secondary IDE connector.
Secondar
y
IDE Connector
Pin 1
9. IDE activity LED: HDLED
This connector connects to the hard disk activity indicator light on the case.
IDE (Hard Drive) LED
HDLED
10.SMI Switch : SMI
If your case has Suspend switch , you may connect the cable to this connector in order to
have Suspend mode control from your case.
SMI Switch
SMI
11. Turbo LED switch: TBLED
The mainboard‘s turbo function is always on. The turbo LED will remain constantly lit while
the system power is on. You may wish to connect the Power LED from the system case to
this lead. See the figure below.
12. Reset switch lead: RST
This 2-pin connector connects to the case-mounted reset switch for rebooting your computer
without having to turn off your power switch. This is a preferred method of rebooting in order
to prolong the life of the system‘s power supply. See the figure below.
13. Keyboard lock switch lead: KEYLOCK
This 5-pin connector connects to the case-mounted key switch for locking the keyboard for
security purposes. See the figure below.
14. Speaker connector: SPEAKER
This 4-pins connector connects to the case-mounted speaker. See the figure below.

14
System Case Connections
GND
GND
GND Turbo LED
Reset SW
Ke
y
board
Lock
Power LED
V
CC
VCC
GND
Turbo SW
VCC
NC
GND
GND
NC Speaker
15. IR infrared module connector: IR1
This connector supports the optional wireless transmitting and receiving infrared module.
This module mounts to small opening on system cases that support this feature you must
also configure the setting through BIOS setup. Use the four pins as shown on the Back View
and connect a ribbon cable from the module to the mainboard according to the pin definitions.
SIR
IR1
IR Infrared Module Connector
16. FAN connector: CPUFAN , SYSFAN
SYSFAN
CPUFAN
FAN Connector
17. Power-On button connector: PS-ON
2
4
GND
Push Button
Power-On button connector
18. Wake On Lan connector: WOL
WOL
+
5VSB GND WON

15
JP2 :CD-Adio/Panasonic JP3 :CD-Audio/Sony
JP2
JP3
※Wake On LAN Function worked only when power supply support 5VSB more than 750mA
current.
Jumpers & Connectors (Option for motherboard that emedded Audio chip)
19. On Board Audio chip Enabled / Disabled connector: JP4
2-3 closed: Enabled 1-2 closed: Disabled
JP4
1
3
1
3
20. Auxiliary Input connector: JP1
21. CD Audio in connector : JP2,JP3
JP2 and JP3 are the connectors for CD-Audio Input signal, Please connect it to CD-ROM
CD-Audio output connector
22. Audio and Game Connector : AGC
This Connector are 3 phone Jack for LINE-OUT,LINE-IN,MIC and a 15-pin
D-Subminiature Receptacle Connector for joystick/MIDI Device.
Line-out : audio output to speaker
Line-in : audio input to sound chip (Please plug here for second pair speakers as output
channels when use 4 speakers)
MIC : Microphone Connector
Game/MIDI : for joystick or MIDI Device
Audio and Game Connector
LINE-OUT MICLINE-IN
Game / MIDI PORT
JP1

16
23. PC Speaker signal Input connector: SPKIN 1
SPKIN 1
24. SPDIF (Sony / Philips Digital Interface) Input / Output Connectors: SPDIFIN 1 /
SPDIFOUT
SPDIFIN 1 SPDIFOUT
SPDIFOUT
+5V
GND
SPDIFIN GND
25. Optical kit connector: JP9
This connector is for user that has Optical kit(optional) to provide other set of SPDIF
INPUT and SPDIF OUTPUT function.
O
p
tical kit Connector
JP9
1
2
9
10
Chapter 3
AWARD BIOS SETUP
This mainboard has previously set to its best stable status. If you are not an experienced user,
please do not change the default setting. When you are encounter any problem, please choice
“LOAD STANDARD DEFAULTS” to restore best setting.

17
Award’s ROM BIOS provides a built-in Setup program which allows user modify the basic system
configuration and hardware parameters. The modified data will be stored in a battery-backed
CMOS RAM so data will be retained even when the power is turned off. In general, the
information saved in the CMOS RAM stay unchanged unless here is configuration change in the
system, such as hard drive replacement or new equipment is installed.
It is possible that CMOS had a battery failure which cause data lose in CMOS_RAM. If so, re-enter
system configuration parameters become necessary.
To enter Setup Program
Power on the computer and press <Del> key immediately will bring you into BIOS CMOS
SETUP UTILITY.
CMOS Setup Utility – Copyright ( C ) 1984-1999 Award Software
Standard CMOS Features
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
Frequency/Voltage Control
Load Optimal Defaults
Load Standard Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
Esc : QUIT F 9: Menu in BIOS ↑↓←→ : Select Item
F10 : Save & Exit Setup
Time, Date, Hard Disk Type….
Figure 3
Note that a brief description of each highlighted selection is listed below. The main menu
includes the following setup categories. Please recall that some systems may not include all
entries.
Standard CMOS Features: Use this menu for basic system configuration. See Section 3-1
for the details.
Advanced BIOS Features: Use this menu to set the Advanced Features available on your
system. See Section 3-2 for the details.
Advanced Chipset Features: Use this menu to change the values in the chipset registers
and optimize your system's performance. See section 3-3 for the details.
Integrated Peripherals: Use this menu to specify your settings for integrated peripherals.
See section 3-4 for the details.
Power Management Setup: Use this menu to specify your settings for power management.
See section 3-5 for the details.
PnP / PCI Configuration: This entry appears if your system supports PnP / PCI. See
section 3-6 for the details.
PC Health Status: Use this menu to show the temperature, FAN Speed, Voltage of the PC
Health. 3-7 for the details.
Frequency/Voltage Control: Use this menu to specify your settings for frequency/voltage
control. See section 3-8 for the details.

18
Load Optimal Defaults: Use this menu to load the Optimal default values for the higher
performance for your system to operate. See section 3-9 for the details.
Load Standard Defaults: Use this menu to load the BIOS default values that are factory
settings for normal/stable performance system operations. While Award has designed the
custom BIOS to normal/stable performance, the factory has the right to change these
defaults to meet their needs. See section 3-10 for the details.
Supervisor / User Password: Use this menu to set User and/or Supervisor Passwords.
See section 3-11 for the details.
Save & Exit Setup: Save CMOS value changes to CMOS and exit setup. See section 3-12
for the details.
Exit Without Save: Abandon all CMOS value changes and exit setup. See section 3-12 for
the details.
3-1 STANDARD CMOS FEATURES
The items in Standard CMOS Features Menu are divided into many categories, and each category may
includes more than one setup items. Please use the arrow keys to highlight the item and then use the
<PgUp> or <PgDn> keys to select the value you want in each item.
CMOS Setup Utility-Copyright © 1984-1999 Award Software
Standard CMOS Features
Date: (mm:dd:yy) Fri, DEC 10 1999
Time: (hh:mm:ss) 10:52:22
¾IDE Primary Master Press Enter None
¾IDE Primary Slave Press Enter None
¾IDE Secondary Master Press Enter None
¾IDE Secondary Slave Press Enter None
Drive A 1.44M, 3.5 in.
Drive B None
Video EGA/VGA
Halt On All Errors
Based Memory 640K
Extended Memory 60416K
Total Memory 61440K
Item Help
Menu Level ¾
Change the day, month,
year and century
↑↓←→Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 3-1
IDE Adapters: The IDE adapters control the hard disk drive. Use a separate sub menu to
configure each hard disk drive. Diagram below shows the IDE primary master sub menu.
CMOS Setup Utility – Copyright © 1984-1999 Award Software
IDE Primary Master