JETWAY HPC150R-DCP6305E Series User manual

Panel PC
User’s Manual
NO. G03-PCLZ0FRFP-F
Manual Revision: 1.0
Release Date：2022/03/03

i
Safety Precautions............................................................................................................................... ii
User’s Notice..........................................................................................................................................iii
Package Contents.................................................................................................................................iii
Environmental Protection Announcement .................................................................................. iii
Chapter 1 Introduction......................................................................................................................1
1-1 General Descriptions...........................................................................................................1
1-2 Specifications........................................................................................................................ 2
1-3 I/O Outlets...............................................................................................................................4
1-4 Connector Description........................................................................................................5
Chapter 2 Hardware and Installation............................................................................................ 7
2-1 Dimensions and Outlines................................................................................................... 8
2-2 To Open the Chassis........................................................................................................... 9
2-3 Jumper Settings....................................................................................................................10
2-4 Hardware Installation...........................................................................................................13
2-4-1 To Install SO-DIMM to the Board........................................................................13
2-4-2 To Install M.2 M-Key Card.................................................................................... 14
2-4-3 To Install M.2 E-Key Wi-Fi Card..........................................................................15
2-4-4 To Install M.2 B-Key Card along with Nano-SIM Card..................................18
2-4-5 To Install HDD......................................................................................................... 21
Chapter 3 Introducing BIOS............................................................................................................ 22
3-1 Entering Setup..................................................................................................................... 21
3-2 BIOS Menu Screen.............................................................................................................. 23
3-3 Function Keys...................................................................................................................... 23
3-4 Getting Help.......................................................................................................................... 23
3-5 Menu Bars............................................................................................................................. 24
3-6 Main Menu............................................................................................................................. 24
3-7 Advanced Menu................................................................................................................... 25
3-8 Chipset Menu........................................................................................................................34
3-9 Security Menu.......................................................................................................................36
3-10 Boot Menu............................................................................................................................. 37
3-11 Save & Exit Menu.................................................................................................................38
APPENDIX...............................................................................................................................................39
TABLE OF CONTENT

ii
Safety Precautions
Operate the product according to the correct installation steps and with great care to make sure
safety and comfort using experience. Please refer to the following safety instruction guide to avoid
danger of electric shock or fire. Abide by the previous safety instruction guide to use and maintain
the product and the hard disk to make sure of safe operating environment.
Please follow the instruction manual for operation guide.
The appropriate operating temperature ranges from 0 °C–50 °C.
The operation humidity for this product is 5% to 80% RH.
To avoid high temperature, please DO NOT overload the maximum power of the external power
supply while the system is consuming high voltage. Be aware of the maximum temperature
allowance of the power supply.
See to it that the product is not working near the water.
Always unplug power cable and other hardware cables from the system before cleaning.
Apply only dry cloth for cleansing the product.
Make sure that there is no heat source nearby when the product is working.
Make sure that the thermal louver of the product is not blocked.
Make sure to remove the power plug from the product when there is a thunder storm.
Please remove the power plug from the product when you are not going to use the product for a
long time.
Make sure to set up or use the product on a stable surface.
Make sure not to drop the product or strike it by any means.
Make sure not to move the product when the power is on.
Make sure not to step on the power cables and other cables or rest anything in them..
Be sure to ground yourself to prevent static charge when installing any internal components. Use a
grounding wrist strap and place all electronic components in any static-shielded devices. Most
electronic components are sensitive to static electrical charge.
Disconnect the power cord from the Panel PC unit prior to any installation. Be sure both the
system and all external devices are turned off. Sudden surge of power could ruin sensitive
components. Make sure the Panel PC unit is properly grounded.
Do not open the system’s back cover. If opening the cover for maintenance is a must, only a
trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static
electricity. To avoid damaging chips from electrostatic discharge, observe the following
precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. This will help to discharge any static electricity on
human body.
When handling boards and components, wear a grounding wrist strap available from
most electronic component stores.
Please contact qualified technician for maintenance or repair.
Use only accessories and parts that are made by the qualified manufacturer.

iii
User’s Notice
Copyright of this manual belongs to the manufacturer. No part of this manual, including the products
and software described in it may be reproduced, transmitted or translated into any language in any
form or by any means without written permission of the manufacturer.
This manual contains all information required for the utilization of this product to meet the user’s
requirements. But it will change, correct at any time without notice. Manufacturer provides this manual
“as is” without warranty of any kind, and will not be liable for any indirect, special, incidental or
consequential damages (including damages for loss of profit, loss of business, loss of use of data,
interruption of business and the like).
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and they are used only for identification or explanation and to
the owner’s benefit, without intent to infringe.
Package Contents
Power Core
90W AC-DC Adapter
Panel PC System
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.

1
Chapter 1
Introduction
1-1 General Descriptions
Thank you for purchasing the system, a new product developed, designed and
manufactured under leading technical power and consistent dedication to fine
workmanship.
HPC150R-DCP6305E/HPC150R-DCP1135G7 series is a 15.0″ TFT Fanless
Touch Panel Computer which features:
15.0” 350 nits TFT LCD with LED backlight
5 Wire Resistive Touch/Anti-Reflection Protection Glass
Support Open frameless design
A true Flat, easy-to-clean front surface with edge-to-edge design
Front IP65 for protection against water and dust
Support for easy HDD and DARM installation
Support Cable less design
12-36V DC-in, with Electrical Over Stress (EOS) and OVP design
Onboard Intel® Tiger Lake SoC Processor
Support 2* DDR4 3200MHz Dual Channel SO-DIMM up to 64GB
Support HDMI Display
Support 1 * 7+15 Pin SATAIII (6Gb/s) device expansion
1* M.2 M-key (2242/2280), PCIe 4.0 x4interface, supports NVMe)
1* M.2 E-key (2230) USB2.0/PCIex1 interface supports CNVi
1* M.2 B-key (3042/3052/6570) supports 3G/4G/5G Module)
1* SIM card slot
2* Intel GbE, 2* USB3.2. (Gen2), 4* USB2.0
Support 2* RS232/422/485 & 2* RS232
Support CPU Smart FAN
Compliance with ErP standard
Support Watchdog function
The system has the following features besides other basic functions:
WiFi: the onboard M.2 E-key type-2230 PCI-E slot in the board supports
compatible WiFi card that can act as a mini wireless modem when external
antennas are connected. Different computers in the house can build wireless
connections through the system and take necessary data from it, thus reducing
the complexity in network establishment.
Dual Giga LAN: The system is integrated with dual Gigabit LAN network
controller realizing efficient power management for the operating system.
USB3.2 (Gen.2): Experience Fastest data transfers at 10Gb/s with USB3.2 Gen.2
the latest connectivity standard. Built connect easily with next-generation

2
components and peripherals, USB USB3.2 Gen.2 transfers data much faster
compatible with previous USB generations.
CPU Usage: The CPU Usage diagram shows a beautiful data curve that
indicates a pretty low CPU usage percentage for video playback of different
formats. GPU performances are excellent as well.
dB Value: The design of the system takes into consideration the needed quiet
operating environment in the living room and the average dB value is below 26
under normal operation to ensure the tranquility.
1-2 Specifications
Display
Front Bezel
IP65, NEMA 4 rugged protection, metal front bezel
Display Type
15.0" with LED Backlight
Brightness (cd/m²)
350 nits
Display Color
16.7m display color
Resolution
1024 x 768 @60Hz
Viewing Angle
178°/178° (H/V)
Pixel Pitch
0.099 x 0.297mm
Aspect Ratio
4:3
Contrast Ratio
1000:1
Response Time
35 ms
Touch Screen
Type
5 wires analog resistive type
Active Range
346.0 x 270.0mm ±0.3mm
Transparency
80 ±3%
Operating force
≦100g
Surface Hardness
≧3H(pressure 750g/45°)
Knock test
10,000,000 times
CASE
Panel Material
Aluminum
Case Material
Iron
Color
White
Coating Requirement
Spray Paint
Main System
CPU
HPC150R-DCP6305E: Intel®Tiger Lake 6305E
processor (1.8GHz/DC)
HPC150R-DCP1135G7: Intel®Tiger Lake i5-1135G7
processor (2.4GHz/QC)
RAM
Support 2* DDR4 SO-DIMM (Max 64GB)
Flash ROM
256MB SPI Flash ROM
Watchdog Timer
256 levels, 0~255 sec.
OS Support
Windows 10/Linux

3
Storage
SATA Port
Support 1* 2.5” SATA HDD (UPS Cell Option)
M.2 M Slot
1* M.2 M key (2242/2280, SATA/PCI-Ex4)
Expansion
M.2 Expansion Slot
1* M.2 E key (2230) for WIFI
1* M.2 B key (3042/3052/6570) for 4G/5G Module (4pcs
Built in Antenna)
I/O Connector
I/O Ports & Switches
2* USB3.2 (Gen.2)
4* USB2.0
2* RS232/422/485
2* RS232 or 2* GPIO(Optional)
1* HDMI
1* AT/ATX Mode Button
2* RJ45 LAN (1* Intel® I225V 2.5G, 1* Intel® I219LM
GbE)
1* 12~36V DC-in Locking Jack
1* Power button
1* 2pin Front Power button
Power
Power Input
12~36V DC-in
AC version: 100~240V AC‐DC 60W power adapter or
DC version: 12VDC with over current protection fuse
Power Consumption
45W
Dimensions
Case Dimensions
378.00 * 294.00 * 60.00mm
Certification Compliance
Certifications
CE, FCC, IP65(Front)
Environment
Temperature
Operating: -10°C ~ 50°C
Storage: -20°C ~ 70°C
Shock
1ms duration
Vibration
5~500Hz/1Grms
Warranty
Warranty
2 Years Limited Warranty （Panel and Touch is only
Warranty 1 Year）

4
1-3 I/O Outlets
Bottom Side:
*Note: The diagrams in this manual only serve for illustration. If there are any differences
that we do not cover, please refer to the actual product you purchase.
1-4 Connector Description
(1) Connector Functions
Icon
Name
Function
12~36V DC-in
Power Jack
For user to connect compatible power adapter to provide
power supply for the system.
Power Button
For user to turn on/off the system.
Power Button
Jack
For user to turn on/off the system.
AT/ATX Mode
Switch
AT/ATX mode Supported at front side I/O switch.
–AT: Directly PWR on as Power input ready
–ATX: Press Button to PWR on after Power input ready
*Note: User can switch up for ATX Mode or switch down for
AT Mode.
USB 3.2 Ports
To connect USB keyboard, mouse or other devices
compatible with USB3.2 specification. USB 3.2 Gen.2
ports supports up to 10Gbps data transfer rate.
USB 2.0 Ports
To connect USB keyboard, mouse or other devices
compatible with USB specification.
HDMI Port
To connect display device that support HDMI specification.

5
RJ-45 LAN Port
This connector is standard RJ-45 LAN jack for Network
connection.
Serial Port
Mainly for user to connect external MODEM or other devices
that supports Serial Communications Interface.
(*Optional)
GPIO Port-Male
Male General Purpose Input Output port.
(2) I/O Connector Description
DCIN1 (3-pin): 12~36V DC-in Power Connector
Pin No.
Definition
1
+12~36V VCC
2
GND
3
GND
Warning: Find Pin-1 position before connecting power cable to this 3-pin power connector. WRONG
INSTALLATION DIRECTION WILL DAMAGE THE BOARD!!
FPW_SW (2-pin block): Power button jack
RJ-45 Ethernet Connector
** There are two LED next to the LAN port. Please refer to the table below for the LAN
port LED indications.
For 1.0Gbps RJ-45 LAN port:
2.5Gbps RJ-45 LAN
1.0Gbps RJ-45 LAN

6
For 2.5Gbps RJ-45 LAN port:
COM Port & GPIO Connector
COM1/COM2:RS232/422/485 Serial Port;COM3/COM4: RS232 Serial Port.
The pin assignment for RS-232/ 422/ 485 is listed as follows:
1
2
3
4
5
6
7
8
9
Pin NO.
RS232
*RS422
(optional)
*RS485
(optional)
1
DCD
TX-
DATA-
2
RXD
TX+
DATA+
3
TXD
RX+
NC
4
DTR
RX-
NC
5
GND
GND
GND
6
DSR
NC
NC
7
RTS
NC
NC
8
CTS
NC
NC
9
RI
NC
NC
COM1 & COM2 ports can function as RS232/422/485 port. In normal settings
COM1/COM2 functions as RS232 port. With compatible COM cable they can function
as RS422 or RS 485 port. User also needs to go to BIOS to set ‘Transmission Mode
Select’for ‘Serial Port 1 Configuration’ or ‘Serial Port 2 Configuration’ (refer to
Page 28) at first, before using specialized cable to connect different pins of this port.
COM3: RS232
or GPIO
COM4: RS232
or GPIO
COM2:
RS232/422/485
COM1:
RS232/422/485

7
*Note: COM3 and COM4 from Panel PC can function as RS232 port or GPIO port by
order. User need to dissemble the whole heat sink back shell (refer to 2-4-3, step-1)
to make further settings on the daughter board for specific function.
User can set COM3/4 as GPIO port by setting up JP2~JP18 Pin(2-3) closed.
The pin assignment for GPIO connector is listed as follows:
For GPIO VCC please refer to jumper JP1 from the daughter board for further
settings:
JP2~JP18
JP1

8
Chapter 2
Hardware and Installation
2-1 Dimension and Outlines
* Measure Unit: mm.

9
2-2 To Open the Chassis
HPC150R-DCP6305E / HPC150R-DCP1135G7 series come with two expansion
covers on the backside of the chassis to simplify expansion procedures:
1. Put the system upon a stable platform with this side up. Tighten up the screws in
the marked spots to remove HDD and SO-DIMM covers.
2. User can install expansion parts according to their own needs: DDR4 SO-DIMMs,
M.2 M-key type-2242/2280 card, M.2 E-key type-2230 card, M.2 B-key
type-3042/3052/6570 card along with compatible Nano-SIM card, and compatible
2.5’’ hard disk.
HDD
Cover
DDR4 SO-DIMM
Cover

10
2-3 Jumper Settings
Jumper is a small component consisting of jumper clip and jumper pins. Install
jumper clip on 2 jumper pins to close the pins. And remove jumper clip from 2
jumper pins to open the pins. Diagram 2-1 illustrates how to set up a jumper.
JP1 (3-pin): EDP BACKLIGHT VCC Select (2.0 pitch)
JP2 (4-pin): EPD Panel VCC Select (2.0 pitch)
JP2 → EDP Panel VCC Select
2-4 Closed:
VCC=+3.3V;
3-4 Closed:
VCC=+5V;
4-6 Closed:
VCC=+12V
1
3
5
4
6
2
6
4
2
5
3
1
4
6
2
5
3
1
JPLED (3-pin): LCD BACKLIGHT VCC Select (2.0 pitch)
JPLED

11
JPLCD (4-pin): LCD Panel VCC Select (2.0 pitch)
JPLCD → LCD Panel VCC Select
2-4 Closed:
VCC=+3.3V;
3-4 Closed:
VCC=+5V;
4-6 Closed:
VCC=+12V
1
3
5
4
6
2
6
4
2
5
3
1
4
6
2
5
3
1
JPCOM1/2 (4-pin): COM1/COM2 Port Pin9 Function Select (2.0 pitch)
JPCOM1 → COM1 Port Pin-9
JPCOM2 → COM2 Port Pin-9
2-4 Closed:
PIN9=RS232;
3-4 Closed:
PIN9=+5V;
4-6 Closed:
PIN9=+12V
1
3
5
4
6
2
6
4
2
5
3
1
4
6
2
5
3
1
Pin (1-2) of JBAT (4-pin): Clear ME_RTC (2.0 pitch)
1-2 Closed: Clear ME_RTC
1-2 Open: Normal(Default)
PIN(1-2) Clear ME_RTC
Pin1
2
Pin1
2
3
4
4
3
JPCOM2
JPCOM1
JPLCD
JBAT

12
Pin (3-4) of JBAT (4-pin): Clear CMOS Setting (2.0 pitch)
3-4 Closed: Clear CMOS
3-4 Open: Normal(Default)
PIN(3-4) Clear CMOS
Pin1
2
Pin1
2
3
4
4
3
J80PORT (2-pin): GPIO Select (2.0 pitch)
1-2 Closed: GPIO
1-2 Open: 80 port
Pin1
2
Pin1
2
JBAT

13
2-4 Hardware Installation
2-4-1 To Install SO-DIMM to the Board
1. Locate the DDR4 SO-DIMM slots on the board.
2. Insert the gold-figure side of a
compatible SO-DIMM into the slot at a 30
degree. See to it that the break of the
module fit into the notch of the slot and
the golden-finger side should be fully
plugged into the slot.
3. Press down to secure the SO-DIMM
to the slot. The eject tabs will lock
automatically if installing direction is
correct.

14
2-4-2 To Install M.2 M-key Card
M2M slot: M.2 M-Key (2242/2280), PCIe 4.0 x4 interface supports NVMe.
1. Locate M.2 M-key slot on the board.
2. Remove the screw in the marked spot
(MH2; default) for further installation.
3. Insert the gold-figure side of compatible
M.2 M-key type-2242 card into the slot.
4. Lock the card to the board by
tightening up the screw to the marked
spot.
*Note: the screw post and nut fixed at location MH2 by default for 4.2cm type-2242
card installation. If you wish to install type-2280 card, please remove corresponding
screw post under the screw as well and lock the screw post into location MH4 before
installing 8 cm type-2280 card to the slot. The other steps are the same.

15
2-4-3 To Install M.2 E-key Wi-Fi Card
M2E slot: M.2 E-Key (2230), USB2.0/PCIex1 interface supports CNVi.
*Note:User needs to pick out the WIFI antenna string and press the metal hat on the
string end to corresponding metal button on the installed WiFi card, so they need to
remove the whole chassis heat sink shell on the back of the Panel PC for further
installation, which is different from 2-2, please refer to the following steps for the
installation of the compatibale M.2 E-Key Wi-Fi card:
1. Remove the screws in the marked red circle spots and dissemble the whole
chassis heat sink shell from the Panel PC.

16
2. The WiFi antenna strings (for better signal reception) are tied up in a bundle with
other cables; Pick out the antenna strings from the bundle and tear off the acetate
tape which protects the metal hats of the string end.
Notice
：
The other wires/cables must be wrapped with Insulated Tape and placed in the
original position to avoid short circuit caused by contact between the metal parts and the
mainboard.
3. Locate M.2 E-key slot on the board.
4. Remove the screw post & screw nut in
the marked spot (MH1).