Jiffy Steamer Esteam J-Series User manual

Worldwide Leader in
Steaming Equipment Since 1940
Esteam®and J-Series
OWNER’S MANUAL

Congratulations and Thank You!
Table of Contents
2
Thank you for purchasing your Jiffy®Steamer
from the world’s leading manufacturer of
steaming equipment since 1940.We strive to
engineer and manufacture the very best
steamer available backed by
superior customer service.
With proper maintenance and cleaning, your Jiffy®
Steamer will last through years of demanding use.
Thank you again and we sincerely appreciate your
business. Warmest regards,
Jiffy®Steamer Company, LLC
Made in the USA Since 1940
Safety Instructions.....................................................................3
How to Steam..............................................................................4
Esteam®Hand Held Steamer.................................................5-8
Rod Set Assembly.......................................................................9
Model J-1, J-2 & J-200 Jiffy®Steamers............................10-15
Model J-2000 Jiffy®Steamer..............................................16-21
Model J-4000 Jiffy®Steamer..............................................22-27
Model J-1, J-2, J-200 & J-2000 Jiffy®Steamers
Cleaning Instructions...............................................................28
Model J-4000 Jiffy®Steamer Cleaning Instructions.............29
Jiffy®Steamer Maintenance....................................................30
Jiffy®Steamer Accessories.......................................................31
Jiffy®Steamer Steam Head Configurations...........................32
Jiffy®Steamer Cord Plug Configurations..............................33
Troubleshooting ..................................................................34-35
Jiffy®Matrix Charts...........................................................36-39
Product Specifications .............................................................40
Jiffy®Steamer Warranty & Return Policy ............................41
Jiffy®Steamer Extended Warranty........................................42

3
Jiffy®Steamer Safety Instructions
When using your Jiffy®Steamer, basic precautions should always
be followed, including the following:
1. Read all instructions prior to usage.
2. To reduce the risk of contact with hot water emitting from steam vents,
check appliance before each use by holding it away from body and operating.
3. Use appliance only for its intended use. Steam only in an up and down
vertical motion. Never use steamer in a horizontal position
or tilt into a backward position, this may result in water discharge.
4. To avoid the risk of electric shock, do not immerse the appliance in
water or other liquids.
5. Never tug cord to disconnect from outlet; instead grasp plug and pull to
disconnect.
6. Do not allow cord to touch hot surfaces. Let appliance cool completely
before storing.
7. Always disconnect appliance from electrical outlet when filling with water,
emptying, and when not in use.
8. Do not operate appliance with a damaged cord, or if the appliance has been
dropped or damaged. To reduce the risk of electric shock, do not disassemble
or attempt to repair the appliance, take it to a qualified service person or return
to the Jiffy®Steamer factory for examination and repair. Incorrect reassembly or
repair could cause a risk of fire, electric shock or injury to persons when the
appliance is used.
9. Close supervision is necessary for any appliance being used by or near children.
Do not leave appliance unattended while connected to power source.
10. Burns could occur from touching hot parts, hot water or steam. Use care
when you empty a steam appliance as there may be hot water in the reservoir.
11. Indoor use only.
12. Never attempt to steam clothing while on body.
SAVE THESE INSTRUCTIONS
RISK OF
ELECTRIC
SHOCK
RISK OF
BURNS

How to Steam
As your drycleaner knows, steam is the gentlest, safest, most efficient method to
remove wrinkles. Not only is steaming five times faster than ironing, it is guaranteed
not to scorch even the most delicate materials and fabrics. Our steamers will remove
wrinkles from clothing, drapery, tablecloths...virtually any fabric. Use the following
information to help guide you to more proficient steaming.
Some articles
can be steamed
better from the
underside. This
allows the
steam to relax
the fibers of the
material, thus
removing the wrinkles.
Jiffy®Steamers are
great for removing
“closet crunch,”and
they eliminate most
trips to the drycleaner.
Convenient hanger/hook
mechanism holds both clothes and
steam head securely.
Always steam with
hose in upright
position so any
condensation is free
to flow back into
the steamer. If
steaming in a low
position near floor,
frequently extend hose up and out
to keep clear.
Pants may be easily steamed by
hanging then by the cuff.You may
also use your Jiffy Steamboard to
serve as a vertical pressing board to
position your garments.
4
When steaming,
touch material
lightly with steam
head and wrinkles
will vanish instantly.
The combination of
the steam and the
steam head is
important for a
smooth finish. Do not directly touch
velvet or silk with the steam head.

Esteam®Features and Directions.
ESTEAM®
Directions for Use
1. Make sure your Esteam®is unplugged before filling.
2. Check to make sure the factory-installed red o-ring is
secure inside the water tank before operating steamer
(figure #1).
3. Fill with tap or distilled water to the full mark on the outside of the steamer.
Never overfill. Never use water left overnight in steamer. Stale water causes
foaming action and can create water droplets.
4. After filling, place steam cap on steamer and twist firmly until cap
arrows align with arrows on the tank (figure #2). Make
sure it is secure before operating unit.
5. Plug your Esteam®into proper voltage outlet. Steamer
will start heating within 15 seconds, providing live
steam from cold water within 2 minutes.
6. Always steam with a vertical up and down motion (figure #3).
Do not tilt unit forward or backward.
7. Avoid allowing steamer to run dry of water.
8. Refer to page 8 for complete cleaning instructions.
WARNING: Never operate without water. Unplug after each use.
Figure 1 Figure 2
5
Features
•3 times more powerful than any other
hand-held steamer on the market
•Largest water reservoir available
•Wide mouth, easy-to-fill water tank
•600-watt heating element; automatic safety
shut-off temporarily cuts unit off when
it runs dry
•Uses plain tap or distilled water (no
additives required)
•Comfortable, easy-to-grip handle
•Special outer housing for cool-to-the-
touch operation
•No internal water lines or pumps to
become clogged by hard water
•9-foot power cord for more manageable
handling
•Fits neatly inside attachéor suitcase
•Available with a multiple plug converter for world travel
Owner’s
Manual
Steam Cap
Figure 3
Includes:
ESTEAM®
Main Body

Esteam®Parts Diagram
6

7
Esteam®Parts Diagram Key
ESTEAM®
Should you ever need replacement parts for your Jiffy®Steamer, you may purchase
them separately. Use this handy diagram and parts list to identify any part you may
need. Please include model and serial number when ordering.
Jiffy Steamer List
Key# Part # Part Description Price
10653 Esteam 120 Volt 600 Watt Heater $ 17.00
with Gaskets and Nut
0655 Esteam 230 Volt 600 Watt Heater $ 17.00
with Gaskets and Nut
1a. Esteam Heater
(Sold with Item #0653 or #0655 as a Kit)
1b. Gasket for Esteam Heater
(Sold with Item #0653 or #0655 as a Kit)
1c. Nut for Esteam Heater
(Sold with Item #0653 or #0655 as a Kit)
20661 Red Inside O-Ring $ 1.50
30662 Black Outside O-Ring $ 1.50
40669 Esteam Water Tank $ 24.00
50640 Esteam 36 T-L263 Thermostat $ 6.75
60643 Fusible Link Clamp $ 1.50
70644 Fusible Link Clamp Screw $ 0.50
80641 Fusible Link Wire with Insulated Lug (Orange) $ 2.50
90681 Red Wire with Insulated Lug $ 1.50
10 0645 Pilot Light with Wiring Harness
for 120 Volt Electrical Systems $ 7.00
0646 Pilot Light with Wiring Harness
for 230 Volt Electrical Systems $ 7.00
11 0647 Cord set (18/2 gauge) $ 7.00
12 0665 Right Case Half $ 14.00
13 0666 Left Case Half $ 14.00
14 0667 Four (4) Screws for Esteam Outer Case Halves $ 1.00
15 0663 Complete Steam Cap with Face Plate $ 20.00
ACCESSORIES
0619 Voltage Converter for Travel $ 19.00
0898 Liquid Cleaner - 3 Ten (10) Ounce $ 15.00
Bottles per Package*
*Not Available for Export.

8
Esteam®Cleaning Instructions
Once you begin to see calcium scale
collect in the bottom of your
ESTEAM®hand steamer, it is time
to use the Jiffy®Steamer Liquid
Cleaner. Please follow these
instructions:
1. Pour 4 ounces of water in your
ESTEAM®hand steamer.
2. Plug in the unit and bring to full steam.
3. Unplug the unit and allow to cool for 2
minutes.
4. Pour out all water.
5. Pour in 5 ounces (1/2 bottle) of the Jiffy®Steamer Liquid Cleaner.
6. Leave the cleaner in the unit for 2 hours. May require scrubbing with a stiff
bristle brush to remove excess sediment.
7. DO NOT STEAM THE UNIT WITH THE LIQUID CLEANER.
8. Pour out Liquid Cleaner.
9. Flush the unit 3 times with fresh water.
10. Resume steaming.

J-Series Rod Set Assembly
9
1. Screw all three (3) sections of the
rod set together (hook, middle, and
bottom sections).
2. Slide bottom section of rod
(marked “A”on drawing) through
the rod set nut (marked “B”on
drawing) with the threads facing
down.
3. Place 1/2 inch split ring (marked
“C”on drawing) on bottom section
of rod set approximately 1/2 inch
from the end of the rod. Please note
that steps 2 and 3 are completed at
the Jiffy®Steamer factory.
4. Insert entire assembly into threaded
base adapter on top of the steamer
base (marked “D”on drawing).
Press down firmly so that split ring
(marked “C”on drawing) will slide
up on the rod and come to rest at
the top of the base adapter once the
rod set is completely inserted.
5. Tighten the rod set nut (marked “B”
on drawing) with assembly wrench
provided with all J-Series Jiffy®
Steamer (wrench is magnetized and
may be found on the bottom plate of
the unit).
A
B
C
D
J-Series

J-2 Base Unit
Rod Set
(not included with
J-1 series)
Jiffy®J-1/J-2/J-200 Model Steamer
10
FEATURES
•Cast aluminum housing for durability (Models J-1 and J-2)
•High impact polymer housing (Model J-200)
•Lightweight, flexible hose - Models J-2/J-200 (J-1 series
utilizes a brass hat nozzle)
•Shatterproof water bottle
•Safety wiring feature temporarily turns the unit off if it
accidentally runs dry
•Comfortable, easy-to-grip handle
•Removes wrinkles up to five times faster than
conventional ironing
•Easy-roll casters for mobility (casters not included with
J-1 series)
•Numerous steam head attachments available
•120 Volt or 230 Volt units available
•Backed by Jiffy®’s renowned customer service--should your
steamer need repair, send it to us and we will repair and ship
the unit within 24 hours from its arrival to our plant
Assembly
Wrench
Water
Bottle
INCLUDES:
Steam Head
and Hose
Attachment
Owner’s
Manual Hat Nozzle
(J-1 Models)

J-2
1 . For J-2/J-200 models, attach hose firmly with included
assembly wrench, which is magnetized and located on
the bottom of the unit (figure #1).Assemble and attach
hose hanger rod set. See page 9 for assembly instructions.
For J-1 models, the brass hat nozzle should already be
attached. There is no rod set for J-1 models.
2. Invert bottle of fresh tap or distilled water, plug into
proper voltage outlet, turn switch to lighted ON position
and you will have steam within minutes. Never substitute the Jiffy®
Steamer water bottle.
3. For easy operation, mount optional Jiffy®Steamboard to
door or wall to hold clothing while steaming (figure #2).
For hanging garments without optional Jiffy®
Steamboard, simply install an eye screw or nail to inside
of a doorway or directly onto a wall or you may use
steamer’s rod set as shown in figure 3. Touch material
lightly with steaming head and wrinkles will vanish
instantly. The combined touch of the steaming head and
the direct steam is very important. Some articles can be
steamed better from the underneath side. Speed and
efficiency is accomplished with a little practice. Always
steam with hose in an upright position, so any
condensation is free to flow back into steamer. If
steaming in a low position near floor, extend hose up and
out frequently to keep clear of
condensation. DO NOT ALLOW
STEAMER TO RUN DRY.
4. Hang steam head in an upright
position in the hose hanger section
when not in use and turn switch to
OFF (figure #3).
5. Periodically, pour old water out of
steamer to avoid sediment buildup and
maintain proper water level (figure
#4). Remove hard water deposits with Jiffy®Liquid
Cleaner. See page 28 for complete cleaning
instructions.
NOTE: No two water supplies have the same mineral content. If your steamer
begins to cut on and off during normal use, the thermostat is indicating the
heating unit needs the sediment cleaned out.
Figure 1
Jiffy®J-1/J-2/J-200 Model Steamer Directions
Figure 2
Figure 3
Figure 4
11

Jiffy Steamer List
Key# Part # Part Description Price
11030 Rod Set and Nut Complete with Metal Studs $ 25.50
0031 Hose Hanger Rod Set with Adapter Complete $ 25.50
0031A Hose Hanger Rod Set without Adapter Complete $ 21.50
0041 Base Adapter with Thumb Screw (for Old Style Rods Sets) $ 4.00
20035 Hook Section of Rod Set $ 6.50
Should you ever need replacement parts for your Jiffy®Steamer, you may
purchase them separately. Use this handy diagram and parts list to identify any
part you may need. Please include model and serial number when ordering.
Jiffy®J-1/J-2/J-200 Parts Diagram
12

13
Jiffy®J-1/J-2/J-200 Parts Diagram Key
J-1/J-2/J-200
30036 Middle Section of Rod Set $ 7.50
40037 Bottom Section of Rod Set $ 7.50
50043 Metal Threaded Cap Screw for Rod Set $ 1.50
60039 Metal Threaded Stud for Rod Sections $ 1.50
71031 1/2”Split Ring for Rod Set $ 0.50
81032 Rod Set Nut $ 6.00
90253 Plastic Steam Head/Handle Replacement Kit $ 22.00
10 0251 Plastic Head/Handle Hose Attachment Complete $ 50.00
0280 Hose Per Foot (Black in Color) $ 3.00
11 0002 Painted Die Cast Aluminum Housing $ 51.50
0023 Plastic Water Bottle “A”with Cap $ 6.50
0027 Replacement Cap for Water Bottle “A”$ 0.75
12 0026A Plastic Water Bottle “B”without Check Valve Cap $ 5.75
13 0025 Plastic Water Bottle “B”with Check Valve Cap $ 9.50
14 0027A Replacement Check Valve Cap for Water Bottle “B”$ 3.75
15 0004 Round Beauty Ring $ 0.75
0122 Toggle Switch (3 Pieces) $ 7.50
0127 Red Neon Pilot Light with Lock Ring 120 Volt $ 4.00
0128 Red Neon Pilot Light with Lock Ring 230 Volt $ 4.00
16 1125 Green Lighted Contura Rocker Switch 120 Volt $ 9.00
1126 Green Lighted Contura Rocker Switch 230 Volt $ 9.00
17 0132 Cord Set (16/3 gauge) with Strain Relief $ 9.50
18 0146B Cord Strain Relief $ 1.50
19 0028 Water Cup with 90 Degree Brass Fitting $ 18.00
0147 Internal Wire Set for Models with Front Red Light $ 9.00
20 0148 Internal Wire Set for Models with Green Contura Rocker Switch $ 9.00
0596 Heating Unit Kit (wiring included) for Models with Front Red Light
–120 Volt Cord Set and 4”Water Line $ 81.50
0177A Heating Unit Kit (wiring included) for Models with Front Red Light
–230 Volt Cord Set and 4”Water Line $ 81.50
0597 Heating Unit Kit (wiring included) for Models with Green Lighted
Rocker Switch - 120 Volt Cord Set and 4”Water Line $ 81.50
0597A Heating Unit Kit (wiring included) for Models with Green Lighted
Rocker Switch - 230 Volt Cord Set and 4”Water Line $ 81.50
0161A Heating Unit Assembly (no wiring included)
–120 Volt and 4”Water Line $ 62.50
0162A Heating Unit Assembly (no wiring included)
–230 Volt and 4”Water Line $ 62.50
21 0030 Brass 90 Degree Elbow Joint $ 2.50
22 1130 3/8”x 1/4”Straight Brass Fitting for Heating Element Housing $ 2.50
23 0187 Copper Tube (4”length) with Nuts and Compression Rings $ 4.00
24 0160 L-290 Thermostat $ 8.00
25 0195 Fusible Link Clamp $ 1.50
26 0151 Fusible Link Wire with Insulated Lug $ 3.00
27 0009 Bottom Plate with Casters $ 13.50
28 0011 Bottom Plate Casters (Set of 4) $ 6.50
29 0010 Screws for Bottom Plate (4 Screws Total) $ 0.75
ACCESSORIES
30 1050 Jiffy SteamerAssembly Wrench $ 4.00
0274 Brass Hat Nozzle Attachment $ 13.00
0254 Metal Head/Wood Handle HoseAttachment Complete $ 70.00
0256 Metal Head / Wood Handle Only $ 37.50
0269 Replacement Wooden Handle (for Metal Steam Heads) $ 7.00
0262 Wig Hose Attachment $ 50.00
1062 Steam Cleaning “B”Brush Hose Attachment $ 50.00
1063 Brush Only for the B”Hose Attachment $ 8.00
0898 Liquid Cleaner - 3 Ten (10) Ounce Bottles per Package* $ 15.00
*Not Available for Export.

Jiffy®J-1/J-2/J-200 Wiring Diagram
14
Caution:
Insure that the power cord is
unplugged from the electrical
outlet before attempting to
repair your Jiffy®Steamer.

15
Jiffy®J-1/J-2/J-200 Wiring Instructions
1. Insert cordset into housing and connect white neutral wire from cordset
bundle to terminal number 5 on the switch.
2. Connect blue wire from the right side of heating element to the right side
of the L-290 thermostat.
3. Insert brass heating unit into housing and tighten with 2 mounting screws.
Connect green ground wire (from cordset) to the nearer of the two mount-
ing screws. (In older J-2s, groundwire may also be attached to internal
boss of housing.)
4. Connect black positive wire from cordset to plastic connector on orange
fusible link wire.
5. Connect other end of orange fusible link to terminal number 2
on the switch.
6. Connect yellow wire from the left side of the thermostat to terminal
number 3 on the switch.
7. Connect white wire from the left side of the heater unit to terminal
number 6 on switch.
8. Insert one end of copper water line and compression ring into threaded
fitting at bottom of brass heating unit and tighten nut with a 5/8" wrench.
9. Connect other end of water line with compression ring to 90 degree brass
elbow at bottom of water cup and tighten with a 5/8" wrench. (Heating unit
may be loosened and adjusted for a better fit if necessary.)
10. Set steamer upright and place black plastic strain relief approximately
41/2" from end of cord and insert into housing using pliers.
11. Secure bottom plate with four screws.
12. To avoid leakage, be sure and tighten hose (or hat nozzle) with wrench
before using steamer.
Please note switch terminal numbers 2, 3, 5 and 6 indicated on
the enlarged switch diagram are marked on the actual switch.
Jiffy®Steamers manufactured before May 2000 are not
marked with the terminal switch numbers, but the terminal
blades are in the same location.

Jiffy®J-2000 Model Steamer
16
FEATURES
•Polymer outer housing unit for durability
•Lightweight, flexible hose
•Shatterproof water caddy
•Safety wiring feature temporarily turns the unit off should it
accidentally run dry
•Comfortable, easy-to-grip handle
•Removes wrinkles up to five times faster than conventional
ironing
•Easy-roll casters for mobility
•Numerous steam head attachments available
•Backed by Jiffy®’s renowned Customer Service--should your
steamer need repair, send it to us and we will repair and ship
the unit within 24 hours from its arrival to our plant
INCLUDES:
J-2000 BaseUnit
Rod Set
(not included with
J-1 series)
Owner's
Manual Assembly
Wrench
Water
Caddy
Steam Head
and Hose
Attachment
Check
Valve Cap

Jiffy®J-2000 Directions
1. Attach hose firmly with included assembly wrench,
which is magnetized and located on the bottom of the
unit. Assemble and attach hose hanger rod set. See
page 9 for assembly instructions.
2. Invert water caddy filled with distilled or tap water,
plug into proper voltage outlet, turn switch to lighted
ON position and you will have steam within minutes. Never
substitute the Jiffy®Steamer water caddy.
3. For easy operation, mount optional Jiffy®Steamboard to door or wall to
hold clothing while steaming (figure #2). For hanging garments without
optional Jiffy®Steamboard, simply install an eye screw
or nail to inside of a doorway or directly onto a wall or
you may use your steamer’s rod set as shown in figure
3. Touch material lightly with steaming head and
wrinkles will vanish instantly. The combined touch of
the steaming head and the direct steam is very
important. Some articles can be steamed better from the
underneath side. Speed and efficiency is accomplished
with a little practice. Always steam with hose in an
upright position, so any condensation is free to flow
back into steamer. If steaming in a low position near
floor, straighten hose up and out frequently to keep
clear of condensation. DO NOTALLOW STEAMER
TO RUN DRY.
4. Hang steam head in an upright position in the hose hanger
section when not in use and turn switch to OFF (figure #3).
5. Periodically, pour old water out of steamer to avoid
sediment buildup and maintain proper water level (figure
#4). Remove hard water deposits with
Jiffy®Liquid Cleaner. Wipe water cup
out with a hand towel. See page 28 for
complete cleaning instructions.
NOTE: No two water supplies have the same mineral
content. If your steamer begins to cut on and off during
normal use, the thermostat is indicating the heating unit
needs the sediment cleaned out.
Figure 1
J-2000
Figure 2
Figure 3
Figure 4
17

Should you ever need replacement parts for your Jiffy®Steamer, you may
purchase them separately. Use this handy diagram and parts list to identify any
part you may need. Please include model and serial number when ordering.
Jiffy®J-2000 Parts Diagram
18

Jiffy Steamer List
Key# Part # Part Description Price
11030 Rod Set and Nut Complete with Metal Studs $ 25.50
20035 Hook Section of Rod Set $ 6.50
30036 Middle Section of Rod Set $ 7.50
40037 Bottom Section of Rod Set $ 7.50
50043 Metal Threaded Cap Screw for Rod Set $ 1.50
60039 Metal Threaded Stud for Rod Sections $ 1.50
71031 1/2”Split Ring for Rod Set $ 0.50
81032 Rod Set Nut $ 6.00
90253 Plastic Steam Head/Handle Replacement Kit $ 22.00
10 0251 Plastic Head/Handle Hose Attachment Complete $ 50.00
0280 Hose Per Foot (Black in Color) $ 3.00
11 1100 J-2000 Plastic Housing Kit $ 58.00
12 1140 J-2000 Water Caddy Complete
with Check Valve Cap $ 28.00
13 1141 J-2000 Water Caddy Complete
with out Check Valve Cap $ 24.25
0027A Replacement Check Valve Cap $ 3.75
14 0004 Round Beauty Ring $ 0.75
15 1125 Green Lighted Contura Rocker Switch - 120 Volt $ 9.00
1126 Green Lighted Contura Rocker Switch - 230 Volt $ 9.00
16 0132 Cord Set (16/3 gauge) with Strain Relief $ 9.50
17 0146B Cord Strain Relief $ 1.50
18 0148 Internal Wire Set $ 9.00
1193 Heating Unit Kit (wiring included) for Models with Green
Lighted Contura Rocker Switch - 120 Volt Cord Set and
4 1/2”Water Line $ 81.50
1194 Heating Unit Kit (wiring included) for Models with Green
Lighted Contura Rocker Switch - 230 Volt Cord Set and
4 1/2”Water Line $ 81.50
19 0161B Heating Unit Assembly (no wiring included) for
Models with Green Lighted Rocker Switch - 120 Volt
Cord Set and 4 1/2”Water Line $ 62.50
0162B Heating Unit Assembly (no wiring included) for
Models with Green Lighted Contura Rocker Switch -
230 Volt Cord Set and 4 1/2”Water Line $ 62.50
20 0030 Brass 90 Degree Elbow Joint $ 2.50
21 1130 3/8”x 1/4”Straight Brass Fitting for
Heating Element Housing $ 2.50
22 0187 Copper Tube(41/2”length) with Nuts and
Compression Rings $ 4.00
23 0160 L-290 Thermostat $ 8.00
24 0195 Fusible Link Clamp $ 1.50
25 0151 Fusible Link Wire with Insulated Lug $ 3.00
26 1120 Bottom Plate with Casters $ 18.00
27 0011 Bottom Plate Casters (Set of 4) $ 6.50
28 0010 Screws for Bottom Plate (4 Screws Total) $ 0.75
ACCESSORIES
29 1050 Jiffy SteamerAssembly Wrench $ 4.00
0254 Metal Head/Wood Handle HoseAttachment Complete $ 70.00
0256 Metal Head / Wood Handle Only $ 37.50
0262 Wig Hose Attachment $ 50.00
1062 Steam Cleaning “B”Brush Hose Attachment $ 50.00
1063 Brush Only for the “B”Hose Attachment $ 8.00
0898 Liquid Cleaner - 3 Ten (10) Ounce Bottles per Package* $ 15.00
*Not Available for Export.
19
Jiffy®J-2000 Parts Diagram Key
J-2000

Jiffy®J-2000 Wiring Diagram
20
Caution:
Insure that the power
cord is unplugged from
the electrical outlet before
attempting to repair your
Jiffy®Steamer.