JL Audio Stealtbox SB-K-SL-12W0v2 User manual

INSTALLATION GUIDE
for the
SB-K-SL-12W0v2
SKU#94493,94494
2010 +
Thank you for choosing a JL Audio Stealthbox®for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox®installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox®be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
S T E P 1
Empty out the trunk of the car so that you have a clean area
to work in.
Continued on Next Page
S T E P 2
Lift the floor, remove the compartmented foam spacer this
will not remain in the vehicle.
S T E P 3
Remove the tool kit that resides inside the spare tire and the
spare tire itself, set aside the hardware as it will be re-used.
SB-K-SL-12W0v2 INSTR_SKU# 011315
INSTALLATION
D I F F I C U LT Y :
25
OUT
OF
ESTIMATED TIME:
1 HOUR

Continued on Next Page
SB-K-SL-12W0v2 INSTR_SKU# 011315
S T E P 7
Locate the four holes in the Spare Tire Platform, align them
with the four threaded inserts in the Stealthbox® and mount
the Spare Tire Platform to the Stealthbox® using the four
included 1/4-20 x 1-1/2” Allen Head Bolts.
S T E P 6
Mount the 8mm x 38mm Coupling Nut to the steel strap as
shown using the 8mm x 16mm Hex Cap Screw and 5/16”
Split Lock Washer to secure the Coupler to the Custom
Mount Strap.
Mount the Custom Mount Strap with the Coupling
Nut attached to the Stealthbox® on the top side of the
Stealthbox, in the spare tire recess, as shown using the two
included 1/4-20 x 2” Phillips Head Screws.
S T E P 5
Thread the three included Allen Head Studs into the bottom
of the Stealthbox® as shown, leaving approximately 1/2”
exposed.
S T E P 4
From the rear of the vehicle looking into the spare tire well,
position the three Wax Squares as shown, make sure that the
Wax Squares adhere to the floor well so that they don’t shift
while making impressions in them.
Page 2 • JL Audio, Inc 2010
S T E P 9
Using a 1/2” drill bit, drill through the three marks in the Wax
Squares.
Before drilling, always make sure that you are not
going to be drilling into any gas lines, brake lines,
tires, transmission lines, electrical wiring, exhaust
systems or anything else that might cause a
reduction in your weekly pay.
Always wear eye protection when drilling!
STEP 11
Set the spare tire in place and secure it through the threaded
coupler (seen in Step 6) using the original hardware that
secured the tire in place before the installation of the
Stealthbox®
STEP 10
Set the Stealthbox® back into the car, positioning it so that
the Allen Head Set Screws come through the holes drilled in
Step 9. From under the vehicle, secure the Stealthbox® in
place by putting a Fender Washer, Split Lock Washer and Hex
Nut on each Allen Head Set Screw. Progressively tighten all
three studs as if you were changing a tire so that all three get
tightened evenly.
S T E P 8
Gently set the Stealthbox® in place centering the Spare Tire
Platform in the recess. Once the Stealthbox ® is in place, put
enough pressure on it to cause the three Allen Head Set
Screws to mark the Wax Squares. Remove the Stealthbox®
from the vehicle making sure that the Wax Squares stay in
place on the floor of the spare tire well.

SB-K-SL-12W0v2 INSTR_SKU# 011315
Page 3• JL Audio, Inc 2010
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc.“Ahead of the Curve”and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU#011315 08.09.2010 • Printed in USA • ©2010 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 OtherU.S. & Foreignpatentspending.
For more detailed information please visit us online at www.jlaudio.com.
[phone]
www.jlaudio.com
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
I N C L U D E D H A R D W A R E
1) 8mm x 38mm Coupling Nut 1) 8mm x 16mm Hex Cap Screw
3) 3/8-16 x 2-1/4” Allen Head Set Screw 3) 3/8-16 Hex Nut
3) 3/8” x 1-1/4” Fender Washer 3) 3/8” Split Lock Washer
3) 3” x 3” Wax Square 4) 1/4-20 x 1-1/2” Allen Head Bolt
2) 1/4-20 x 2” Phillips Flathead Screw 1) 5/16” Split Lock Washer
1) Custom Mount Strap
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 12W0v2-4
Nominal Impedance: 4 Ohms
Continuous Power Handling: 300 Watts
P O W E R R E C O M M E N D A T I O N
JL Audio recommends high quality amplifiers such as the JL Audio XD400/4. The picture below shows the
recommended settings for the XD400/4. If another amplifier is being used, please reference this illustration and
use similar settings on that amplifier. All JL Audio amplifiers are very versatile audio components. Please consult
the owner’s manual for even more detailed information about installing and tuning your amplifier.
C O N N E C T I O N S
Using quality power, signal and speaker wire is essential in ensuring the performance of your Stealthbox®.
JL Audio recommends using a 4 AWG power kit such as the XC -PCS4-1B for your Stealthbox® amplifier, other
kits are available should you be using more than one amplifier. Signal wire such as the JL Audio Premium
Audio Interconnect Cables should be used that will provide signal for both channels of the amplifier. JL Audio
recommends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Including a full Slampak® system designed for the Soul (SKU-94494)
Front/ Rear Speaker Size - Front Location: 6-1/2”- Front Doors
Fits JL Audio Models: TR650-CXi, C2-650x, C3-650, C5-650, C5-650x & ZR650-CSi
S T E P 1 5
C O N G R A T U L A T I O N S !
You have completed the installation for this model!
Enjoy your new Stealthbox®!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
S T E P 1 4
If mounting an amplifier in the recess make sure to mount
the amplifier panel to the Stealthbox® first and then the amp
to the panel so that extra holes will not be drilled into the
Stealthbox®.
S T E P 1 3
The recess on the top of the Stealthbox® was specifically
designed to be a good mounting location for an amplifier.
The amplifier shown is the JL Audio XD400/4. See
recommendations below if this is where the amp will be
mounted.
S T E P 1 2
Replace the tool kit that was removed in Step 2.